iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60794-1-1:1999

(Main)

Optical fibre cables - Part 1-1: Generic specification - General

Optical fibre cables - Part 1-1: Generic specification - General

Applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Establishes uniform generic requirements for the geometrical, transmission, material, mechanical, ageing and climatic properties of optical fibre cables, and electrical requirements.

Lichtwellenleiterkabel - Teil 1-1: Fachgrundspezifikation - Allgemeines

Câbles à fibres optiques - Partie 1-1: Spécification générique - Généralités

Applicable aux câbles à fibres optiques destinés à être utilisés dans les équipements de télécommunication et les dispositifs utilisant des techniques analogues, ainsi qu'aux câbles constitués de fibres optiques et de conducteurs électriques. Etablit des prescriptions génériques uniformes relatives à l'établissement des caractéristiques géométriques, de transmission, de matériaux, mécaniques, de vieillissement et climatiques des câbles à fibres optiques, ainsi que des prescriptions électriques.

Optical fibre cables - Part 1-1: General specification - General (IEC 60794-1-1:1999)

General Information

Status
Withdrawn
Publication Date
12-Aug-1999
Withdrawal Date
31-Jul-2002
ICS
33.180.10 - Fibres and cables
Technical Committee
CLC/TC 86A - Optical fibres and optical fibre cables
Drafting Committee
IEC/SC 86A - IEC_SC_86A
Parallel Committee
IEC/SC 86A - IEC_SC_86A
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Dec-2004
Completion Date
01-Dec-2004
Ref Project
SIST EN 60794-1-1:2001 - Optical fibre cables -- Part 1-1: Generic specification - General (IEC 60794-1-1:1999)

Relations

Replaced By
EN 60794-1-1:2002 - Optical fibre cables - Part 1-1: Generic specification - General
Effective Date
29-Jan-2023

Buy Standard

EN 60794-1-1:2001EN 60794-1-1:2001
PreviousNext
Standard
EN 60794-1-1:2001
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Optical fibre cables - Part 1-1: General specification - General (IEC 60794-1-1:1999)Lichtwellenleiterkabel -- Teil 1-1: Fachgrundspezifikation - AllgemeinesCâbles à fibres optiques -- Partie 1-1: Spécification générique - GénéralitésOptical fibre cables -- Part 1-1: Generic specification - General (IEC 60794-1-1:1999)33.180.10Fibres and cablesICS:Ta slovenski standard je istoveten z:EN 60794-1-1:1999SIST EN 60794-1-1:2001en01-februar-2001SIST EN 60794-1-1:2001SLOVENSKI
STANDARD



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001



SIST EN 60794-1-1:2001


...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60794-2-23:2024(Main)
Optical fibre cables - Part 2-23: Indoor cables - Detail specification for multi-fibre cables for use in MPO connector terminated cable assemblies
SIST EN IEC 60794-2-23:2024

IEC 60794-2-23: 2024 is a detail specification and specifies indoor multi-fibre cables for use in MPO (multi-fibre push on) connector terminated cable assemblies.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-312:2024(Main)
Optical fibre cables - Part 1-312: Generic specification - Basic optical cable test procedures - Cable element test methods - Elongation test for buffer tubes at low temperature, Method G11B
SIST EN IEC 60794-1-312:2024

IEC 60794-1-312: 2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at low temperature. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces method G11B of IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) alignment of the title with the content of the method.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-311:2024(Main)
Optical fibre cables - Part 1-311: Generic specification - Basic optical cable test procedures - Cable element test methods - Tensile strength and elongation test for cable elements, Method G11A
SIST EN IEC 60794-1-311:2024

IEC 60794-1-311:2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at break. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) The information about dumb-bells is removed because this is not used for testing cable elements; b) the parameters strain at yield and E modulus are added in 5.7.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-2-24:2024(Main)
Optical fibre cables - Part 2-24: Indoor cables - Detail specification for multiple multi-fibre unit cables for use in MPO connector terminated breakout cable assemblies
SIST EN IEC 60794-2-24:2024

IEC 60794-2-24:2024 is a detail specification and specifies indoor multiple multi-fibre unit cables for use in MPO (multi-fibre push on) connector terminated breakout cable assemblies.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-306:2023(Main)
Optical fibre cables - Part 1-306: Generic specification - Basic optical cable test procedures - Cable element test methods - Ribbon torsion, Method G6
SIST EN IEC 60794-1-306:2023

