EN 61300-2-51:2007

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-51: Tests - Fibre optic connector test for transmission with applied tensile load - Singlemode and multimode

This part of IEC 61300 describes a test to quantitatively assess the capability of fibre optic connector terminated fibre assemblies to withstand static tensile loads without uncoupling of the connector, physical damage to the assembly or degradation of optical performance. This test is intended to apply to fibre assemblies using any of the following: Media type 1: reinforced jacketed cordage of any diameter, Media type 2: cable with 900 m buffer coating that may or may not be reinforced or Media type 3: connectors terminating fibre with 250 m coating.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-51: Prüfungen - Prüfung für Lichtwellenleiter-Steckverbinder mit angelegter Zugkraft - Einmoden und Mehrmoden

Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures - Partie 2-51: Essais - Essai des connecteurs à fibres optiques en transmission lorsqu'une charge de traction est appliquée - Unimodal et multimodal

La présente partie de la CEI 61300 décrit un essai destiné à évaluer de façon quantitative la capacité de l'assemblage d'une fibre optique munie de connecteurs à supporter des charges de traction statiques sans désaccouplage du connecteur, sans détérioration physique de l'ensemble, et sans dégradation des performances optiques. Cet essai est destiné à être appliqué aux assemblages de fibres employant un des supports suivants: Support de type 1: cordon de diamètre quelconque avec gaine renforcée, Support de type 2: câble avec revêtement de protection de 900 m qui peut être renforcé ou non, ou Support de type 3: fibre munie de connecteurs avec un revêtement de 250 m.

Osnovno preskušanje in merilni postopki - 2-51. del: Preskusi – Preskus optičnega konektorja za prenos ob uporabni natezni obremenitvi - Enorodni in večrodni (IEC 61300-2-51:2007)

General Information

• Status: Published
• Publication Date: 02-Aug-2007
• Withdrawal Date: 30-Jun-2010
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: CLC/TC 86BXA - Fibre optic interconnect, passive and connectorised components
• Drafting Committee: IEC/SC 86B - IEC_SC_86B
• Parallel Committee: IEC/SC 86B - IEC_SC_86B
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 03-Aug-2007
• Completion Date: 03-Aug-2007
• Ref Project: SIST EN 61300-2-51:2007 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-51: Tests - Fibre optic connector test for transmission with applied tensile load - Singlemode and multimode

Relations

• Corrected By: EN 61300-2-51:2007/AC:2015 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-51: Tests - Fibre optic connector test for transmission with applied tensile load - Singlemode and multimode
• Effective Date: 20-Jan-2015

