ASTM B711-18

Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)

ABSTRACT
This specification covers concentric-lay-stranded conductors made from round-alloy 6201-T81 hard:solution heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or aluminum-clad steel core wire for use as overhead electric conductors. Cold-pressure welds, electric-butt welds, and electric-butt, cold-upset welds in the finished individual aluminum alloy wires composing the conductor may be made during the stranding process. The direction of lay of the outside layer of aluminum-alloy wires shall be right-hand. The direction of lay of the aluminum alloy and steel wires shall be reversed in successive layers. The rated strength of a conductor shall be taken as the sum of the strengths of the aluminum alloy and steel components. The mass and electrical resistance of a unit length of stranded conductor shall be calculated. The ares of cross section may be determined by calculations from diameter measurements of the component aluminum wires at any point when measured perpendicularly to their axes.
SCOPE
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-alloy 6201-T81 hard: solution heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or aluminum-clad steel core wire for use as overhead electric conductors (Explanatory Note 1 and Note 2).  
Note 1: The alloy and temper designations conform to ANSI H35.1. Aluminum alloy 6201 corresponds to Unified Numbering System alloy A96201 in accordance with Practice E527.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 28-Feb-2018
• ICS: 29.240.20 - Power transmission and distribution lines
• Technical Committee: B01 - Electrical Conductors
• Drafting Committee: B01.07 - Conductors of Light Metals

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B711 −18
Standard Specification for
Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel
1
Reinforced (AACSR) (6201)
This standard is issued under the fixed designation B711; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Area of Stranded Conductors
B354 Terminology Relating to Uninsulated Metallic Electri-
1.1 This specification covers concentric-lay-stranded con-
cal Conductors
ductors made from round aluminum-alloy 6201-T81 hard:
B398/B398M Specification for Aluminum-Alloy 6201-T81
solution heat treated, cold worked, and then artificially aged
and 6201-T83 Wire for Electrical Purposes
wire and round zinc-coated, Zn-5Al-MM coated, aluminum-
B498/B498M Specification for Zinc-Coated (Galvanized)
coated, or aluminum-clad steel core wire for use as overhead
Steel Core Wire for Use in Overhead Electrical Conduc-
electric conductors (Explanatory Note 1 and Note 2).
tors
NOTE 1—The alloy and temper designations conform to ANSI H35.1.
B500/B500M Specification for Metallic Coated or Alumi-
Aluminum alloy 6201 corresponds to Unified Numbering System alloy
num Clad Stranded Steel Core for Use in Overhead
A96201 in accordance with Practice E527.
Electrical Conductors
1.2 The values stated in SI units are to be regarded as
B502 Specification for Aluminum-Clad Steel Core Wire for
standard. No other units of measurement are included in this
Use in Overhead Electrical Aluminum Conductors
standard.
B606 Specification for High-Strength Zinc-Coated (Galva-
1.3 This standard does not purport to address all of the nized) Steel Core Wire for Aluminum and Aluminum-
Alloy Conductors, Steel Reinforced
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- B802/B802M Specification for Zinc–5 % Aluminum-
Mischmetal Alloy-Coated Steel Core Wire for Aluminum
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use. Conductors, Steel Reinforced (ACSR)
B803 Specification for High-Strength Zinc–5 % Aluminum-
1.4 This international standard was developed in accor-
Mischmetal Alloy-Coated Steel Core Wire for Use in
dance with internationally recognized principles on standard-
Overhead Electrical Conductors
ization established in the Decision on Principles for the
B957 Specification for Extra-High-Strength and Ultra-High-
Development of International Standards, Guides and Recom-
Strength Zinc-Coated (Galvanized) Steel Core Wire for
mendations issued by the World Trade Organization Technical
Overhead Electrical Conductors
Barriers to Trade (TBT) Committee.
B958 Specification for Extra-High-Strength and Ultra-High-
Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-
2. Referenced Documents
Coated Steel Core Wire for Use in Overhead Electrical
2.1 The following documents of the issue in effect on date
Conductors
of material purchase form a part of this specification to the
E29 Practice for Using Significant Digits in Test Data to
extent referenced herein.
Determine Conformance with Specifications
2
2.2 ASTM Standards:
E527 Practice for Numbering Metals and Alloys in the
B263 Test Method for Determination of Cross-Sectional
Unified Numbering System (UNS)
2.3 American National Standards Institute Standard:
H35.1M Alloy and Temper Designation Systems forAlumi-
1 3
This specification is under the jurisdiction of ASTM Committee B01 on
num
Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on
2.4 Other Standards:
Conductors of Light Metals.
4
NBS Handbook 100—Copper Wire Tables
Current edition approved March 1, 2018. Published March 2018. Originally
approved in 1982. Last previous edition approved in 2013 as B711 – 13. DOI:
10.1520/B0711-18.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM 4th Floor, New York, NY 10036.
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Institute of Standards and Technology (NIST), 100
the ASTM website. Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B711 − 18
3. Terminology 5. Requirement for Wires
3.1 Definitions of Terms Specific to This Standard: 5.1 Before stranding, the aluminum-alloy wire shall meet
the requirements of Specificat
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B711 − 13 B711 − 18
Standard Specification for
Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel
1
Reinforced (AACSR) (6201)
This standard is issued under the fixed designation B711; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-alloy 6201-T81 hard: solution
heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or
aluminum-clad steel core wire for use as overhead electric conductors (Explanatory Note 1 and Note 2).
NOTE 1—The alloy and temper designations conform to ANSI H35.1. Aluminum alloy 6201 corresponds to Unified Numbering System alloy A96201
in accordance with Practice E527.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein.
2
2.2 ASTM Standards:
B263 Test Method for Determination of Cross-Sectional Area of Stranded Conductors
B354 Terminology Relating to Uninsulated Metallic Electrical Conductors
B398/B398M Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes
B498/B498M Specification for Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors
B500/B500M Specification for Metallic Coated or Aluminum Clad Stranded Steel Core for Use in Overhead Electrical
Conductors
B502 Specification for Aluminum-Clad Steel Core Wire for Use in Overhead Electrical Aluminum Conductors
B606 Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Aluminum and Aluminum-Alloy
Conductors, Steel Reinforced
B802/B802M Specification for Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors,
Steel Reinforced (ACSR)
B803 Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead
Electrical Conductors
B957 Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead
Electrical Conductors
B958 Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated
Steel Core Wire for Use in Overhead Electrical Conductors
1
This specification is under the jurisdiction of ASTM Committee B01 on Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on Conductors
of Light Metals.
Current edition approved Jan. 1, 2013March 1, 2018. Published January 2013March 2018. Originally approved in 1982. Last previous edition approved in 20122013 as
B711 – 12.B711 – 13. DOI: 10.1520/B0711-13.10.1520/B0711-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B711 − 18
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
2.3 American National Standards Institute Standard:
3
H35.1M Alloy and Temper Designation Systems for Aluminum
2.4 Other Standards:
4
NBS Handbook 100—Copper Wire Tables
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 AA
...