EN 3475-704:2007
(Main)Aerospace series - Cables, electrical, aircraft use - Test methods - Part 704: Flexibility
Aerospace series - Cables, electrical, aircraft use - Test methods - Part 704: Flexibility
This standard specifies two methods for appraising the flexibility of a completed cable and its bending aptitude, Method 1 is for cables not less than 5 mm2 cross-section cables and Method 2 for cables not larger than 5 mm2 (10 AWG) cross-section cables.
Unless otherwise specified in the product standard, Method 1 applies.
It shall be used together with EN 3475-100.
Luft- und Raumfahrt - Elektrische Leitungen für Luftfahrtverwendung - Prüfverfahren - Teil 704: Biegsamkeit
Diese Norm legt zwei Verfahren zur Bewertung der Biegsamkeit einer fertigen Leitung und deren Biegbarkeit fest, Verfahren 1 gilt für Leitungen mit einem Querschnitt von mehr als 5 mm2 und Verfahren 2 für Leitungen mit einem Querschnitt von oder von unter 5 mm2 (AWG-Größe 10).
Es gilt Verfahren 1, falls nicht anders in der Produktnorm festgelegt.
Die Norm ist in Verbindung mit EN 3475 100 anzuwenden.
Série aérospatiale - Câbles électriques à usage aéronautique - Méthodes d'essais - Partie 704 : Flexibilité
Aeronavtika - Električni kabli za uporabo v zračnih plovilih - Preskusne metode - 704. del: Prožnost
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Cables, electrical, aircraft use - Test methods - Part 704: FlexibilitySérie aérospatiale - Câbles électriques a usage aéronautique - Méthodes d'essais - Partie 704 : FlexibilitéLuft- und Raumfahrt - Elektrischen Leitungen für Luftfahrt Verwendung - Prüfverfahren - Teil 704: BiegsamkeitTa slovenski standard je istoveten z:EN 3475-704:2007SIST EN 3475-704:2007en49.060Aerospace electric equipment and systemsICS:SIST EN 3475-704:20041DGRPHãþDSLOVENSKI
STANDARDSIST EN 3475-704:200701-november-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3475-704August 2007ICS 49.060Supersedes EN 3475-704:2002
English VersionAerospace series - Cables, electrical, aircraft use - Testmethods - Part 704: FlexibilitySérie aérospatiale - Câbles électriques à usageaéronautique - Méthodes d'essais - Partie 704 : FlexibilitéLuft- und Raumfahrt - Elektrischen Leitungen für LuftfahrtVerwendung - Prüfverfahren - Teil 704: BiegsamkeitThis European Standard was approved by CEN on 21 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3475-704:2007: E
EN 3475-704:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Test Procedures.4
EN 3475-704:2007 (E) 3 Foreword This document (EN 3475-704:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn at the latest by February 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 3475-704:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 3475-704:2007 (E) 4 1 Scope This standard specifies two methods for appraising the flexibility of a completed cable and its bending aptitude, Method 1 is for cables not less than 5 mm2 cross-section cables and Method 2 for cables not larger than 5 mm2 (10 AWG) cross-section cables.
Unless otherwise specified in the product standard, Method 1 applies. It shall be used together with EN 3475-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.