ASTM F1412-09
(Specification)Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
ABSTRACT
This specification covers the requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems. The pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins (polyethylene and polypropylene) that shall contain suitable stabilizers and antioxidants and may contain pigments and fillers not detrimental to the pipe and fittings. The specimens shall conform to the outside diameter; wall thickness; average waterway diameter; chemical resistance to acetic acid, acetone, methyl alcohol, ammonium hydroxide, nitric acid, and sodium hydroxide; water absorption; system integrity; flattening; and impact resistance requirements. Hydrostatic pressure tests shall be conducted on both the heat-fused and mechanical joints.
SCOPE
1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.
1.2 Pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins, polyethylene (PE) and polypropylene (PP).
1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.4 Pipe and fittings are joined by the heat fusion method (D 2657 and F 1290) or by using mechanical joints recommended by the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following safety hazards caveat pertains only to the test method, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1412 −09
StandardSpecification for
Polyolefin Pipe and Fittings for Corrosive Waste Drainage
1
Systems
This standard is issued under the fixed designation F1412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D543Practices for Evaluating the Resistance of Plastics to
Chemical Reagents
1.1 This specification covers requirements for non-pressure
D570Test Method for Water Absorption of Plastics
polyolefin pipe and fittings for corrosive waste drainage
D618Practice for Conditioning Plastics for Testing
systems.
D1248Specification for Polyethylene Plastics Extrusion
1.2 PipeisproducedinSchedule40and80IPSsizesintwo
Materials for Wire and Cable
polyolefins, polyethylene (PE) and polypropylene (PP).
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
1.3 The interchangeability of pipe and fittings made by
different manufacturers is not addressed in this specification. D2122Test Method for Determining Dimensions of Ther-
moplastic Pipe and Fittings
Transition fittings for joining pipe and fittings of different
manufacturers is provided for in this specification. D2321PracticeforUndergroundInstallationofThermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
1.4 Pipe and fittings are joined by the heat fusion method
D2412Test Method for Determination of External Loading
(D2657 and F1290) or by using mechanical joints recom-
Characteristics of Plastic Pipe by Parallel-Plate Loading
mended by the manufacturer.
D2444Test Method for Determination of the Impact Resis-
1.5 The values stated in inch-pound units are to be regarded
tance of Thermoplastic Pipe and Fittings by Means of a
as standard. The values given in parentheses are mathematical
Tup (Falling Weight)
conversions to SI units that are provided for information only
D2657Practice for Heat Fusion Joining of Polyolefin Pipe
and are not considered standard.
and Fittings
1.6 The following safety hazards caveat pertains only to the D3311Specification for Drain, Waste, and Vent (DWV)
testmethod,Section8,ofthisspecification. This standard does Plastic Fittings Patterns
not purport to address all of the safety concerns, if any, D3350Specification for Polyethylene Plastics Pipe and Fit-
associated with its use. It is the responsibility of the user of this tings Materials
standard to establish appropriate safety and health practices D4101Specification for Polypropylene Injection and Extru-
and determine the applicability of regulatory limitations prior sion Materials
to use. F412Terminology Relating to Plastic Piping Systems
F1290PracticeforElectrofusionJoiningPolyolefinPipeand
2. Referenced Documents
Fittings
2
F1498SpecificationforTaperPipeThreads60°forThermo-
2.1 ASTM Standards:
plastic Pipe and Fittings
2.2 Federal Standard:
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
3
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
2.3 Military Standard:
Current edition approved Jan. 15, 2009. Published January 2009. Originally
ε1
3
approved in 1992. Last previous edition approved in 2001 as F1412–01 . DOI:
MIL-STD-129Marking for Shipment and Storage
10.1520/F1412-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1412−09
TABLE 1 Outside Diameters and Tolerances for Polyolefin Pipe
2.4 Other Document:
4 Schedules 40 and 80, in. (mm)
Uniform Plumbing Code
Nominal Average Out-of-Roundness
Pipe Outside Tolerance (maximum minus
3. Terminology
Size Diameter minimum)
1
3.1 Definitions:
1 ⁄4 1.660 (42.16) ±0.005 (±0.13) 0.050 (1.27)
A
1
1 ⁄2 1.750 (44.45) ±0.010 (±0.25) 0.060 (1.52)
3.1.1 Definitionsusedinthisspecificationareinaccordance
1
1 ⁄2 1.900 (48.26) ±0.006 (±0.15) 0.060 (1.52)
with the definitions given in Terminology F412, and abbrevia-
2 2.375 (60.32) ±0.006 (±0.15) 0.070 (1.78)
tions are in accordance with Terminology D1600, unless
3 3.500 (88.90) ±0.008 (±0.20) 0.080 (2.03)
4 4.500 (114.30) ±0.009 (±0.23) 0.100 (2.54)
otherwise indicated.
