EN 1677-3:2001
(Main)Components for slings - Safety - Part 3: Forged steel self-locking hooks - Grade 8
Components for slings - Safety - Part 3: Forged steel self-locking hooks - Grade 8
This European Standard specifies requirements for forged steel self-locking lifting hooks of Grade 8 having eye or clevis and pin up to 21,2 t working load limit (WLL), mainly for use in:
- chain slings according to EN 818-4
- steel wire rope slings according to prEN 13414-1
- textile slings according to EN 1492-1, EN 1492-2 .
intended for lifting objects, materials or goods.
The hazards covered by this part of EN 1677 are identified in clause 4.
Annex A gives the bases for calculation of hook dimensions.
Annex B gives an example of a designation systems for hooks of Grade 8.
Einzelteile für Anschlagmittel - Sicherheit - Teil 3: Geschmiedete, selbstverriegelnde Haken - Güteklasse 8
Diese Europäische Norm legt Anforderungen für selbstverriegelnde, geschmiedete Haken aus Stahl der Güte-klasse 8 mit Ösen oder als Gabelkopfhaken im Bereich bis 21,2 t Tragfähigkeit fest, die hauptsächlich Verwendung finden in:
¾ Anschlagketten nach EN 818-4;
¾ Anschlagseilen aus Stahldraht nach prEN 13414-1 und
¾ textilen Anschlagmitteln nach EN 1492-1 und EN 1492-2,
die zum Heben von Gegenständen, Materialien und Gütern vorgesehen sind.
Die Gefährdungen, die durch diesen Teil von EN 1677 abgedeckt werden, sind in Abschnitt 4 aufgeführt.
Anhang A enthält Grundlagen für die Berechnung der Hakenmaße.
Anhang B enthält ein Beispiel eines Bezeichnungssystems für Haken der Güteklasse 8.
Accessoires pour élingues - Sécurité - Partie 3: Crochets autobloquants en acier forgé - Classe 8
La présente Norme européenne spécifie les prescriptions générales requises pour les crochets en acier forgé à ¿il ou à chape de classe 8 de charge maximale d'utilisation (WLL) inférieure ou égale à 21,2 t principalement utilisés avec :
¾ des élingues en chaînes selon l'EN 818-4 ;
¾ des élingues en câbles d'acier selon le prEN 13414-1 ;
¾ des élingues textiles selon l'EN 1492-1 et l'EN 1492-2 ;
prévues pour le levage d'objets, de matériels ou de marchandises.
Les phénomènes dangereux couverts par la présente partie de l'EN 1677 sont identifiés dans l'article 4.
L'annexe A indique les bases de calcul des dimensions des crochets.
L'annexe B donne un exemple de système de désignation des crochets de classe 8.
Sestavni deli obes - Varnost - 3. del: Kovani jekleni samozapiralni kavlji - Kakovostni razred 8
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1677-3:2002
01-maj-2002
Sestavni deli obes - Varnost - 3. del: Kovani jekleni samozapiralni kavlji -
Kakovostni razred 8
Components for slings - Safety - Part 3: Forged steel self-locking hooks - Grade 8
Einzelteile für Anschlagmittel - Sicherheit - Teil 3: Geschmiedete, selbstverriegelnde
Haken - Güteklasse 8
Accessoires pour élingues - Sécurité - Partie 3: Crochets autobloquants en acier forgé -
Classe 8
Ta slovenski standard je istoveten z: EN 1677-3:2001
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
SIST EN 1677-3:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 1677-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2001
ICS 53.020.30
English version
Components for slings - Safety - Part 3: Forged steel self-
locking hooks - Grade 8
Accessoires pour élingues - Sécurité - Partie 3: Crochets Einzelteile für Anschlagmittel - Sicherheit - Teil 1:
autobloquants en acier forgé - Classe 8 Geschmiedete, selbstverriegelnde Haken - Güteklasse 8
This European Standard was approved by CEN on 11 August 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1677-3:2001 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 1677-3:2001 (E)
Contents
page
Foreword 3
1 Scope 4
2 Normative references 5
3 Terms and definitions 5
4 Significant hazards 6
5 Safety requirements 7
6 Verification of safety requirements 10
7 Marking 12
8 Manufacturer’s certificate 12
9 Information for use 12
Annex A (informative) Bases for the calculation of hook dimensions 13
Annex B (informative) Designation system for self locking hooks - grade 8 14
Annex ZA (informative) Relationship of this document with EC Directives 15
2
---------------------- Page: 3 ----------------------
EN 1677-3:2001 (E)
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 168, “Chains, ropes,
webbing, slings and accessories - Safety” the Secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2002, and conflicting national standards shall
be withdrawn at the latest by March 2002.
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EC
Directive(s).
For the relationship with EC Directives, see informative annex ZA, which is an integral part of this
standard.
This European Standard is a part of a products standard related to safety for components for slings.
