EN 3745-503:2005
(Main)Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 503: Scrape abrasion
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 503: Scrape abrasion
This standard specifies a method for testing the resistance of an optical to scrape abrasion.
Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 503: Abriebbeständigkeit
Diese Norm legt ein Verfahren zur Prüfung der Abriebfestigkeit von Lichtwellenleiterkabeln fest.
Série aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 503 : Abrasion par raclage
Aeronavtika – Optična vlakna in kabli za uporabo v zračnih plovilih – Preskusne metode – 503. del: Obstojnost pri odrgnjenju
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 503: Scrape abrasionSérie aérospatiale - Fibres et câbles optiques a usage aéronautique - Méthodes d'essais - Partie 503 : Abrasion par raclageLuft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 503: AbriebbeständigkeitTa slovenski standard je istoveten z:EN 3745-503:2005SIST EN 3745-503:2006en49.060ICS:SLOVENSKI
STANDARDSIST EN 3745-503:200601-julij-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3745-503November 2005ICS 49.060 English VersionAerospace series - Fibres and cables, optical, aircraft use - Testmethods - Part 503: Scrape abrasionSérie aérospatiale - Fibres et câbles optiques à usageaéronautique - Méthodes d'essais - Partie 503 : Abrasionpar raclageLuft- und Raumfahrt - Faseroptische Leitungen fürLuftfahrzeuge - Prüfverfahren - Teil 503:AbriebbeständigkeitThis European Standard was approved by CEN on 19 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3745-503:2005: E
EN 3745-503:2005 (E) 2 Contents Foreword.3 1 Scope.4 2 Normative references.4 3 Preparation of specimens.4 4 Apparatus.4 5 Method.6
EN 3745-503:2005 (E) 3 Foreword This European Standard (EN 3745-503:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.