6 6.625 (16
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
´1
Designation:F 1412–01 Designation: F 1412 – 09
Standard Specification for
Polyolefin Pipe and Fittings for Corrosive Waste Drainage
1
Systems
This standard is issued under the fixed designation F 1412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Supplementary Requirements section was editorially updated in December 2002.
1. Scope*
1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.
1.2This specification 1.2 Pipe is a companion to the Canadian Standard, CAN/CSA-B181.3.
1.3Pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins, polyethylene (PE) and polypropylene (PP).
1.4The1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification.
Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.5Pipe1.4 Pipe and fittings are joined by the heat fusion method (D2657 and F1290) or by using mechanical joints
recommended by the manufacturer.
1.6The values stated in inch-pound units are to be regarded as the standard.The values in parentheses are given for information
only.
1.7
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 Thefollowingsafetyhazardscaveatpertainsonlytothetestmethod,Section8,ofthisspecification. This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D543 Test Method Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D570 Test Method for Water Absorption of Plastics
3
D618 Practice for Conditioning Plastics and Electrical Insulating Materials for Testing Practice for Conditioning Plastics for
Testing
3
D1248 Specification for Polyethylene Plastics Molding and Extrusion Materials Specification for Polyethylene Plastics
Extrusion Materials for Wire and Cable
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Flexible Thermoplastic Pipe for Sewers and Other Gravity-FlowApplications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falling
Weight)
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4101 Specification for Propylene Plastic Polypropylene Injection and Extrusion Materials
F412 Terminology Relating to Plastic Piping Systems
F1290 Practice for Electrofusion Joining Polyolefin Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved April 10, 2001. Published June 2001. Originally published as F1412–92. Last previous edition F1412–00.
´1
Current edition approved Jan. 15, 2009. Published January 2009. Originally approved in 1992. Last previous edition approved in 2001 as F1412–01 .
2
Available from the Canadian Standards Association, 178 Rexdale Boulevard, Rexdale (Toronto), Ontario, Canada M9W 1R3.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1412 – 09
F1498 Specification for Taper Pipe Threads 60°60 for T
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
´1
Designation:F 1412–01 Designation: F 1412 – 09
Standard Specification for
Polyolefin Pipe and Fittings for Corrosive Waste Drainage
1
Systems
This standard is issued under the fixed designation F 1412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Supplementary Requirements section was editorially updated in December 2002.
1. Scope*
1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.
1.2This specification 1.2 Pipe is a companion to the Canadian Standard, CAN/CSA-B181.3.
1.3Pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins, polyethylene (PE) and polypropylene (PP).
1.4The1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification.
Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.5Pipe1.4 Pipe and fittings are joined by the heat fusion method (D2657 and F1290) or by using mechanical joints
recommended by the manufacturer.
1.6The values stated in inch-pound units are to be regarded as the standard.The values in parentheses are given for information
only.
1.7
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 Thefollowingsafetyhazardscaveatpertainsonlytothetestmethod,Section8,ofthisspecification. This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D543 Test Method Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D570 Test Method for Water Absorption of Plastics
3
D618 Practice for Conditioning Plastics and Electrical Insulating Materials for Testing Practice for Conditioning Plastics for
Testing
3
D1248 Specification for Polyethylene Plastics Molding and Extrusion Materials Specification for Polyethylene Plastics
Extrusion Materials for Wire and Cable
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Flexible Thermoplastic Pipe for Sewers and Other Gravity-FlowApplications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falling
Weight)
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4101 Specification for Propylene Plastic Polypropylene Injection and Extrusion Materials
F412 Terminology Relating to Plastic Piping Systems
F1290 Practice for Electrofusion Joining Polyolefin Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved April 10, 2001. Published June 2001. Originally published as F1412–92. Last previous edition F1412–00.
´1
Current edition approved Jan. 15, 2009. Published January 2009. Originally approved in 1992. Last previous edition approved in 2001 as F1412–01 .
2
Available from the Canadian Standards Association, 178 Rexdale Boulevard, Rexdale (Toronto), Ontario, Canada M9W 1R3.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1412 – 09
F1498 Specification for Taper Pipe Threads 60°60 for T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.