EN 12629-1:2000+A1:2010
(Main)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
This European Standard applies to machines for the manufacture of constructional products from concrete and/or calcium silicate examples of which are listed in annex A of this part. It gives concepts and general and common requirements for the design, operation and maintenance of such machines.
1.2 This European Standard deals with hazards listed in Clause 4 which can arise during the operation and maintenance, including the interfaces, of the machines for the manufacture of constructional products from concrete and calcium silicate, when carried out as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
Part 2 to 8 of this standard give additional specific requirements and therefore have to be applied together with this part.
1.3 The preparation of concrete and/or calcium-silicate mixture and the transport from the mixer to the manufacturing plant are not part of this European Standard (see EN 12151:2007). The equipment for the transport and handling of formed products, other than the integrated transport system, is not covered by this stand
1.4 At the time of drafting, machine specific noise test codes for EN 12629-2 to -8 are not available to fulfill the requirements of 5.7.2 and 7.4.2. When they are available, they will be incorporated in these standards.
1.5 This document is not applicable to machines for the manufacture of constructional products from concrete and/or calcium silicate, which are manufactured before the date of publication of this document by CEN.
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 1: Gemeinsame Anforderungen
1.1 Diese Europäische Norm gilt für Maschinen zur Herstellung von Bauprodukten aus Beton und/oder
Kalksandsteinmassen wie aufgeführt in Anhang A dieser Europäischen Norm. Sie bietet Konzepte und
allgemeine Anforderungen für die Gestaltung, die Konstruktion, den Betrieb und die Instandhaltung solcher
Maschinen an.
1.2 !Diese Europäische Norm behandelt die in Abschnitt 4 aufgeführten Gefährdungen, die während des
Betriebs und der Wartung von Maschinen zur Herstellung von Bauprodukten aus Beton und/oder
Kalksandsteinmassen einschließlich der Schnittstellen auftreten können, wenn sie bestimmungsgemäß und
unter den Bedingungen des Missbrauchs, die vernünftigerweise vom Hersteller vorhersehbar sind, verwendet
werden.
Die Teile 2 bis 8 dieser Norm enthalten zusätzliche spezielle Anforderungen, deswegen müssen sie zusammen
mit diesem Teil gelten."
1.3 Die Zubereitung von Beton- und/oder Kalksandsteinmassen und der Transport vom Mischer zur
Produktionsstätte sind nicht Teil dieser Norm (siehe !EN 12151:2007"). Anders als die integrierten
Transportsysteme sind die Transporteinrichtungen und die Handhabung der fertigen Produkte ebenfalls nicht
Bestandteil dieser Norm.
!gestrichener Text"
!1.4" Zurzeit sind keine maschinenspezifischen Geräuschmessregeln für !EN 12629-2 bis
EN 12629-8" verfügbar, um die Anforderungen von 5.7.2 und 7.4.2 zu erfüllen. Sobald sie verfügbar sind,
werden sie in diese Normen aufgenommen.
!1.5 Dieses Dokument gilt nicht für Maschinen für die Herstellung von Bauprodukten aus Beton und
Kalksandsteinmassen, die vor dem Datum der Veröffentlichung dieses Dokuments durch CEN hergestellt
wurden."
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 1: Exigences communes
La présente Norme européenne s'applique aux machines pour la fabrication de produits de construction en
béton et silico-calcaire dont la liste se trouve en annexe A de cette partie. Elle donne des concepts et les exigences
générales et communes pour la conception, l'utilisation et la maintenance de telles machines.
1.2 !La présente Norme européenne traite les phénomènes dangereux significatifs énumérés à l'Article 4,
pouvant survenir pendant le fonctionnement et la maintenance, y compris aux interfaces, qui sont spécifiques aux
machines pour la fabrication de produits de construction en béton et silico-calcaire, lorsqu'elles sont utilisées comme
prévu ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir.
Les parties 2 à 8 de la présente norme donnent des prescriptions spécifiques supplémentaires et doivent donc être
appliquées conjointement à cette partie."
1.3 La préparation du béton et/ou du silico-calcaire, et le transport du malaxeur à l'installation de fabrication, ne
font pas partie de la présente Norme européenne (voir !EN 12151:2007"). Les équipements pour le transport et
la manutention des produits finis, autres que ceux intégrés aux systèmes de transport, ne sont pas pris en compte
dans cette norme.
1.4 Au stade actuel, des codes d'essai acoustique pour les !EN 12629-2 à 8" ne sont pas disponibles pour
parvenir aux prescriptions des paragraphes 5.7.2 et 7.4.2. Lorsque ceux-ci seront disponibles, ils seront incorporés
à ces normes.
1.5 !Le présent document ne s’applique pas aux machines pour la fabrication de produits de construction en
béton et/ou silico-calcaire, qui sont fabriquées avant la date de publication du présent document par le CEN."
