CEN ISO/TS 19807-1:2022
(Main)Nanotechnologies - Magnetic nanomaterials - Part 1: Specification of characteristics and measurements for magnetic nanosuspensions (ISO/TS 19807-1:2019)
Nanotechnologies - Magnetic nanomaterials - Part 1: Specification of characteristics and measurements for magnetic nanosuspensions (ISO/TS 19807-1:2019)
This document specifies the characteristics of magnetic nanosuspensions to be measured and lists measurement methods for measuring these characteristics.
This is a generic document and does not deal with any particular application.
Nanotechnologien - Magnetische Nanopartikel - Teil 1: Festlegung der Eigenschaften und Messung magnetischer Nanosuspensionen (ISO/TS 19807-1:2019)
Dieses Dokument legt die zu messenden Eigenschaften von magnetischen Nanosuspensionen fest und führt Verfahren zur Messung dieser Eigenschaften auf.
Dies ist ein allgemeines Dokument, das sich nicht auf bestimmte Anwendungen bezieht.
Nanotechnologies - Nanomatériaux magnétiques - Partie 1: Spécification des caractéristiques et des mesures pour les nanosuspensions magnétiques (ISO/TS 19807-1:2019)
Nanotehnologija - Magnetni nanomateriali - 1. del: Specifikacija lastnosti in meritev za magnetne nanosuspenzije (ISO/TS 19807-1:2019)
Ta dokument določa lastnosti magnetnih nanosuspenzij, predvidenih za merjenje, in navaja metode za merjenje teh lastnosti.
Ta dokument je splošen in ne obravnava posebnih vrst uporabe.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2022
Nanotehnologija - Magnetni nanomateriali - 1. del: Specifikacija lastnosti in
meritev za magnetne nanosuspenzije (ISO/TS 19807-1:2019)
Nanotechnologies - Magnetic nanomaterials - Part 1: Specification of characteristics and
measurements for magnetic nanosuspensions (ISO/TS 19807-1:2019)
Nanotechnologien - Magnetische Nanopartikel - Teil 1: Festlegung der Eigenschaften
und Messung magnetischer Nanosuspensionen (ISO/TS 19807-1:2019)
Nanotechnologies - Nanomatériaux magnétiques - Partie 1: Spécification des
caractéristiques et des mesures pour les nanosuspensions magnétiques (ISO/TS 19807-
1:2019)
Ta slovenski standard je istoveten z: CEN ISO/TS 19807-1:2022
ICS:
07.120 Nanotehnologije Nanotechnologies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN ISO/TS 19807-1
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
March 2022
TECHNISCHE SPEZIFIKATION
ICS 07.120
English Version
Nanotechnologies - Magnetic nanomaterials - Part 1:
Specification of characteristics and measurements for
magnetic nanosuspensions (ISO/TS 19807-1:2019)
Nanotechnologies - Nanomatériaux magnétiques - Nanotechnologien - Magnetische Nanopartikel - Teil 1:
Partie 1: Spécification des caractéristiques et des Festlegung der Eigenschaften und Messung
mesures pour les nanosuspensions magnétiques magnetischer Nanosuspensionen (ISO/TS 19807-
(ISO/TS 19807-1:2019) 1:2019)
This Technical Specification (CEN/TS) was approved by CEN on 20 March 2022 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 19807-1:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO/TS 19807-1:2019 has been prepared by Technical Committee ISO/TC 229
"Nanotechnologies” of the International Organization for Standardization (ISO) and has been taken over
as CEN ISO/TS 19807-1:2022 by Technical Committee CEN/TC 352 “Nanotechnologies” the secretariat
of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO/TS 19807-1:2019 has been approved by CEN as CEN ISO/TS 19807-1:2022 without any
modification.
TECHNICAL ISO/TS
SPECIFICATION 19807-1
First edition
2019-06
Nanotechnologies — Magnetic
nanomaterials —
Part 1:
Specification of characteristics
and measurements for magnetic
nanosuspensions
Nanotechnologies — Nanomatériaux magnétiques —
Partie 1: Spécification des caractéristiques et des mesures pour les
nanosuspensions magnétiques
Reference number
ISO/TS 19807-1:2019(E)
©
ISO 2019
ISO/TS 19807-1:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO/TS 19807-1:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 9
5 Characteristics and measurement methods of magnetic nanosuspensions .10
6 Reporting .12
Annex A (informative) Components of liquid suspensions of magnetic nanoparticles .13
Bibliography .15
ISO/TS 19807-1:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 229, Nanotechnologies.
A list of all parts in the ISO/TS 19807 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
ISO/TS 19807-1:2019(E)
Introduction
Nanomaterials offer the opportunity for new technologies at the interfaces between chemistry,
physics and biology. The term nanomaterial is used to refer to a wide range of particles, thin films,
self-assembling and lithographically produced structures in which at least one dimension is less than
100 nm. Magentic nanosuspensions are fluid nanodispersion, where the solid phase is formed by
magnetic nanoparticles.Magnetic nanosuspensions and bulk materials react to applied magnetic fields
in different ways. These unique properties enable the development of innovative technologies and
products.
Magnetic nanosuspensions have important potential industrial and healthcare applications such as
vacuum seals, lubricants, coolants, dampers, magnetic soaps, environmental remediation, medical
imaging, drug delivery technologies, magnetic hyperthermia therapy, etc. To satisfy the demands of
rapidly accelerating application markets, there is a strong need to provide universal definitions and
measurement methods for the characteristics of these suspensions. There are three components of
a magnetic nanosuspension: (1) magnetic nanoparticles (2) dispersing medium and (3) dispersant
(Annex A).
TECHNICAL SPECIFICATION ISO/TS 19807-1:2019(E)
Nanotechnologies — Magnetic nanomaterials —
Part 1:
Specification of characteristics and measurements for
magnetic nanosuspensions
1 Scope
This document specifies the characteristics of magnetic nanosuspensions to be measured and lists
measurement methods for measuring these characteristics.
This is a generic document and does not deal with any particular application.
2 Normative references
There are no normative references for this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
AC susceptibility
complex ratio between the dynamic magnetization and the applied magnetic excitation field
i2πft−φ
()
Note 1 to entry: The dynamic magnetization is given as MM= e and the applied magnetic excitation
i2πft
field is given as HH= e . The AC susceptibility χ =MH/ is divided into an in-phase component (real part)
′′′
and an out-of-phase component (imaginary part): χχ=− iχ .
Note 2 to entry: In dependence on the type of magnetization that is used, the AC susceptibility of a material is
related to volume, mass or amount of the material.
M M
AC volume susceptibility 0VV0
χϕ=−cossi inϕ
V
H H
0 0
M M
AC mass susceptibility 0mm0
χϕ=−cossi inϕ
m
H H
0 0
M M
0nn0
AC molar susceptibility
χϕ=−cossi inϕ
n
H H
0 0
Note 3 to entry: AC susceptibility depends on the excitation field frequency and the temperature, which should
also be indicated.
ISO/TS 19807-1:2019(E)
Note 4 to entry: The amplitude of the excitation field must be small enough so there is a linear relation between
the amplitude of the dynamic magnetization and the amplitude of the applied AC field.
3.2
agglomerate
collection of weakly or medium strongly bound particles where the resulting external surface area is
similar to the sum of the surface areas of the individual components
Note 1 to entry: The forces holding an agglomerate together are weak forces, for example van der Waals forces or
simple physical entanglement.
Note 2 to entry: Agglomerates are also termed secondary particles and the original source particles are ter
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.