iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

FprEN 1705

(Main)

Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow

Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow

This document specifies a test method for determining the leaktightness and the ease of operation of a valve made of thermoplastic material following an impact applied to the operating device.
Additionally, a different procedure of the test on diaphragm valve can be specified by the valve manufacturer.

Kunststoff-Rohrleitungssysteme - Thermoplast-Armaturen - Prüfverfahren der Unversehrtheit einer Armatur nach äußerer Schlagbelastung

Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Dichtheit und der Leichtgängigkeit einer Armatur aus thermoplastischem Werkstoff nach einem Schlag auf die Betätigungsvorrichtung fest.
Der Hersteller der Armatur kann zusätzlich ein anderes Verfahren zur Prüfung des Membranventils festlegen.

Systèmes de canalisations en plastique - Robinets en thermoplastiques - Méthode d'essai pour la vérification d'un robinet après un choc externe

Le présent document spécifie une méthode d’essai pour déterminer l’étanchéité et la facilité de manoeuvre d’un robinet fabriqué en matière thermoplastique à la suite d’un choc appliqué au dispositif de manoeuvre.
En outre, un mode opératoire différent de l'essai sur un robinet à membrane peut être spécifié par le fabricant de robinet.

Cevni sistemi iz polimernih materialov - Plastomerni ventili - Metoda za preskus neoporečnosti ventila po zunanjem udarcu

General Information

Status
Not Published
Publication Date
07-May-2025
ICS
23.060.01 - Valves in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 32 - Valves
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
14-Nov-2024
Due Date
28-May-2025
Completion Date
14-Nov-2024
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Ref Project
oSIST prEN 1705:2024 - Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow

Relations

Revises
EN 1705:1996 - Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
Effective Date
11-Oct-2023

Buy Standard

prEN 1705:2024prEN 1705:2024
PreviousNext
Draft
prEN 1705:2024
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2024
Cevni sistemi iz polimernih materialov - Plastomerni ventili - Metoda za preskus
neoporečnosti ventila po zunanjem udarcu
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve
after an external blow
Kunststoff-Rohrleitungssysteme - Thermoplast-Armaturen - Prüfverfahren der
Unversehrtheit einer Armatur nach äußerer Schlagbelastung
Systèmes de canalisations en plastique - Robinets en thermoplastiques - Méthode
d'essai pour la vérification d'un robinet après un choc externe
Ta slovenski standard je istoveten z: prEN 1705
ICS:
23.060.01 Ventili na splošno Valves in general
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
prEN 1705
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2024
ICS 23.060.01 Will supersede EN 1705:1996
English Version
Plastics piping systems - Thermoplastics valves - Test
method for the integrity of a valve after an external blow
Systèmes de canalisations en plastique - Robinets en Kunststoff-Rohrleitungs system - Thermoplast-
thermoplastiques - Méthode d'essai pour la vérification Armaturen - Prüfverfahren der Unversehrtheit einer
d'un robinet après un choc externe Armatur nach äußerer Schlagbelastung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1705:2024 E
worldwide for CEN national Members.

prEN 1705:2024 (E)
Contents Page
EUROPEAN FOREWORD . 3
1 SCOPE . 4
2 NORMATIVE REFERENCES . 4
3 TERMS AND DEFINITIONS . 4
4 PRINCIPLE . 5
5 APPARATUS . 7
6 TEST PIECE . 8
6.1 SAMPLING . 8
6.2 PREPARATION OF TEST PIECES . 9
6.3 NUMBER OF TEST PIECES . 9
7 PROCEDURE . 9
7.1 GENERAL . 9
7.2 ASSESSMENT OF OPERATING TORQUE AT −20 °C . 9
7.3 ASSESSMENT OF THE RESISTANCE OF THE STOP MECHANISM AT −20 °C . 9
7.4 ASSESSMENT OF OPERATING TORQUE AT 40 °C . 9
7.5 ASSESSMENT OF THE RESISTANCE OF THE STOP MECHANISM AT 40 °C . 10
7.6 ASSESSMENT OF EXTERNAL LEAKTIGHTNESS . 10
8 TEST REPORT . 10
BIBLIOGRAPHY . 11

