prEN 3719
(Main)Aerospace series - Aluminium or aluminium alloy conductors for electrical cables - Product standard
Aerospace series - Aluminium or aluminium alloy conductors for electrical cables - Product standard
This document specifies the dimensions, linear resistance, mechanical characteristics, construction and mass of conductors in aluminium or aluminium alloy for electrical cables for aerospace applications.
It applies to stranded conductors with nominal cross-sections of 5 mm2 to 115 mm2 inclusive.
Luft- und Raumfahrt - Leiter aus Aluminium oder Aluminiumlegierung für elektrische Leitungen - Produktnorm
Série aérospatiale - Conducteurs en aluminium ou en alliage d'aluminium pour câbles électriques - Norme de produit
Le présent document spécifie les dimensions, la résistance linéaire, les caractéristiques mécaniques, la construction et la masse des conducteurs en aluminium ou en alliage d'aluminium pour les câbles électriques utilisés dans les applications aérospatiales.
Il s'applique aux conducteurs toronnés ayant une section nominale de 5 mm2 à 115 mm2 incluse.
Aeronavtika - Vodniki za električne kable iz aluminija in aluminijevih zlitin - Standard za proizvod
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2024
Aeronavtika - Vodniki za električne kable iz aluminija in aluminijevih zlitin -
Standard za proizvod
Aerospace series - Aluminium or aluminium alloy conductors for electrical cables -
Product standard
Luft- und Raumfahrt - Leiter aus Aluminium oder Aluminiumlegierung für elektrische
Leitungen - Produktnorm
Série aérospatiale - Conducteurs en aluminium ou en alliage d'aluminium pour câbles
électriques - Norme de produit
Ta slovenski standard je istoveten z: prEN 3719
ICS:
49.025.20 Aluminij Aluminium
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2024
ICS 49.060 Will supersede EN 3719:2018
English Version
Aerospace series - Aluminium or aluminium alloy
conductors for electrical cables - Product standard
Série aérospatiale - Conducteurs en aluminium ou en Luft- und Raumfahrt - Leiter aus Aluminium oder
alliage d'aluminium pour câbles électriques - Norme de Aluminiumlegierung für elektrische Leitungen -
produit Produktnorm
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 3719:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms, definitions and symbols . 4
4 Conductor materials and construction . 4
4.1 Materials . 4
4.2 Material for individual strands and code . 4
4.3 Aluminium or aluminium alloy. 5
4.4 Construction of conductors . 5
4.4.1 Lay length . 5
4.4.2 Joints . 5
4.4.3 Compaction . 5
5 Required characteristics . 6
6 Test methods . 8
7 Quality assurance . 8
8 Designation . 8
9 Marking, packaging and delivery lengths . 9
European foreword
This document (prEN 3719:2024) has been prepared by ASD-STAN.
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 3719:2018.
2 2
— Correction of typo in the scope: 115 mm inclusive rather than 107 mm inclusive;
— Update of Clause 2 “Normative references”;
— Redrawing of Table 1 “Chemical composition of aluminium alloy”;
— Addition of conductor construction for cross-section code 115 in Table 3 “Conductor constructions
with strand Ø 0,34 mm”.
1 Scope
This document specifies the dimensions, linear resistance, mechanical characteristics, construction and
mass of conductors in aluminium or aluminium alloy for electrical cables for aerospace applications.
2 2
It applies to stranded conductors with nominal cross-sections of 5 mm to 115 mm inclusive.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products —
Part 3: Chemical composition and form of products
EN 1715-2, Aluminium and aluminium alloys — Drawing stock — Part 2: Specific requirements f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.