EN 13384-1:2015

Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance

This European Standard specifies methods for the calculation of the thermal and fluid dynamic characteristics of chimneys serving one heating appliance.
The methods in this part of this European Standard are applicable to negative or positive pressure chimneys with wet or dry operating conditions. It is valid for chimneys with heating appliances for fuels subject to the knowledge of the flue gas characteristics which are needed for the calculation.
The methods in this part of this European Standard are applicable to chimneys with one inlet connected with one appliance. The methods in Part 2 of this European Standard are applicable to chimneys with multiple inlets and one inlet with multiple appliances. Part 3 describes methods for the development of diagrams and tables for chimneys serving one heating appliance.

Abgasanlagen - Wärme- und strömungstechnische Berechnungsverfahren - Teil 1: Abgasanlagen mit einer Feuerstätte

Diese Europäische Norm legt wärme- und strömungstechnische Berechnungsverfahren von Abgasanlagen mit einer Feuerstätte fest.
Diese Europäische Norm gilt sowohl für Unterdruck- als auch für Überdruckanlagen in feuchter und trockener Betriebsweise. Sie gilt für Abgasanlagen von Feuerstätten mit Brennstoffen, deren Abgaskennwerte, die für die Berechnung benötigt werden, bekannt sind.
Das Berechnungsverfahren dieser Europäischen Norm gilt für Abgasanlagen mit einem Anschluss für eine Feuerstätte. Das Berechnungsverfahren nach Teil 2 dieser Europäischen Norm gilt dagegen für Abgasanlagen mit mehreren Anschlüssen und für einen Anschluss mit mehreren Feuerstätten. Teil 3 beschreibt Verfahren zur Entwicklung von Diagrammen und Tabellen für Abgasanlagen mit einer Feuerstätte.

Conduits de fumée - Méthodes de calcul thermo-aéraulique - Partie 1: Conduits de fumée ne desservant qu'un seul appareil

La présente Norme européenne spécifie les méthodes de calcul des caractéristiques thermo-aérauliques des conduits de fumée ne desservant qu'un seul appareil.
Les méthodes données dans la présente partie de cette Norme européenne s'appliquent aux conduits de fumée fonctionnant sous pression négative ou positive, en ambiance humide ou sèche, et desservant des générateurs de chaleur utilisant des combustibles dont les caractéristiques des fumées sont connues pour les calculs.
Les méthodes données dans la présente partie de cette Norme européenne s'appliquent aux conduits de fumée desservant un seul  appareil. Les méthodes données dans la partie 2 de la présente Norme européenne concernent les conduits de fumée desservant plusieurs appareils (conduit collectif ou cascade). La partie 3 décrit des méthodes qui permettent d'élaborer des abaques et des tableaux pour les conduits de fumée desservant un seul générateur de chaleur.

Dimniki - Računske metode termodinamike in dinamike fluidov - 1. del: Dimniki za eno ogrevalno napravo

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2015
• Withdrawal Date: 02-Jul-2019
• ICS: 91.060.40 - Chimneys, shafts, ducts
• Technical Committee: CEN/TC 166 - Chimneys
• Drafting Committee: CEN/TC 166/WG 2 - Thermal and fluid dynamic calculation methods for chimneys
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 03-Jul-2019
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/105 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on chimneys, flues and specific products
• Ref Project: SIST EN 13384-1:2015 - Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance

Relations

• Replaces: EN 13384-1:2002+A2:2008 - Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one appliance
• Effective Date: 08-Apr-2015
• Merged Into: EN 13384-1:2015+A1:2019 - Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one combustion appliance
• Effective Date: 18-Jan-2023
• Amended By: EN 13384-1:2015/prA1 - Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance
• Effective Date: 14-Jun-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2015
1DGRPHãþD
SIST EN 13384-1:2003+A2:2008
'LPQLNL5DþXQVNHPHWRGHWHUPRGLQDPLNHLQGLQDPLNHIOXLGRYGHO'LPQLNL]D
HQRRJUHYDOQRQDSUDYR
Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving
one heating appliance
Abgasanlagen - Wärme- und strömungstechnische Berechnungsverfahren - Teil 1:
Abgasanlagen mit einer Feuerstätte
Conduits de fumée - Méthodes de calcul thermo-aéraulique - Partie 1: Conduits de
fumée ne desservant qu'un seul appareil
Ta slovenski standard je istoveten z: EN 13384-1:2015
ICS:
91.060.40 Dimniki, jaški, kanali Chimneys, shafts, ducts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13384-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2015
ICS 91.060.40 Supersedes EN 13384-1:2002+A2:2008
English Version
Chimneys - Thermal and fluid dynamic calculation methods -
Part 1: Chimneys serving one heating appliance
Conduits de fumée - Méthodes de calcul thermo-aéraulique Abgasanlagen - Wärme- und strömungstechnische
- Partie 1: Conduits de fumée ne desservant qu'un seul Berechnungsverfahren - Teil 1: Abgasanlagen mit einer
appareil Feuerstätte
This European Standard was approved by CEN on 24 January 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13384-1:2015 E
worldwide for CEN national Members.

