EN 13480-2:2017/A7:2020
(Amendment)Metallic industrial piping - Part 2: Materials
Metallic industrial piping - Part 2: Materials
This Part of this European Standard specifies the requirements for materials (including metallic clad materials) for industrial piping and supports covered by EN 13480-1 manufactured from of metallic materials. It is currently limited to steels with sufficient ductility. This Part of this European Standard is not applicable to materials in the creep range.
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2 : Matériaux
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A7
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2020
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A7
Metallic industrial piping - Part 2: Materials
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2 : Matériaux
Ta slovenski standard je istoveten z: EN 13480-2:2017/A7:2020
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13480-2:2017/A7
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Metallic industrial piping - Part 2: Materials
Tuyauteries industrielles métalliques - Partie 2 : Metallische industrielle Rohrleitungen - Teil 2:
Matériaux Werkstoffe
This amendment A7 modifies the European Standard EN 13480-2:2017; it was approved by CEN on 10 February 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-2:2017/A7:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to Clause 2, Normative references . 4
2 Modification to 4.2.1.1, General . 4
3 Modification to 4.2.1.2, Lamellar tearing . 4
4 Modification to Annex ZA, Relationship between this European Standard and the
Essential Requirements of EU Directive 2014/68/EU aimed to be cov
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.