prEN ISO 24466

Dentistry - Designations for the parts and dimensions of an implant body or a monopart implant (ISO/DIS 24466:2022)

This document defines terms for the parts of an implant body that are used in oral implantology as well
as the designation and determination of the dimensions and their data on the packaging of an oral
implant.
Four general terms for diameter (endosteal diameter, platform diameter) and length (endosteal length,
overall length) are defined and explained in examples.

Zahnheilkunde – Bezeichnungen für die Teile und Maße eines Implantatkörpers (ISO/DIS 24466:2022)

Médecine bucco-dentaire - Désignations pour les parts et les mesures des corps d'implant (ISO/DIS 24466:2022)

Zobozdravstvo - Označevanje delov in dimenzij telesa implantata ali enodelnega implantata (ISO/DIS 24466:2022)

General Information

• Status: Not Published
• Publication Date: 10-Sep-2023
• ICS: 11.060.15 - Dental implants
• Technical Committee: CEN/TC 55 - Dentistry
• Drafting Committee: CEN/TC 55 - Dentistry
• Ref Project: oSIST prEN ISO 24466:2022 - Dentistry - Designations for the parts and dimensions of an implant body or a monopart implant (ISO/DIS 24466:2022)

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2022
Zobozdravstvo - Označevanje delov in dimenzij telesa implantata ali enodelnega
implantata (ISO/DIS 24466:2022)
Dentistry - Designations for the parts and dimensions of an implant body or a monopart
implant (ISO/DIS 24466:2022)
Zahnheilkunde – Bezeichnungen für die Teile und Maße eines Implantatkörpers
(ISO/DIS 24466:2022)
Médecine bucco-dentaire - Désignations pour les parts et les mesures des corps
d'implant (ISO/DIS 24466:2022)
Ta slovenski standard je istoveten z: prEN ISO 24466
ICS:
11.060.15 Zobni implantati Dental implants
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 24466
ISO/TC 106/SC 8 Secretariat: ANSI
Voting begins on: Voting terminates on:
2022-02-10 2022-05-05
Dentistry — Designations for the parts and dimensions of
an implant body or a monopart implant
Médecine bucco-dentaire — Désignations pour les parts et les mesures des corps d'implant
ICS: 11.060.15
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24466:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

ISO/DIS 24466:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO/DIS 24466:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Multipart implant . . 2
4.1 Multipart implant with internal connection . 2
4.2 Multipart implant with external connection . 4
5 Monopart implant .5
5.1 Monopart implant with a ball head . 5
5.2 Monopart implant with a conical head . 6
6 Dimensions .7
6.1 Requirements . 7
6.2 Measurement of dimensional characteristics . 8
6.2.1 Bone diameter d . 8
6.2.2 Platform diameter D . 8
6.2.3 Implanted length l . 8
6.2.4 Total length L . 8
6.2.5 Conical implants . 8
7 Minimum data on outermost packaging . 8
7.1 General . 8
7.2 Multipart implant . 8
7.2.1 Bone level implant . 8
7.2.2 Tissue level implant . 9
7.2.3 External hex implant . 9
7.3 Monopart implant . 9
iii
ISO/DIS 24466:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 8, Dental
implants.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/DIS 24466:2022(E)
Introduction
The terms and designations used by the manufacturers of dental implants for the individual system
parts are not uniform.
As a first step all manufacturers of dent
...