EN 3146:2001
(Main)Aerospace series - Round bars, hot rolled in steel - Close tolerances - Diameter 6 mm < = D < = 250 mm - Dimensions
Aerospace series - Round bars, hot rolled in steel - Close tolerances - Diameter 6 mm < = D < = 250 mm - Dimensions
This standard specifies the dimensions and tolerances of:
Round bars, hot rolled
in steel
Close tolerances
Diameter 6 mm £ D £ 250 mm
for aerospace applications.
Luft- und Raumfahrt - Rundstangen, warmgewalzt, aus Stahl - Enge Toleranzen - Durchmesser 6 mm # D # 250 mm - Maße
Diese Norm legt die Maße und Toleranzen von:
Rundstangen, warmgewalzt
aus Stahl
Enge Toleranzen
Durchmesser 6 mm = D = 250 mm
für Anwendungen in der Luft- und Raumfahrt fest.
Série aérospatiale - Barres rondes, laminées à chaud en acier - Tolérances serrées - Diamètres 6 mm < = D < = 250 mm - Dimensions
Aerospace series - Round bars, hot rolled in steel - Close tolerances - Diameter 6 mm < = D < = 250 mm - Dimensions
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2002
Aerospace series - Round bars, hot rolled in steel - Close tolerances - Diameter 6
mm < = D < = 250 mm - Dimensions
Aerospace series - Round bars, hot rolled in steel - Close tolerances - Diameter 6 mm <
= D < = 250 mm - Dimensions
Luft- und Raumfahrt - Rundstangen, warmgewalzt, aus Stahl - Enge Toleranzen -
Durchmesser 6 mm # D # 250 mm - Maße
Série aérospatiale - Barres rondes, laminées a chaud en acier - Tolérances serrées -
Diametres 6 mm < = D < = 250 mm - Dimensions
Ta slovenski standard je istoveten z: EN 3146:2001
ICS:
49.025.10 Jekla Steels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 3146
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2001
ICS 49.025.10
English version
Aerospace series - Round bars, hot rolled in steel - Close
tolerances - Diameter 6 mm D 250 mm - Dimensions
Série aérospatiale - Barres rondes, laminées à chaud en Luft- und Raumfahrt - Rundstangen, warmgewalzt aus
acier - Tolérances serrées - Diamètres 6 mm D 250 Stahl - Eingeengte Toleranzen - Durchmesser 6 mm D
mm - Dimensions 250 mm - Maße
This European Standard was approved by CEN on 2 May 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3146:2001 E
worldwide for CEN national Members.
Foreword
This European Standard has been prepared by the European Association of Aerospace Manufacturers
(AECMA).
After inquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2002, and conflicting national standards shall be withdrawn at
the latest by March 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, Fr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.