EN 4533-002:2017
(Main)Aerospace series - Fibre optic systems - Handbook - Part 002: Test and measurement
Aerospace series - Fibre optic systems - Handbook - Part 002: Test and measurement
This handbook examines the requirements to enable accurate measurement of fibre optic links from start of life and during the life cycle of the system from installation and through-service. Part 2 will explain the issues associated with optical link measurement and provide techniques to address these issues. This document discusses the measurement of key parameters associated with the passive layer (i.e. transmission of light through an optical harness). It does not discuss systems tests e.g. bit error rates.
Luft- und Raumfahrt - Faseroptische Systemtechnik - Handbuch - Teil 002: Tests und Messung
Série aérospatiale - Systèmes des fibres optiques - Manuel d'utilisation - Partie 002: Essais et mesures
Aeronavtika - Sistemi iz optičnih vlaken - Priročnik - 002. del: Preskušanje in merjenje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.PHUMHQMHLuft- und Raumfahrt - Faseroptische Systemtechnik - Handbuch - Teil 002: Tests und MessungenSérie aérospatiale - Systèmes des fibres optiques - Manuel d'utilisation - Partie 002: Essais et mesuresAerospace series - Fibre optic systems - Handbook - Part 002: Test and measurement49.060Aerospace electric equipment and systems33.180.01VSORãQRFibre optic systems in generalICS:Ta slovenski standard je istoveten z:EN 4533-002:2017SIST EN 4533-002:2018en,fr,de01-marec-2018SIST EN 4533-002:2018SLOVENSKI
STANDARDSIST EN 4533-002:20091DGRPHãþD
SIST EN 4533-002:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4533-002
December
t r s y ICS
v {ä r x r Supersedes EN
v w u uæ r r tã t r r xEnglish Version
Aerospace series æ Fibre optic systems æ Handbook æ Part
r r tã Test and measurement Série aérospatiale æ Systèmes des fibres optiques æ Manuel d 5utilisation æ Partie
r r tã Essais et mesures
Luftæ und Raumfahrt æ Faseroptische Systemtechnik æ Handbuch æ Teil
r r tã Tests und Messungen This European Standard was approved by CEN on
t u July
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v w u uæ r r tã t r s y ESIST EN 4533-002:2018
EN 4533-002:2017 (E) 2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Fibre types . 5 4 Test and measurement: key parameters . 7 5 Test and measurement in single-mode systems . 13 6 Test and measurement in multi-mode systems . 13 7 Testing network paths: reflectometry and footprinting . 25 8 General considerations for test and measurement in fibre optic systems . 32 9 Practical testing techniques . 36 10 Reporting arrangements . 46 11 Techniques for system design . 46 12 Appendix: Matrices . 50
SIST EN 4533-002:2018
EN 4533-002:2017 (E) 3 European foreword This document (EN 4533-002:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.