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 1. del: Splošne zahteve
Ta evropski standard velja za stroje za izdelavo gradbenih proizvodov iz betona in/ali apnenega peščenca, primeri teh strojev pa so navedeni v Dodatku A tega dela. Podaja koncepte ter splošne in skupne zahteve za načrtovanje, obratovanje in vzdrževanje takšnih strojev. Ta evropski standard obravnava nevarnosti, navedene v Klavzuli 4, do katerih lahko pride med obratovanjem in vzdrževanjem strojev za izdelavo gradbenih proizvodov iz betona in apnenega peščenca, vključno z vmesniki, kadar se izvajata v skladu z namembnostjo in pod pogoji napačne uporabe, ki jih proizvajalec lahko razumno predvidi. Deli 2 do 8 tega standarda podajajo dodatne posebne zahteve in se morajo zato uporabljati skupaj s tem delom. Priprava zmesi betona in/ali apnenega peščenca ter prevoz od mešalnika do proizvodnega obrata nista del tega evropskega standarda (glej EN 12151:2007). Ta standard ne zajema opreme za prevoz in delo z oblikovanimi proizvodi, ki ni integriran prevozni sistem. V času priprave osnutka preskusne kode za hrup, specifičen za stroje, za EN 12629-2 do -8 še niso bile na voljo za izpolnjevanje zahtev iz točk 5.7.2 in 7.4.2. Ko bodo na voljo, bodo vključene v te standarde. Ta dokument ne velja za stroje za izdelavo gradbenih proizvodov iz betona in/ali apnenega peščenca, izdelane pred datumom, ko je CEN objavil ta dokument.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 1: Gemeinsame AnforderungenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 1: Exigences communesMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-1:2000+A1:2010SIST EN 12629-1:2000+A1:2010en,fr01-december-2010SIST EN 12629-1:2000+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-1:2000+A1
September 2010 ICS 91.220 Supersedes EN 12629-1:2000English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 1: Exigences communes
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 1: Gemeinsame Anforderungen This European Standard was approved by CEN on 12 May 2000 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-1:2000+A1:2010: ESIST EN 12629-1:2000+A1:2010
Contents Foreword . 4Introduction . 51Scope . 52Normative references . 53!!!!Terms and definitions"""" . 74List of significant hazards . 94.1Mechanical hazards . 94.2Electrical hazards . 94.3Hazards generated by noise . 94.4Hazards generated by materials and products . 94.5Hazards generated by neglecting ergonomic principles . 94.6Hazards caused by failure of energy supply . 95!!!!Safety requirements and/or protective measures"""" . 95.1Mobile parts of power transmission . 105.2Mobile parts taking part in the working process . 105.3Tool-setting changing of tools and machine maintenance operations . 125.4Safety functions treatment by control networks . 135.5Warning equipment . 135.6Electrical equipment . 135.7Noise . 135.8Materials and products . 145.9Ergonomic design. 145.10Hydraulic and pneumatic equipment . 145.11Integrated transport systems that are an integral part of the machine . 145.12!!!!Additional requirements for mobile manufacturing machines"""" . 146Verification of safety measures and/or provisions . 167Information for use . 177.1Safety systems . 177.2Interface . 187.3Spare parts . 187.4Noise . 187.5Access . 187.6Storage . 187.7Oils . 188Marking . 19SIST EN 12629-1:2000+A1:2010
Annex A (informative)
Examples of machines for the manufacture of constructional products from concrete and calcium silicate . 20Annex B (informative)
Guarding examples . 22Annex ZA (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 27!!!!Bibliography"""" . 28SIST EN 12629-1:2000+A1:2010
Foreword This document (EN 12629-1:2000+A1:2010) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by
March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-1:2000. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. !The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety" consists of the following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete roof tile making machines Part 5.1: Pipe making machines manufacturing in the vertical axis Part 5.2: Pipe making machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for long line manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)"
!deleted text" According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12629-1:2000+A1:2010
Introduction This European Standard is a Type C-standard as stated in !EN ISO 12100". The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. Reference to pertinent standards mentioned above is made where requirements of such standards are relevant. 1 Scope 1.1 This European Standard applies to machines for the manufacture of constructional products from concrete and/or calcium silicate examples of which are listed in annex A of this part. It gives concepts and general and common requirements for the design, operation and maintenance of such machines. 1.2 !!!!This European Standard deals with hazards listed in Clause 4 which can arise during the operation and maintenance, including the interfaces, of the machines for the manufacture of constructional products from concrete and calcium silicate, when carried out as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. Part 2 to 8 of this standard give additional specific requirements and therefore have to be applied together with this part." 1.3 The preparation of concrete and/or calcium-silicate mixture and the transport from the mixer to the manufacturing plant are not part of this European Standard (see !EN 12151:2007"). The equipment for the transport and handling of formed products, other than the integrated transport system, is not covered by this standard. !deleted text" !1.4" At the time of drafting, machine specific noise test codes for !EN 12629-2 to -8" are not available to fulfill the requirements of 5.7.2 and 7.4.2. When they are available, they will be incorporated in these standards. !1.5 This document is not applicable to machines for the manufacture of constructional products from concrete and/or calcium silicate, which are manufactured before the date of publication of this document by CEN." 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349:1993+A1:2008, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body EN 457:1992, Safety of machinery — Auditory danger signals — General requirements, design and testing EN 547-1:1996+A1:2008, Safety of machinery — Human body measurements – Part 1: Principles for determining the dimensions required for openings for whole body access into machinery EN 547-2+A1:2008, Safety of machinery — Human body measurements — Part 2: Principles for determining the dimensions required for access openings EN 547-3:1996+A1:2008, Safety of machinery — Human body measurements – Part 3: Anthropometric data SIST EN 12629-1:2000+A1:2010
EN 574, Safety of machinery — Two hand control devices – Functional aspects — Principles for design EN 614-1:2006+A1:2009, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general principles EN 626-1:1994+A1:2008, Safety
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.