EN 3745-510:2012
(Main)Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 510: Bending test
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 510: Bending test
This European Standard specifies a method of determining the attenuation variation of an optical cable during mechanical bending under load at the maximum and minimum operating temperatures.
Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 510: Biegetest
Diese Europäische Norm legt ein Verfahren zur Bestimmung der Dämpfungsänderung in einer optischen Leitung bei mechanischer Biegung unter Krafteinwirkung sowie bei Höchst- und Mindestbetriebstemperatur fest.
Série aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 510: Essai de courbure
La présente Norme Européenne spécifie une méthode pour déterminer la variation d'atténuation d'un câble optique durant une courbure mécanique sous charge aux températures d’utilisation minimales et maximales.
Aeronavtika - Optična vlakna in kabli za uporabo v zračnih plovilih - Preskusne metode - 510. del: Upogibni preskus
Ta evropski standard določa metodo za ugotavljanje sprememb v slabljenju optičnega kabla med mehanskim upogibanjem pod obtežbo pri najvišji in najnižji obratovalni temperaturi.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 510: BiegetestSérie aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 510 : Essai de courbureAerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 510: Bending test49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 3745-510:2012SIST EN 3745-510:2012en,de01-oktober-2012SIST EN 3745-510:2012SLOVENSKI
STANDARDSIST EN 3745-510:20041DGRPHãþD
SIST EN 3745-510:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3745-510
August 2012 ICS 49.090 Supersedes EN 3745-510:2002English Version
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 510: Bending test
Série aérospatiale - Fibres et câbles optiques à usage aéronautique - Méthodes d'essais - Partie 510: Essai de courbure
Luft- und Raumfahrt - Faseroptische Leitungen für Luftfahrzeuge - Prüfverfahren - Teil 510: Biegetest This European Standard was approved by CEN on 23 March 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3745-510:2012: ESIST EN 3745-510:2012
EN 3745-510:2012 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Preparation of specimens .44Apparatus .55Methods .7 SIST EN 3745-510:2012
EN 3745-510:2012 (E) 3 Foreword This document (EN 3745-510:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn at the latest by February 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 3745-510:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.