The other Parts of EN 1677 for components for slings are:
Part 1: Forged steel components - Grade 8
Part 2: Forged steel lifting hooks with latch - Grade 8
Part 4: Links - Grade 8
Part 5: Forged steel lifting hooks with latch - Grade 4
Part 6: Links - Grade 4
This is the first edition of this Part of EN 1677.
Annexes A and B of this European Standard are informative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 4 ----------------------
EN 1677-3:2001 (E)
Introduction
This European Standard has been prepared to be a harmonized standard providing one means of
complying with the essential safety requirements of the Machinery Directive and associated EFTA
regulations.
The hooks covered by this Part of EN 1677 are normally supplied to be part of a sling, but they may
also be used for other applications. In such instances it is important that the hook design is checked to
ensure its fitness for the intended use.
The extent to which hazards are covered is indicated in the scope. In addition, lifting equipment shall
conform as appropriate to EN 292 for hazards that are not covered by this standard.
1 Scope
This European Standard specifies requirements for forged steel self-locking lifting hooks of Grade 8
having eye or clevis and pin up to 21,2 t working load limit (WLL), mainly for use in:
– chain slings according to EN 818-4
– steel wire rope slings according to prEN 13414-1
– textile slings according to EN 1492-1, EN 1492-2 .
intended for lifting objects, materials or goods.
The hazards covered by this part of EN 1677 are identified in clause 4.
Annex A gives the bases for calculation of hook dimensions.
Annex B gives an example of a designation systems for hooks of Grade 8.
4
---------------------- Page: 5 ----------------------
EN 1677-3:2001 (E)
2 Normative references
This European Standard incorporates by dated or undated reference provisions form other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this European Standard only when incorporated in it by amendment or revision. For undated
references the latest edition of the publication referred to applies (including amendments).
EN 292-2:1991/A1:1995 Safety of machinery - Basic concepts, general principles for design - Part 2:
Technical principles and specifications (Amendment 1:1995)
EN 818-4 Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
EN 818-6 Short link chain for lifting purposes - Safety - Part 6: Chain slings -
Specification for information for use and maintenance to be provided by the
manufacturer
EN 1050:1996 Safety of machinery - Principles for risk assessment
EN 1492-1 Textile slings - Safety - Part 1: Flat woven webbing slings, made of man-
made fibres, for general purpose use
EN 1492-2 Textile slings - Safety - Part 2: Roundslings, made of man-made fibres, for
general purpose use
EN 1677-1:2000 Components for slings - Safety - Part 1: Forged steel components, Grade 8
prEN 13414-1 Steel wire rope slings - Safety - Part 1: Wire rope slings
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 1677-1 apply, together
with the following.
3.1
self-locking hook:
hook containing a locking mechanism, capable of being activated by the action of the load which, once
correctly closed and locked, can only be opened in the unloaded condition by de-activation of the locking
mechanism
5
---------------------- Page: 6 ----------------------
EN 1677-3:2001 (E)
4 Significant hazards
Accidental release of a load or release of a load due to failure of a hook puts at risk, either directly or
indirectly, the safety or health of those persons within the danger zone.
In order to provide the necessary strength and durability of hooks this Part of EN 1677 gives
requirements for the design, manufacture and testing to ensure the specified levels of performance are
met.
Since failure can be caused by the incorrect choice of grade and specification of hook, this Part of EN
1677 also gives requirements for marking and the manufacturer's certificate.
Errors of fitting can also lead to failure and this Part of EN 1677 contains dimensional requirements to
allow correct fit.
Risk of injury due to sharp edges, sharp angles or rough surfaces when handling is also covered by this
standard.
Those aspects of safe use associated with good practice are given in EN 818-6.
Table 1 contains those hazards which require action to reduce risk identified by risk assessment as being
specific and significant for forged steel self-locking hooks of grade 8.
Table 1 - Significant hazards and associated requirements
Hazards identified in accordance Relevant clause of Relevant clause /
with annex A of EN 1050:1996 annex A of EN 292-2: subclause of this Part of
1991/A1:1995 EN 1677
1.e Mechanical hazard 1.3.2 5
due to inadequacy of 4.1.2.3 5
strength 4.1.2.5 5
4.2.4 5
1.7.3 7
1.3 Cutting hazard 1.3.4 5.4
1.8 Friction or abrasion 1.3.4 5.4
hazard
15 Errors of fitting hazard 1.5.4 5.2
6
---------------------- Page: 7 ----------------------
EN 1677-3:2001 (E)
5 Safety requirements
5.1 Design
The articulation and relative movement shall be in accordance with 5.1 of EN 1677-1:2000.
NOTE 1 The form of the hook is not specified in detail. For example, a minimum value of
dimension F (see Figure 1) as measured in any direction is specified so that the eye of the hook
can accommodate a pin, but the eye of the hook need not be circular.
The form of the upper end shall be either of the eye type or the clevis type as designated in Table 2.
A closed hook in the finished condition shall be able to withstand a bend test in accordance with 6.2.2
(
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.