iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12119:1997

(Main)

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling

This standard specifies a test method for the resistance of valves to thermal cycling. This standard is applicable to polyethylen (PE) valves and valves with PE spigot-ends having a nominal outside diameter greater than 63 mm and intended for the transport of fluids.

Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für die Beständigkeit bei Temperaturwechsel

Diese Norm legt ein Verfahren zur Prüfung der Beständigkeit gegen Temperaturwechsel von Armaturen fest. Sie gilt für Armaturen aus Polyethylen (PE) sowie für Armaturen mit PE-Einstecken mit einem Nenn-Außendurchmesser gröser als 63 mm, die in Rohrleitungen zum Transport von Fluiden Verwendung finden.

Systèmes de canalisations en plastique - Robinets en polyéthylène (PE) - Méthode d'essai de résistance aux cycles thermiques

La présente norme spécifie une méthode d'essai relative à la résistance des robinets aux cycles thermiques. Cette norme s'applique aux robinets en polyéthylène (PE) et à ceux munis de manchettes en PE, présentant un diamètre extérieur nominal supérieur à 63 mm, destinés au transport de fluides.

Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za preskus odpornosti proti cikličnim spremembam temperature

General Information

Status
Published
Publication Date
20-May-1997
ICS
23.060.01 - Valves in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 32 - Valves
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
30-Aug-2020
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 12119:1999 - Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling

Buy Standard

EN 12119:1999EN 12119:1999
PreviousNext
Standard
EN 12119:1999
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für die Beständigkeit bei TemperaturwechselSystemes de canalisations en plastique - Robinets en polyéthylene (PE) - Méthode d'essai de résistance aux cycles thermiquesPlastics piping systems - Polyethylene (PE) v
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
SIST EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial applications.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.4. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [2].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 12201-2 and EN 12201-3 respectively.
Valves made from materials other than PE, conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, conforming to EN 12201-3, or material transition joints (e.g. flanged joints).
NOTE 3   For valves or valve bodies intended for drains and sewers, additional information is given in Clause 9.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 3 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17778:2015(Main)
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)
SIST EN ISO 17778:2015

ISO 17778:2015 specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping systems when tested using air at 25 mbar.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1680:1997(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
SIST EN 1680:1999

This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1705:1996(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
SIST EN 1705:1997

This standard specifies a method for determining the leaktightness and the ease of operation of a valve following an impact applied to the operating mechanism (cap) or other exposed mechanism.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1705(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
oSIST prEN 1705:2024

This document specifies a test method for determining the leaktightness and the ease of operation of a valve made of thermoplastic material following an impact applied to the operating device.
Additionally, a different procedure of the test on diaphragm valve can be specified by the valve manufacturer.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 1680(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
oSIST prEN 1680:2024

This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism.
Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material other than PE.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17955:2024(Main)
Industrial valves - Functional safety of safety-related automated valves
SIST EN 17955:2024

This document defines the requirements for how mechanical compliant items in a final element can be evaluated according to the principles of EN 61508 to integrate them into a safety-related system. It provides a method to determine all relevant factors, associated with the product, and thereby meet the specific needs of users of the product.
The basic prerequisite for the application of this document is that the intended use is known. This document describes a system to minimize systematic faults to achieve the targeted Safety Integrity Level (SIL).
This document is applied to single compliant items (e.g. valve, actuator or mechanical portions of solenoid valves) or to assemblies of several of these compliant items and interconnecting compliant items and components (e.g. gears, adaptors, brackets, etc.). Electrical, electronic or programmable electronic components are assessed according to EN 61508.
This document does not apply to:
-   manually operated valves;
-   items in safety systems or risk-reducing devices that are not assessed and operated according to the principles of functional safety (e.g. automatic safety valves like pressure relief valves).
The methods described can also be used for other mechanical compliant items in a final element of the safety-related system if the applicability is confirmed by appropriate expert knowledge (e.g. dampers, brakes, clutches).

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8233:2024(Main)
Thermoplastics valves - Torque - Test method (ISO 8233:2024)
SIST EN ISO 8233:2024

This document specifies a test method for the determination of the opening, closing and running torque of thermoplastics valves.
This document is applicable to all types of manually operable thermoplastics valves, with or without actuator, intended to be used for the transport of fluids.
NOTE 1        Examples of valve types tested with this method are in ISO 4437-4, ISO 16135, ISO 16136, ISO 16138, ISO 16139, ISO 16486-4, ISO 21787, EN 1555-4[13] and EN 12201-4 [14].
This document does not specify the relationship between the torque and its possible increase after prolonged use of the valve under a specific working condition or wear/chemical aggression of the materials.
NOTE 2        Concerning the chemical aggression of the materials, a collection of data is reported in ISO/TR 10358 concerning the endurance test necessary to confirm the ability of hand-operated plastics valves to withstand prolonged use with repeated opening and closing operations. Further information is provided in ISO 8659.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
SIST EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial applications.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.4. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [2].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to EN 12201-2 and EN 12201-3 respectively.
Valves made from materials other than PE, conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, conforming to EN 12201-3, or material transition joints (e.g. flanged joints).
NOTE 3   For valves or valve bodies intended for drains and sewers, additional information is given in Clause 9.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 3 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day