Modular mechanical locked floor coverings (MMF) - Determination of geometrical characteristics

This document specifies test methods for the determination of geometrical characteristics of modular mechanical locked floor covering panels in respect of thickness, length, width, squareness, straightness, width flatness, length flatness, openings between assembled elements and height differences between assembled elements.
The geometrical characteristics of modular mechanical locked panels are important considerations because installed flooring will have an objectionable appearance if these performance criteria are not followed. This can cause the installed panels to line up unevenly, producing unsightly seams, uneven surfaces and corners that do not match.

Modulare mechanisch verriegelnde Fußbodenbeläge (MMF) - Bestimmung der geometrischen Eigenschaften

Dieses Dokument legt Prüfverfahren zur Bestimmung geometrischer Eigenschaften von modularen mechanisch verriegelnden Fußbodenpaneelen in Bezug auf die Dicke, Länge, Breite, Rechtwinkligkeit, Geradheit, Ebenheit in der Breite, Ebenheit in der Länge, Fugenöffnungen zwischen montierten Elementen und Höhenunterschiede zwischen montierten Elementen fest.
Die geometrischen Eigenschaften von modularen mechanisch verriegelnden Fußbodenpaneelen sind wichtige Faktoren, da verlegter Bodenbelag ein störendes Erscheinungsbild haben kann, wenn diese Leistungskriterien nicht erfüllt werden. Das kann dazu führen, dass die verlegten Paneele nicht gleichmäßig ausgerichtet sind, was zu unansehnlichen Fugen, unebenen Oberflächen und nicht aufeinander passenden Ecken führt.

Revêtements de sol modulaires à verrouillage mécanique (MMF) - Détermination des caractéristiques géométriques

Le présent document spécifie les méthodes d'essai pour déterminer les caractéristiques géométriques des panneaux de revêtements de sol modulaires à verrouillage mécanique par rapport à l'épaisseur, la longueur, la largeur, l'équerrage, la rectitude, la planéité en largeur, la planéité en longueur et les ouvertures ainsi que les différences de hauteur entre les éléments assemblés.
Les caractéristiques géométriques des panneaux modulaires à verrouillage mécanique sont des facteurs importants à prendre en compte car il en va de la bonne apparence du sol installé si ces critères de performance ne sont pas respectés. Les panneaux installés peuvent, le cas échéant, être alignés de façon désordonnée, ce qui entraîne des raccords disgracieux, des surfaces irrégulières et des angles non concordants.

Modularne mehansko spojene talne obloge (MMF) - Ugotavljanje geometrijskih značilnosti

General Information

Status
Published
Publication Date
10-Aug-2021
Withdrawal Date
27-Feb-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Aug-2021
Due Date
10-Apr-2022
Completion Date
11-Aug-2021

Buy Standard

Standard
EN 17539:2021
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2021
Modularne mehansko spojene talne obloge (MMF) - Ugotavljanje geometrijskih
značilnosti
Modular mechanical locked floor coverings (MMF) - Determination of geometrical
characteristics
Modulare mechanisch verriegelnde Fußbodenbeläge (MMF) - Bestimmung der
geometrischen Eigenschaften
Revêtements de sol modulaires à verrouillage mécanique (MMF) - Détermination des
caractéristiques géométriques
Ta slovenski standard je istoveten z: EN 17539:2021
ICS:
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17539
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2021
EUROPÄISCHE NORM
ICS 97.150
English Version
Modular mechanical locked floor coverings (MMF) -
Determination of geometrical characteristics
Revêtements de sol modulaires à verrouillage Modulare mechanisch verriegelnde Fußbodenbeläge
mécanique (MMF) - Détermination des caractéristiques (MMF) - Bestimmung der geometrischen Eigenschaften
géométriques
This European Standard was approved by CEN on 4 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17539:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principles . 7
4.1 Thickness . 7
4.2 Length and width . 7
4.3 Squareness . 7
4.4 Straightness . 7
4.5 Flatness . 7
4.6 Openings and height differences . 7
5 Apparatus . 7
5.1 Apparatus for thickness measurement. 7
5.2 Apparatus for length and width measurement . 7
5.3 Apparatus for squareness measurement . 8
5.4 Apparatus for straightness measurement . 8
5.5 Apparatus for determination of flatness . 8
5.6 Apparatus for openings and height differences . 9
6 Sampling and selection of specimens . 9
7 Atmosphere for conditioning and testing . 9
8 Procedure . 9
8.1 Determination of thickness . 9
8.2 Determination of length and width . 10
8.3 Determination of straightness and squareness . 10
8.3.1 Squareness . 10
8.3.2 Straightness . 11
8.4 Determination of flatness . 12
8.4.1 Determination of width flatness . 12
8.4.2 Determination of length flatness . 12
8.5 Determination of openings and height differences between panels . 13
8.5.1 General. 13
8.5.2 Determination of openings between the panels . 13
8.5.3 Determination of height differences . 13
9 Calculation and expression of results . 14
9.1 Thickness . 14
9.2 Length and Width . 14
9.3 Squareness . 14
9.4 Straightness . 14
9.5 Flatness . 14
9.5.1 Width flatness . 14
9.5.2 Length flatness . 14
9.6 Openings and height differences . 14
10 Precision statement . 14
11 Test report . 15
Bibliography . 16

European foreword
This document (EN 17539:2021) has been prepared by Technical Committee CEN/TC 134 “Resilient,
textile and laminate floor coverings”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2022, and conflicting national standards
shall be withdrawn at the latest by February 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
The technical committee CEN/TC 134 decided to develop a series of generic test methods able to
demonstrate the characteristics of modular mechanical locked floor covering panels. This series of test
methods will be used in the common part of individual product specification standards.
1 Scope
This document specifies test methods for the determination of geometrical characteristics of modular
mechanical locked floor covering panels in respect of thickness, length, width, squareness, straightness,
width flatness, length flatness, openings between assembled elements and height differences between
assembled elements.
The geometrical characteristics of modular mechanical locked panels are important considerations
because installed flooring will have an objectionable appearance if these performance criteria are not
followed. This can cause the installed panels to line up unevenly, producing unsightly seams, uneven
surfaces and corners that do not match.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
floor covering panel with mechanical locking system
rigid or semi-rigid floor covering, typically in a plank or tile format, consisting of a compact layer of a
substrate and a decorative surface layer for floating installation
3.2
decorative layer
layer providing visual and aesthetic properties, intended to be the visible side when the floor is
installed
Note 1 to entry: Decorative layers can consist of resilient layers including cork, layers with aminoplastic
thermosetting resins and wood veneer layers with a thickness < 2,5 mm and textile surfaces.
3.3
squareness
measurement of the amount each corner of the tile deviates from 90°
3.4
straightness
property of an edge to be straight, unbent
4 Principles
4.1 Thickness
The test piece is placed between two parallel plates, and the distance between them is measured.
4.2 Length and width
The surface dimensions of a modular mechanical locked floor covering panel are measured by a contact
method at defined positions in each direction. The measurement is taken at the edges of the surface
layer.
4.3 Squareness
To assess the squareness, each corner of a right-angled panel is fitted into the dihedral angle of a
precision square and the maximum gap between the arm of the square and the ends of the panel is
measured.
4.4 Straightness
To assess the straightness, the maximum opening between the panel and the straight edge is measured
on the concave side using a suitable gauge.
4.5 Flatness
To assess width flatness the deviation in height is measured by direct contact with a dial gauge
maintained at constant height. To
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.