EN 932-5:2012
(Main)Tests for general properties of aggregates - Part 5: Common equipment and calibration
Tests for general properties of aggregates - Part 5: Common equipment and calibration
This European Standard specifies general requirements for common equipment, calibration and checking procedures and reagents for the testing of the properties of aggregates.
In the case of checking, other procedures than the ones described in this standard may be used provided that appropriate working relationships with the corresponding methods described in this standard have been established. In case of dispute, the checking methods described in this standard shall be used.
Prüfverfahren für allgemeine Eigenschaften von Gesteinskörnungen - Teil 5: Allgemeine Prüfeinrichtungen und Kalibrierung
Diese Europäische Norm legt allgemeingültige Anforderungen an die gebräuchlichen Prüfeinrichtungen,
Kalibrierungs- und Überprüfungsverfahren und Reagenzien für die Prüfung der Eigenschaften von Gesteinskörnungen
fest.
Bei Überprüfungen dürfen auch andere Verfahren, als die in dieser Norm beschriebenen, angewendet
werden, sofern ein ausreichender Zusammenhang mit den entsprechenden in dieser Norm beschriebenen
Verfahren nachgewiesen wurden. Bei Streitfällen sind die in dieser Norm beschriebenen Überprüfungsverfahren
anzuwenden.
Essais pour déterminer les propriétés générales des granulats - Partie 5: Equipements communs et étalonnage
La présente norme européenne spécifie les prescriptions générales concernant les équipements communs,
les procédures d'étalonnage et les réactifs utilisés pour les essais destinés à déterminer les propriétés des
granulats.
Dans des cas de vérification, d’autres procédures que celles décrites dans la présente norme peuvent être
utilisées à condition que des relations de fonctionnement convenables soient établies avec les méthodes
correspondantes décrites dans la présente norme. En cas de litige, les méthodes de vérification décrites dans
la présente norme doivent être utilisées.
Preskusi splošnih lastnosti agregatov - 5. del: Splošne zahteve za opremo in kalibracijo
Ta evropski standard določa splošne zahteve za splošno opremo, kalibracijske postopke in reagente za preskušanje lastnosti agregatov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2012
1DGRPHãþD
SIST EN 932-5:2000
Preskusi splošnih lastnosti agregatov - 5. del: Splošne zahteve za opremo in
kalibracijo
Tests for general properties of aggregates - Part 5: Common equipment and calibration
Prüfverfahren für allgemeine Eigenschaften von Gesteinskömungen - Teil 5: Allgemeine
Prüfeinrichtungen und Kalibrierung
Essais pour déterminer les propriétés générales des granulats - Partie 5: Equipments
communs et étalonnage
Ta slovenski standard je istoveten z: EN 932-5:2012
ICS:
91.100.15 Mineralni materiali in izdelki Mineral materials and
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 932-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2012
ICS 91.100.15 Supersedes EN 932-5:1999
English Version
Tests for general properties of aggregates - Part 5: Common
equipment and calibration
Essais pour déterminer les propriétés générales des Prüfverfahren für allgemeine Eigenschaften von
granulats - Partie 5: Equipements communs et étalonnage Gesteinskörnungen - Teil 5: Allgemeine Prüfeinrichtungen
und Kalibrierung
This European Standard was approved by CEN on 30 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 932-5:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .5
4 Common equipment .5
4.1 Tolerances .5
4.1.1 Manufacturing tolerances .5
4.1.2 Working tolerances.6
4.2 Measuring instruments .6
4.2.1 General .6
4.2.2 Balances and weights .6
4.2.3 Thermometers .7
4.2.4 Dimensional measurement instruments .7
4.2.5 Timers .8
4.2.6 Volumetric glassware .8
4.2.7 Density hydrometers .8
4.3 Other instruments .8
4.3.1 Ovens .8
4.3.2 Constant temperature bath .8
4.3.3 Test sieves and bar sieves .8
4.3.4 Moulds and drums .8
4.3.5 Sieve shakers .9
4.3.6 Desiccators and desiccator cabinets .9
4.3.7 Bottle shakers and rollers .9
4.3.8 Heaters .9
4.3.9 Rotating machinery .9
4.3.10 Vibrating machinery .9
4.3.11 Pressure or vacuum .9
5 Calibration and checking .9
5.1 Calibration of reference standards and reference instruments .9
