Aerospace series - Heat shrinkable moulded shapes - Part 102: Elastomeric, semi-rigid, temperature range -75 to 150 °C - Product Standard

This document specifies the required characteristics for heat-shrinkable elastomeric semi-rigid, boots for use in aircraft electrical systems at operating temperatures between -75 °C and 150 °C.
The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers for options. A guide to adhesive compatibility is given in Annex A (informative).
These moulded shapes are normally supplied in the styles and dimensions given in EN 4840-002 Table 1 to Table 22. The colour is normally black.
Styles and dimensions other than those specifically listed in EN 4840-002 Table 1 to Table 22 may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 1 with the exception of dimensions.

Luft- und Raumfahrt - Wärmeschrumpfende Formteile - Teil 102: Elastomer, halbsteif, Temperaturbereich -75 °C bis 150 °C - Produktnorm

Dieses Dokument legt die Eigenschaften für wärmeschrumpfende, halbsteife Elastomer Tüllen zur Verwen¬dung in elektrischen Systemen von Luftfahrzeugen bei Betriebstemperaturen zwischen −75 °C und 150 °C fest.
Die Formteile dürfen mit Klebstoff beschichtet angeboten werden. Für Varianten siehe Hersteller/Lieferan¬ten. Eine Anleitung hinsichtlich der Kompatibilität des Klebstoffs ist in Anhang A (informativ) angegeben.
Diese Formteile werden üblicherweise in den in EN 4840 002, Tabelle 1 bis Tabelle 22, angegebenen Aus¬führungen und Maßen angeboten. Die Farbe ist üblicherweise schwarz.
Andere Ausführungen und Maße als die speziell in EN 4840 002, Tabelle 1 bis Tabelle 22, angegebenen dürfen nach Kundenwünschen angeboten werden. Diese Teile gelten als mit dieser Norm übereinstimmend, wenn sie, mit Ausnahme der Maße, die in Tabelle 1 angegebenen Anforderungen an die Merkmale erfüllen.

Série aérospatiale - Manchons thermorétractables - Partie 102 : Semi-rigides en élastomère, plage de températures de -75 °C à 150 °C - Norme de produit

Le présent document spécifie les caractéristiques requises pour les soufflets de manchons thermorétractables semi-rigides en élastomère destinés à une utilisation dans les systèmes électriques des aéronefs à des températures de fonctionnement comprises entre -75 °C et 150 °C.
Les manchons peuvent être fournis avec un adhésif préenduit. Pour connaître les options disponibles, s’adresser aux fabricants/fournisseurs. L’Annexe A (informative) comporte un guide de la compatibilité des adhésifs.
Ces manchons sont normalement fournis dans les styles et les dimensions indiqués dans les Tableau 1 à Tableau 22 de l’EN 4840-002. La couleur est habituellement le noir.
Des styles et dimensions autres que ceux listés dans les Tableau 1 à Tableau 22 de l’EN 4840-002 peuvent être disponibles en tant qu’articles personnalisés. Ces articles doivent être considérés comme conformes à la présente norme s’ils répondent aux exigences de propriétés présentées dans le Tableau 1, exception faite des dimensions.

Aeronavtika - Toplotno skrčljive ulite forme - 102. del: Elastomerne, poltoge, temperaturno območje –75 do 150 °C - Standard za proizvod

Ta evropski standard določa zahtevane lastnosti za toplotno skrčljive škornje iz poltogih elastomerov za uporabo v letalskih električnih sistemih pri delovni temperaturi med –75 °C in 150 °C. Ulite forme so lahko predhodno premazane z lepilom. Za možnosti se je treba obrniti na proizvajalca/dobavitelja. Vodnik po združljivosti lepil je podan v dodatku A (informativni). Te ulite forme so običajno dobavljene z oblikami in dimenzijami, podanimi v standardu EN 4840-002 (preglednicah od 1 do 22). Običajno so črne barve. Oblike in dimenzije, ki niso posebej navedene v standardu EN 4840-002 (preglednicah od 1 do 22), so morda na voljo kot elementi po meri. Ti elementi bodo obravnavani kot skladni s tem standardom, če so skladni z zahtevami za lastnosti, navedenimi v preglednici 1, razen z zahtevami za dimenzije.