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2007
2VQRYQRSUHVNXãDQMHLQPHULOQLSRVWRSNL±GHO3UHVNXVL±3UHVNXV
RSWLþQHJDNRQHNWRUMD]DSUHQRVREXSRUDEQLQDWH]QLREUHPHQLWYL±(QRURGQLLQ
YHþURGQL,(&
Basic test and measurement procedures -- Part 2-51: Tests - Fibre optic connector test
for transmission with applied tensile load - singlemode and multimode (IEC 61300-2-
51:2007)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-51: Prüfungen - Prüfung für Lichtwellenleiter-Steckverbinder mit
angelegter Zugkraft - Einmoden und Mehrmoden (IEC 61300-2-51:2007)
Dispositifs d'interconnexion et composants passifs a fibres optiques - Méthodes
fondamentales d'essais et de mesures -- Partie 2-51 : Essais - Essai des connecteurs a
fibres optiques en transmission lorsqu'une charge de traction est appliquée - Unimodal et
multimodal (IEC 61300-2-51:2007)
Ta slovenski standard je istoveten z: EN 61300-2-51:2007
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61300-2-51
NORME EUROPÉENNE
August 2007
EUROPÄISCHE NORM
ICS 33.180.20
English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-51: Tests -
Fibre optic connector test for transmission with applied tensile load -
Singlemode and multimode
(IEC 61300-2-51:2007)
Dispositifs d'interconnexion et Lichtwellenleiter -
composants passifs à fibres optiques - Verbindungselemente
Méthodes fondamentales d'essais und passive Bauteile -
et de mesures - Grundlegende Prüf- und Messverfahren -
Partie 2-51: Essais - Teil 2-51: Prüfungen -
Essai des connecteurs à fibres optiques Prüfung für Lichtwellenleiter-
en transmission lorsqu'une charge Steckverbinder mit angelegter Zugkraft -
de traction est appliquée - Einmoden und Mehrmoden
Unimodal et multimodal (IEC 61300-2-51:2007)
(CEI 61300-2-51:2007)
This European Standard was approved by CENELEC on 2007-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-51:2007 E
Foreword
The text of document 86B/2510/FDIS, future edition 1 of IEC 61300-2-51, prepared by SC 86B, Fibre
optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-51 on 2007-07-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-07-01
Annex ZA has been added by CENELEC.
__________
Notice
This document contains material that is Copyright © 2006, Telcordia Technologies, Inc. ("Telcordia").
All rights reserved.
The reader is advised that this IEC document and Telcordia source(s) may differ, and the context and use
of said material in this IEC document may differ from that of Telcordia. Telcordia makes no representation
or warranty, express or implied, with respect to the sufficiency, accuracy, or utility of any information or
opinion contained herein. Any use of or reliance upon said information or opinion is at the risk of the user.
Telcordia shall not be liable for any damage or injury incurred by any person arising out of the sufficiency,
accuracy, or utility of any information or opinion contained herein.
__________
Endorsement notice
The text of the International Standard IEC 61300-2-51:2007 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61300-2-51:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

1) 2)
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 2003
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
1) 2)
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 2005
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination
1) 2)
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 2003
passive components - Basic test and
measurement procedures -
Part 3-6: Examinations and measurements -
Return loss
1) 2)
IEC 61300-3-34 - Fibre optic interconnecting devices and EN 61300-3-34 2002
passive components - Basic test and
measurement procedures -
Part 3-34: Examinations and measurements -
Attenuation of random mated connectors

1)
Undated reference.
2)
Valid edition at date of issue.

INTERNATIONAL IEC
STANDARD
CEI
61300-2-51
NORME
First edition
INTERNATIONALE
Première édition
2007-06
Fibre optic interconnecting
devices and passive components –
Basic test and measurement procedures –
Part 2-51:
Tests –
Fibre optic connector test for
transmission with applied tensile load –
Singlemode and multimode
Dispositifs d’interconnexion et
composants passifs à fibres optiques –
Méthodes fondamentales d’essais et de mesures –
Partie 2-51:
Essais –
Essai des connecteurs à fibres
optiques en transmission lorsqu’une
charge de traction est appliquée –
Unimodal et multimodal
PRICE CODE
H
CODE PRIX
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
Pour prix, voir catalogue en vigueur

– 2 – 61300-2-51 © IEC:2007
CONTENTS
FOREWORD.3

1 Scope.5
2 Normative references.5
3 General description.5
4 Apparatus.5
5 Procedure.7
5.1 General .7
5.2 Preparation of specimen .7
5.3 Preconditioning.7
5.4 Initial measurements .7
5.5 Test method .7
5.6 Recovery .8
5.7 Final measurements .8
6 Details to be specified.8

Figure 1 – Test apparatus for transmission with applied tensile load .6
Figure 2 – Application of the load in the case of duplex cordage .6

Table 1 – Preferred tensile loads and angles for transmission with applied load .7

61300-2-51 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-51: Tests – Fibre optic connector test for transmission
with applied tensile load – Singlemode and multimode

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61300-2-51 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics
The text of this standard is based on the following documents:
FDIS Report on voting
86B/2510/FDIS 86B/2544/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – 61300-2-51 © IEC:2007
A list of all parts of the IEC 61300 series, published under the general title Fibre optic
interconnecting devices and passive components – Basic test and measurement procedures,
can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
___________
NOTICE
This document contains material that is Copyright © 2006, Telcordia Technologies, Inc.
("Telcordia"). All rights reserved.
The reader is advised that this IEC document and Telco
...