EN 13071-1:2019
(Main)Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General requirements
Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General requirements
This document specifies requirements of stationary containers, top lifted and bottom emptied, used for collection of solid non-hazardous wastes, with capacity up to 5 000 l.
This document specifies general characteristics of such containers and their accessories, test methods and safety requirements as well as recommendations for installation, maintenance and cleaning operations.
Stationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und Bodenentleerung - Teil 1: Allgemeine Anforderungen
Dieses Dokument legt Anforderungen an stationäre Abfallsammelbehälter mit einem Volumen bis 5 000 l, mit Behälteraufnahme an der Oberseite und Bodenentleerung, für die Sammlung von festen, nicht gefährlichen Abfallstoffen fest.
Dieses Dokument legt allgemeine Eigenschaften solcher Behälter und deren Zubehör, Prüfverfahren und Sicherheitsanforderungen sowie Empfehlungen zur Installation, Instandhaltung und Reinigung fest.
Conteneurs fixes à déchets de capacité inférieure ou égale à 5 000 l, levés par le haut et vidés par le bas - Partie 1 : Exigences générales
Le présent document spécifie les exigences qui s’appliquent aux conteneurs fixes, levés par le haut et vidés par le bas, utilisés pour la collecte de déchets solides non dangereux, d’une capacité maximale de 5 000 l.
Le présent document spécifie les caractéristiques générales de ce type de conteneurs et de leurs accessoires, les méthodes d’essai et les exigences de sécurité qui leur sont applicables, ainsi que des recommandations pour les opérations d’installation, de maintenance et de nettoyage.
Nepremični zabojniki za odpadke do 5000 l, ki se dvigujejo zgoraj in praznijo spodaj - 1. del: Splošne zahteve
Ta dokument določa zahteve za nepremične zabojnike, ki se dvigujejo zgoraj in praznijo spodaj ter se uporabljajo za
zbiranje trdih nenevarnih odpadkov s kapaciteto do 5000 l.
Ta dokument določa splošne lastnosti takih zabojnikov in dodatkov, preskusne metode in varnostne zahteve ter priporočila za namestitev, vzdrževanje in čiščenje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST EN 13071-1:2008
SIST EN 13071-1:2008/AC:2010
Nepremični zabojniki za odpadke do 5000 l, ki se dvigujejo zgoraj in praznijo
spodaj - 1. del: Splošne zahteve
Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General
requirements
Stationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und
Bodenentleerung - Teil 1: Allgemeine Anforderungen
Conteneurs fixes à déchets de capacité inférieure ou égale à 5000 l, levés par le haut et
vidés par le bas - Partie 1 : Exigences générales
Ta slovenski standard je istoveten z: EN 13071-1:2019
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13071-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 13.030.40 Supersedes EN 13071-1:2008
English Version
Stationary waste containers up to 5 000 l, top lifted and
bottom emptied - Part 1: General requirements
Conteneurs fixes à déchets de capacité inférieure ou Stationäre Abfallsammelbehälter bis 5 000 l, mit
égale à 5 000 l, levés par le haut et vidés par le bas - Behälteraufnahme an der Oberseite und
Partie 1 : Exigences générales Bodenentleerung - Teil 1: Allgemeine Anforderungen
This European Standard was approved by CEN on 19 May 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13071-1:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirements . 8
4.1 Recommendations . 8
4.2 Design . 9
4.3 Filling apertures . 9
4.4 Total height . 10
4.5 External surfaces/edges . 10
4.6 Lifting connection position . 10
4.7 Total permissible mass . 10
4.8 Total usable volume . 10
4.9 Waste spillage . 10
5 Test conditions . 10
5.1 General . 10
5.2 Temperature requirements . 10
5.3 Waste density . 10
6 Test methods . 11
6.1 General . 11
6.2 Test methods on empty containers . 11
6.2.1 Stability test (not applicable for flexible containers) . 11
6.2.2 Resistance to interior impacts (not applicable for flexible containers) . 11
Figure 1 — Description of the guiding tube and its position 1 according to the slope of the
filling aperture . 12
Figure 2 — Slant of positions 2 and 5 in relation to position 1 . 13
6.2.3 Free fall test . 13
6.2.4 Resistance of the roof . 14
6.3 Tests methods on loaded containers . 14
6.3.1 Resistance to exterior impacts (not applicable for flexible containers) . 14
Figure 3 — Exterior impact test using the incline plan (informative) . 15
Figure 4 — Determination of lateral impact directions according to the shapes of the
containers . 16
6.3.2 Emptying device/Locking system (not applicable to flexible containers) . 16
6.3.3 Mechanical resistance of the lifting components . 17
6.4 Measurement of the sound level emitted by falling glass inside the containers . 18
6.5 Components treated against corrosion and aging . 18
6.6 Weathering and aging (for thermoplastics only) . 18
6.6.1 Requirement . 18
6.6.2 Procedure. 19
6.7 Sequence of tests . 19
Table 1 — Sequence of the tests (when applicable) . 19
7 Data sheet . 20
8 Marking . 20
9 Test report . 20
Annex A (normative) Weathering test . 21
Bibliography . 22
European foreword
This document (EN 13071-1:2019) has been prepared by Technical Committee CEN/TC 183 “Waste
management”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13071-1:2008.
The main changes compared to the previous edition are listed below:
a) addition of an introduction;
b) addition of terminological entries for "container" (3.1), "flexible container" (3.17) and
"mechatronics" (3.18), while former entries for "type A-container" (3.15) and "type B-container"
were deleted;
c) addition of a new sub clause 4.1 "Recommendations" for installation, maintenance and cleaning of a
container;
d) alignment of the scope according to 4.1;
e) splitting up requirements for design of containers (4.2) and filling apertures (4.3) and addition of
further requirements for filling apertures depending on their height;
f) inclusion of a requirement in 4.6 that the lifting connection shall be positioned so that it can be
lifted from any direction;
g) addition of indications in clause 6 on which test methods apply to flexible containers.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Introduction
According to the European health and safety requirements, work equipment are designed and
constructed so that it can be operated without putting persons at risk. The manufacturer has to
consider the intended conditions of use, but also any reasonably foreseeable misuse.
For that purpose the manufacturer carries out a risk analysis in order to determine the hazards which
the operators and users are exposed to. The equipment will then be designed and constructed taking
into account the results of this assessment, by an iterative process of risk assessment and risk
reduction.
As specified in the guidance document "Classification of equipment used for lifting loads with lifting
machinery" (Machinery Working Group — January 2012), containers used for collecting and lifting bulk
material are not covered by Directive 2006/42/EC [1].
However, a large number of the hazards which the operators using such equipment and the persons
present in the vicinity of lifting/handling operations are exposed to are the same as those resulting
from the use of lifting appliances proper.
These are the reasons why CEN/TC 183 decided to include into this standard requirements intended to
support the corresponding essential health and safety requirements of Directive 2006/42/EC [1], in
particular those related to lifting operations (part 4 of Annex I).
1 Scope
This document specifies requirements of stationary containers, top lifted and bottom emptied, used for
collection of solid non-hazardous wastes, with capacity up to 5 000 l.
This document specifies general characteristics of such containers and their accessories, test methods
and safety requirements as well as recommendations for installation, maintenance and cleaning
operations.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this documen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.