prEN 1705:2024 (E)
European foreword
This document (prEN 1705:2024) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 1705:1996.
prEN 1705:2024 includes the following significant technical changes with respect to EN 1705:1996:
— added in the scope the reference to thermoplastic materials
— added the Clause 3 Terms and definitions
— clarifications were introduced for Clause 4 Principle by adding the high-risk impact positions
— subclauses on “Sampling”, “Preparation of test pieces”, “Number of test pieces” were added under
clause “Test piece”
— Clause 7 “Procedure” was revised and operations to be carried out in the tests have been specified
prEN 1705:2024 (E)
1 Scope
This document specifies a test method for determining the leaktightness and the ease of operation of a
valve made of thermoplastic material following an impact applied to the operating device.
Additionally, a different procedure of the test on diaphragm valve can be specified by the valve
manufacturer.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 3127, Thermoplastics pipes - Determination of resistance to external blows - Round-the-clock
method (ISO 3127)
EN ISO 1167-1:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids -
Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
FprEN ISO 8233, Thermoplastics valves - Torque - Test method (ISO/DIS 8233)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org
3.1
operating device
part of a valve for connection with the operating key wh
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
SIST EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial applications.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.4. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [2].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 12201-2 and EN 12201-3 respectively.
Valves made from materials other than PE, conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, conforming to EN 12201-3, or material transition joints (e.g. flanged joints).
NOTE 3   For valves or valve bodies intended for drains and sewers, additional information is given in Clause 9.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 3 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17778:2015(Main)
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)
SIST EN ISO 17778:2015

ISO 17778:2015 specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping systems when tested using air at 25 mbar.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12119:1997(Main)
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling
SIST EN 12119:1999

This standard specifies a test method for the resistance of valves to thermal cycling. This standard is applicable to polyethylen (PE) valves and valves with PE spigot-ends having a nominal outside diameter greater than 63 mm and intended for the transport of fluids.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1680:1997(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
SIST EN 1680:1999

This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1705:1996(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
SIST EN 1705:1997

This standard specifies a method for determining the leaktightness and the ease of operation of a valve following an impact applied to the operating mechanism (cap) or other exposed mechanism.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 1680(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
kSIST FprEN 1680:2024

This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism.
Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material other than PE.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5640:2024(Main)
Industrial valves - Mounting kits for part-turn valve actuator attachment (ISO 5640:2024)
oSIST prEN ISO 5640:2024

This document provides requirements for metallic mounting kits for part-turn valves and actuator attachments.
It includes all components transmitting torques from actuators to valves with a maximum flange torque up to 16 000 Nm (up to F30 flange type).
It applies to mounting kits for part-turn valves and actuators with integral attachment flanges and drive components as described in ISO 5211, when direct mounting of the actuator on valve is not practical.
Stacking of mounting kits/intermediate supports is not within the scope of this document.
This document specifies methods for design and environmental corrosion protection.
When a reference is made to this document, all the requirements apply, unless otherwise agreed between the purchaser and the manufacturer/supplier, prior to order.
In this document, the term "valve" covers valve or shaft extension top-flange, and the term “actuator” covers part-turn actuator or combination of multi-turn actuator and gearbox.
Control valves are excluded from this document.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17955:2024(Main)
Industrial valves - Functional safety of safety-related automated valves
SIST EN 17955:2024

This document defines the requirements for how mechanical compliant items in a final element can be evaluated according to the principles of EN 61508 to integrate them into a safety-related system. It provides a method to determine all relevant factors, associated with the product, and thereby meet the specific needs of users of the product.
The basic prerequisite for the application of this document is that the intended use is known. This document describes a system to minimize systematic faults to achieve the targeted Safety Integrity Level (SIL).
This document is applied to single compliant items (e.g. valve, actuator or mechanical portions of solenoid valves) or to assemblies of several of these compliant items and interconnecting compliant items and components (e.g. gears, adaptors, brackets, etc.). Electrical, electronic or programmable electronic components are assessed according to EN 61508.
This document does not apply to:
-   manually operated valves;
-   items in safety systems or risk-reducing devices that are not assessed and operated according to the principles of functional safety (e.g. automatic safety valves like pressure relief valves).
The methods described can also be used for other mechanical compliant items in a final element of the safety-related system if the applicability is confirmed by appropriate expert knowledge (e.g. dampers, brakes, clutches).

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8233:2024(Main)
Thermoplastics valves - Torque - Test method (ISO 8233:2024)
SIST EN ISO 8233:2024

This document specifies a test method for the determination of the opening, closing and running torque of thermoplastics valves.
This document is applicable to all types of manually operable thermoplastics valves, with or without actuator, intended to be used for the transport of fluids.
NOTE 1        Examples of valve types tested with this method are in ISO 4437-4, ISO 16135, ISO 16136, ISO 16138, ISO 16139, ISO 16486-4, ISO 21787, EN 1555-4[13] and EN 12201-4 [14].
This document does not specify the relationship between the torque and its possible increase after prolonged use of the valve under a specific working condition or wear/chemical aggression of the materials.
NOTE 2        Concerning the chemical aggression of the materials, a collection of data is reported in ISO/TR 10358 concerning the endurance test necessary to confirm the ability of hand-operated plastics valves to withstand prolonged use with repeated opening and closing operations. Further information is provided in ISO 8659.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day