Contents Page
Foreword .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 Symbols and abbreviations . 10
5 Calculation method for non-balanced flue chimneys . 14
5.1 General principles. 14
5.2 Pressure requirements . 15
5.2.1 Negative pressure chimneys . 15
5.2.2 Positive pressure chimneys . 16
5.3 Temperature requirement . 16
5.4 Calculation procedure . 17
5.5 Flue gas data characterising the heating appliance . 18
5.5.1 General . 18
5.5.2 Flue gas mass flow . 18
5.5.3 Flue gas temperature . 19
5.5.4 Minimum draught for the heating appliance (P ) for negative pressure chimney . 19
W
5.5.5 Maximum draught for the heating appliance (P ) for negative pressure chimney . 20
Wmax
5.5.6 Maximum differential pressure of the heating appliance (P ) for positive pressure
WO
chimney . 20
5.5.7 Minimum differential pressure of the heating appliance (P ) for positive pressure
WOmin
chimney . 20
5.6 Characteristic data for the calculation . 20
5.6.1 General . 20
5.6.2 Mean value for roughness (r) . 20
5.6.3 Thermal resistance (1/Λ) . 20
5.7 Basic values for the calculation . 21
5.7.1 Air temperatures . 21
5.7.2 External air pressure (p ) . 23
L
5.7.3 Gas constant . 23
5.7.4 Density of the external air (ρ ) . 24
L
5.7.5 Specific heat capacity of the flue gas (c ) . 24
p
5.7.6 Condensing temperature (T ) . 24
sp
5.7.7 Correction factor for temperature instability (S ) . 24
H
5.7.8 Flow safety coefficient (S ) . 24
E
5.8 Determination of the temperatures . 25
5.8.1 General . 25
5.8.2 Calculation of the coefficient of cooling (K) . 25
5.8.3 Coefficient of heat transmission (k ) . 26
b
5.9 Determination of the density of the flue gas and the velocity of the flue gas . 28
5.9.1 Density of the flue gas (ρ ) . 28
m
5.9.2 Velocity of the flue gas (w ) . 28
m
5.10 Determination of the pressures . 29
5.10.1 Pressure at the flue gas inlet into the chimney . 29
5.10.2 Theoretical draught available due to chimney effect (P ) . 30
H
5.10.3 Pressure resistance of the chimney (P ) . 30
R
5.10.4 Wind velocity pressure (P ) . 31
L
5.11 Minimum draught required at the flue gas inlet into the chimney and maximum allowed
and P ) and maximum and minimum differential pressure at the flue gas
draught (P
Ze Zemax
and P ) . 32
inlet into the chimney (P
ZOe ZOemin
5.11.1 General . 32
5.11.2 Minimum and maximum draught for the heating appliance (P and P ) and maximum
W Wmax
and P ) . 33
and minimum differential pressure of the heating appliance (P
WO WOmin
5.11.3 Effective pressure resistance of the connecting flue pipe (P ) . 33
FV
5.11.4 Pressure resistance of the air supply (P ) . 34
B
5.12 Calculation of the inner wall temperature at the chimney outlet (T ) . 35
iob
6 Secondary air for negative pressure chimneys . 37
6.1 General . 37
6.2 Calculation method . 37
6.3 Basic values for the calculation of secondary air . 37
6.3.1 General . 37
6.3.2 Mixing calculations . 37
6.4 Pressures . 38
6.4.1 Pressure resistance for the air supply with secondary air (P ) . 38
BNL
6.4.2 Draught required for the secondary air devices (P ) . 39
NL
6.4.3 Pressure resistance for that part of the connecting flue pipe before the secondary air
) . 40
device (P
FV1
6.4.4 Pressure requirement with secondary air . 41
6.5 Temperature requirement with secondary air . 41
7 Calculation method for balanced flue chimneys . 41
7.1 General principles . 41
7.2 Pressure requirements . 42
7.3 Temperature requirements . 43
7.4 Calculation procedure . 43
7.5 Flue gas data characterizing the heating appliance . 43
7.6 Characteristic data for the calculation . 44
7.7 Basic values for the calculation . 44
7.7.1 Air temperatures . 44
7.7.2 Other basic values . 45
7.8 Determination of the temperatures . 45
7.8.1 Non-concentric (separate) ducts . 45
7.8.2 Concentric ducts – calculation based on a correction factor for heat radiation . 45
7.8.3 Concentric ducts – calculation based on calculated heat radiation . 60
7.8.4 Mean temperatures for pressure calculation.
...