5.1.1 Laboratory reference standards .9
5.1.2 Specifications for reference standards and reference instruments . 10
5.2 Calibration and checking of test equipment . 11
5.2.1 Traceability . 11
5.2.2 External and in-house calibration . 11
5.2.3 Calibration and checking of measuring instruments . 12
5.2.4 Checking of other instruments . 14
6 Reagents . 17
6.1 Distilled water . 17
6.2 Chemical reagents . 18
Annex A (normative) Method for the performance check of sieves . 19
Annex B (normative) Procedure for the manual checking of perforated plate test sieve openings . 22
B.1 Equipment for checking the openings of plate test sieves . 22
B.2 Calibration of sieve check gauges . 22
B.3 Test procedure . 22
Annex C (informative) Balance recommendation for various standard test methods . 24
Bibliography . 25
Foreword
This document (EN 932-5:2012) has been prepared by Technical Committee CEN/TC 154 “Aggregates”, the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at
the latest by August 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 932-5:1999.
This standard forms part of a series of standards for general properties of aggregates. Test methods for other
properties of aggregates are covered by the following European Standards:
EN 933, Tests for geometrical properties of aggregates;
EN 1097, Tests for mechanical and physical properties of aggregates;
EN 1367, Tests for thermal and weathering properties of aggregates;
EN 1744, Tests for chemical properties of aggregates;
EN 13179, Tests for filler aggregate used in bituminous mixtures.
The other parts of EN 932, Tests for general properties of aggregates are:
Part 1: Methods for sampling;
Part 2: Methods for reducing laboratory samples;
Part 3: Procedure and terminology for simplified petrographic description;
Part 6: Definitions of repeatability and reproducibility.
In the bibliography, reference is made to the International Organization for Legal Metrology (OIML)
classification, which this standard has adopted for the purposes of establishing a frequency of calibration for
balance weights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
1 Scope
This European Standard specifies general requirements for common equipment, calibration and checking
procedures and reagents for the testing of the properties of aggregates.
In the case of checking, other procedures than the ones described in this standard may be used provided that
appropriate working relationships with the corresponding methods described in this standard have been
established. In case of dispute, the checking methods described in this standard shall be used.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 933-1, Tests for geometrical properties of aggregates — Part 1: Determination of particle size
distribution — Sieving method
EN 933-2, Tests for geometrical properties of aggregates — Part 2: Determination of particle size
distribution — Test sieves, nominal size of apertures
EN 933-3, Tests for geometrical properties of aggregates — Part 3: Determination of particle shape —
Flakiness index
EN 933-8, Tests for geometrical properties of aggregates — Part 8: Assessment of fines — Sand equivalent
test
EN ISO 3650, Geometrical product specifications (GPS) — Length standards — Gauge blocks
(ISO 3650:1998)
ISO 384, Laboratory glassware — Principles of design and construction of volumetric glassware
ISO 386, Liquid-in-glass laboratory thermometers — Principles of design, construction and use
ISO 649-1, Laboratory glassware — Density hydrometers for general purposes — Part 1: Specification
ISO 3310-1, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth
ISO 3310-2, Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal
plate
ISO 4788, Laboratory glassware — Graduated measuring cylinders
ISO 6353-2, Reagents for chemical analysis — Part 2: Specifications —- First series
ISO 6353-3, Reagents for chemical analysis — Part 3: Specifications — Second series
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
calibration
operation that, under specified conditions, in a first step, establishes a relation between the quantity values with
measurement uncertainties provided by measurement standards and corresponding indications with associated
measurement
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.