General Information

Status
Published
Publication Date
03-Dec-2019
Withdrawal Date
29-Jun-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
04-Dec-2019
Completion Date
04-Dec-2019

Buy Standard

Standard
EN 4840-102:2020
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN 4840-102:2020
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 4840-102:2020
01-februar-2020
Aeronavtika - Toplotno skrčljive ulite forme - 102. del: Elastomerne, poltoge,
temperaturno območje –75 do 150 °C - Standard za proizvod
Aerospace series - Heat shrinkable moulded shapes - Part 102: Elastomeric, semi-rigid,
temperature range -75 to 150 °C - Product Standard
Luft- und Raumfahrt - Wärmeschrumpfende Formteile - Teil 102: Elastomer, halbsteif,
Temperaturbereich -75 °C bis 120 °C - Produktnorm
Série aérospatiale - Manchons thermorétractables - Partie 102 : Semi-rigides en
élastomère, plage de température de -75 à 150 °C - Norme de produit
Ta slovenski standard je istoveten z: EN 4840-102:2019
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
SIST EN 4840-102:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 4840-102:2020

---------------------- Page: 2 ----------------------
SIST EN 4840-102:2020


EN 4840-102
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2019
EUROPÄISCHE NORM
ICS 49.060
English Version

Aerospace series - Heat shrinkable moulded shapes - Part
102: Elastomeric, semi-rigid, temperature range -75 to 150
°C - Product Standard
Série aérospatiale - Manchons thermorétractables - Luft- und Raumfahrt - Wärmeschrumpfende Formteile
Partie 102 : Semi-rigides en élastomère, plage de - Teil 102: Elastomer, halbsteif, Temperaturbereich -75
températures de -75 °C à 150 °C - Norme de produit °C bis 120 °C - Produktnorm
This European Standard was approved by CEN on 13 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4840-102:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 4840-102:2020
EN 4840-102:2019 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Required characteristics . 4
5 Quality assurance . 9
6 Designation . 9
7 Labelling and packaging . 9
8 Technical specification . 9
Annex A (informative) Adhesive compatibility guide for EN 4840-102 moulded shapes . 10

2

---------------------- Page: 4 ----------------------
SIST EN 4840-102:2020
EN 4840-102:2019 (E)
European foreword
This document (EN 4840-102:2019) has been prepared by the Aerospace and Defence Industries
Association of Euro
...

SLOVENSKI STANDARD
SIST EN 4840-102:2020
01-februar-2020
Aeronavtika - Toplotno skrčljive ulite forme - 102. del: Elastomerne, poltoge,
temperaturno območje –75 do 150 °C - Standard za proizvod
Aerospace series - Heat shrinkable moulded shapes - Part 102: Elastomeric, semi-rigid,
temperature range -75 to 150 °C - Product Standard
Luft- und Raumfahrt - Wärmeschrumpfende Formteile - Teil 102: Elastomer, halbsteif,
Temperaturbereich -75 °C bis 120 °C - Produktnorm
Série aérospatiale - Manchons thermorétractables - Partie 102 : Semi-rigides en
élastomère, plage de température de -75 à 150 °C - Norme de produit
Ta slovenski standard je istoveten z: EN 4840-102:2019
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
SIST EN 4840-102:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 4840-102:2020

---------------------- Page: 2 ----------------------
SIST EN 4840-102:2020


EN 4840-102
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2019
EUROPÄISCHE NORM
ICS 49.060
English Version

Aerospace series - Heat shrinkable moulded shapes - Part
102: Elastomeric, semi-rigid, temperature range -75 to 150
°C - Product Standard
Série aérospatiale - Manchons thermorétractables - Luft- und Raumfahrt - Wärmeschrumpfende Formteile
Partie 102 : Semi-rigides en élastomère, plage de - Teil 102: Elastomer, halbsteif, Temperaturbereich -75
température de -75 à 150 °C - Norme de produit °C bis 120 °C - Produktnorm
This European Standard was approved by CEN on 13 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4840-102:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 4840-102:2020
EN 4840-102:2019 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Required characteristics . 4
5 Quality assurance . 9
6 Designation . 9
7 Labelling and packaging . 9
8 Technical specification . 9
Annex A (informative) Adhesive compatibility guide for EN 4840-102 moulded shapes . 10

2

---------------------- Page: 4 ----------------------
SIST EN 4840-102:2020
EN 4840-102:2019 (E)
European foreword
This document (EN 4840-102:2019) has been prepared by the Aerospace and Defence Industries
Association of Europe -
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.