ASTM F1741-96

Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits

SCOPE
1.1 This practice describes the procedures for the rehabilitation of sewer lines and conduits, 6 to 48 in. in diameter, by the insertion of a machine-made field-fabricated spiral wound liner pipe into an existing pipeline. After insertion, the spiral wound liner pipe is expanded until it presses against the interior surface of the existing pipeline, or, alternatively, the spiral wound liner pipe is inserted as a fixed diameter into the existing pipeline and is not expanded, and the annular space between the spiral wound liner pipe and the existing pipe is grouted. This rehabilitation process can be used in a variety of gravity applications such as sanitary sewers, storm sewers, culverts, and process piping.
1.2 The values in parentheses are provided for information purposes only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.3.1 Particular attention is drawn to those safety regulations and requirements involving entering into and working in confined spaces.

General Information

• Status: Historical
• Publication Date: 09-Jan-2002
• ICS: 23.040.20 - Plastics pipes
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.67 - Trenchless Plastic Pipeline Technology

Relations

• Replaced By: ASTM F1741-01 - Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits
• Effective Date: 10-Jan-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or
withdrawn. Contact ASTM International (www.astm.org) for the latest information.
Designation: F 1741 – 96
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Practice for
Installation of Machine Spiral Wound Poly (Vinyl Chloride)
(PVC) Liner Pipe for Rehabilitation of Existing Sewers and
1
Conduits
This standard is issued under the fixed designation F 1741; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
4
1. Scope Gravity Sewer Lines Using Low-Pressure Air
F 1697 Specification for Poly (Vinyl Chloride) (PVC) Pro-
1.1 This practice describes the procedures for the rehabili-
file Strip for Machine Spiral Wound Liner Pipe Rehabili-
tation of sewer lines and conduits, 6 to 48 in. in diameter, by
4
tation of Existing Sewers and Conduit
the insertion of a machine-made field-fabricated spiral wound
2.2 NASSCO Standard:
liner pipe into an existing pipeline. After insertion, the spiral
Recommended Specifications for Sewer Collection System
wound liner pipe is expanded until it presses against the
5
Rehabilitation
interior surface of the existing pipeline, or, alternatively, the
2.3 Uni-Bell Standard:
spiral wound liner pipe is inserted as a fixed diameter into the
UNI-B-5-89 Recommended Practice for the Installation of
existing pipeline and is not expanded, and the annular space
6
PVC Sewer Pipe
between the spiral wound liner pipe and the existing pipe is
grouted. This rehabilitation process can be used in a variety of
3. Terminology
gravity applications such as sanitary sewers, storm sewers,
3.1 General—Definitions are in accordance with Termi-
culverts, and process piping.
nologies D 883 and F 412. Abbreviations are in accordance
1.2 The values in parentheses are provided for information
with Terminology D 1600, unless otherwise indicated.
purposes only.
3.2 Definitions of Terms Specific to This Standard:
1.3 This standard does not purport to address all of the
3.2.1 extruded PVC profile strip—a product available in
safety concerns, if any, associated with its use. It is the
various widths, consisting of a smooth inside surface and a
responsibility of the user of this standard to establish appro-
ribbed outer surface with mechanically locked male and female
priate safety and health practices and determine the applica-
edges which are self interlocking, or separate locking strips
bility of regulatory limitations prior to use.
which serve the same purpose (Table 1 and Fig. 1).
1.3.1 Particular attention is drawn to those safety regula-
3.2.2 insertion point—an existing manhole, existing access
tions and requirements involving entering into and working in
shaft, or excavated pit that serves as the point where a winding
confined spaces.
machine field fabricates the spiral wound liner pipe and
2. Referenced Documents simultaneously inserts the spiral wound liner pipe into the
existing pipeline.
2.1 ASTM Standards:
3.2.3 production run—a continuous extrusion of a given
C 39 Test Method for Compressive Strength of Cylindrical
2 profile type.
Concrete Specimens
3
3.2.4 spiral wound liner pipe—a product field fabricated
D 883 Terminology Relating to Plastics
from extruded PVC profile strip to a round shape (see Fig. 2).
D 1600 Terminology for Abbreviated Terms Relating to
3
3.2.5 termination point—an existing manhole, existing ac-
Plastics
cess shaft, or an excavated pit that serves as the point of exit of
D 1784 Specification for Rigid Poly (Vinyl Chloride)
the spiral wound liner pipe from the existing pipe.
(PVC) Compounds and Chlorinated Poly (Vinyl Chloride)
3
(CPVC) Compounds
4. Significance and Use
4
F 412 Terminology Relating To Plastic Piping Systems
4.1 This practice is for use by designers and specifiers,
F 1417 Test Method for Installation Acceptance of Plastic
regulatory agencies, owners, and inspection organizations who
are involved in the rehabilitation of non-pressure sewers and
1
This practice is under the jurisdiction of ASTM Committee F-17 on Plastic
conduits. Modifications may be required for specific job
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
conditions.
Trenchless Plastic Pipeline Technology.
Current edition approved Oct. 10, 1996. Published December 1996.
2
Annual Book of ASTM Standards, Vol 04.07.
3 5
Annual Book of ASTM Standards, Vol 08.01. Available from NASSCO, 140 Circle Drive, Suite 103, Maitland, FL 32751.
4 6
Annual Book of ASTM Standards, Vol 08.04. Available from Uni-Bell, 2655 Villa Creek Drive, Suite 155, Dallas TX 75234.
1

---------------------- Page: 1 ----------------------
F 1741
TABLE 1 Typical Profile Strip Moments of I
...