IEC 60794-1-306: 2023 describes test procedures to verify the mechanical and functional integrity of the fibre ribbon structure. The test determines the capability of the ribbon to withstand torsion without delamination between optical fibre and ribbon bonding agent. This document applies to optical fibre ribbons in optical cables for use with telecommunication equipment and devices employing similar techniques, and to optical fibre ribbons in cables having a combination of both optical fibres and electrical conductors. This document is not applicable to partially-bonded ribbons. The method for partially-bonded ribbons is under consideration. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. NOTE The environmental testing of optical fibre ribbon would be valuable for some applications. Useful information about suitable test methods can be found in the optical fibre standards IEC 60793-1-50, IEC 60793-1-51, IEC 60793‑1‑52, and IEC 60793-1-53. This document partially cancels and replaces IEC 60794‑1‑23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) change the scope, not include partially-bonded ribbon; b) add some details to the procedure.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-111:2023(Main)
Optical fibre cables - Part 1-111: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Bend, method E11
SIST EN IEC 60794-1-111:2023

IEC 60794-1-111: 2023 defines the test procedure to determine the ability of an optical fibre cable to withstand bending around a test mandrel. The primary purpose of this procedure is to measure the change in attenuation when the cable is bent around a test mandrel. A secondary purpose is to assess whether the cable has been physically damaged by bending. NOTE 1 This test can be utilized at any specified temperature, including the low or high temperature limits for the cable. NOTE 2 The bend test procedure for cable elements is specified in IEC 60794-1-301, method G1. This document partially cancels and replaces IEC 60794-1-21:2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794‑1‑21:2015: a) the nominal sample length was newly specified as 10 m between the cable element fixing points at both ends, unless otherwise specified; b) the number of turns on the mandrel in Figure 1 for the single-helix configuration were corrected to match the number of turns shown in the figure for the two-helix configuration; c) requirements on the turnaround loop were added for method E11A, two-helix configuration; d) the turnaround loop with the same diameter as the mandrel was taken into account for calculation of the number of turns of each helix for method E11A, two-helix configuration; e) added a formula for calculation of the number of revolutions in each helix for method E11A, two-helix configuration; f) added a description for the procedure when the turnaround loop diameter is larger than the mandrel diameter for method E11A, two-helix configuration; g) all the figures were updated and the different components labelled; h) added the attenuation monitoring equipment in 4.2 for the apparatus and the description to measure the change in attenuation in the test methods E11A and E11B; i) added Clause 9 for details to be reported; j) added Annex A showing an example of a special mandrel to perform the bend test according to method E11A, two-helix configuration; k) added Annex B providing the rationale for the options of method E11A, two-helix configuration.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60793-1-44:2023(Main)
Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength
SIST EN IEC 60793-1-44:2023

IEC 60793-1-44:2023 establishes uniform requirements for measuring the cut-off wavelength of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. This document gives methods for measuring the cut-off wavelength for uncabled or cabled single mode telecom fibre. These procedures apply to all category B and C fibre types. There are three methods of deployment for measuring the cut-off wavelength: - method A: cable cut-off using uncabled fibre 22 m long sample, lcc; - method B: cable cut-off using cabled fibre 22 m long sample, lcc; - method C: fibre cut-off using uncabled fibre 2 m long sample, lc. All methods require a reference measurement. There are two reference-scan techniques, either or both of which can be used with all methods: - bend-reference technique; - multimode-reference technique using category A1(OM1-OM5) multimode fibre. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) used the diameter of the fibre loops to describe deployment; b) added Annex D related to cut-off curve artifacts; c) reorganized information and added more figures to clarify concepts.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-1:2023(Main)
Optical fibre cables - Part 1-1: Generic specification - General
SIST EN IEC 60794-1-1:2023

IEC 60794-1-1:2023 applies to optical fibre cables for use with communication equipment and devices employing similar techniques. Electrical properties are specified for optical ground wire (OPGW) and optical phase conductor (OPPC) cables. Hybrid communication cables are specified in the IEC 62807 series. The object of this document is to establish uniform generic requirements for the geometrical, transmission, material, mechanical, ageing (environmental exposure), climatic and electrical properties of optical fibre cables and cable elements, where appropriate. This fifth edition cancels and replaces the fourth edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) reorganization of the document to a more logical flow making it easier for the reader: b) expansion of the tables to include names and definitions of all documents in the IEC 60794‑x series; c) expansion of the definitions, graphical symbols, terminology and abbreviations content, with the aim of making this document the default and reference for all others in the IEC 60794‑x series; d) inclusion of updated, reorganized and expanded optical fibre, attenuation and bandwidth subclauses, with the aim of making this document the default and reference for all others in the IEC 60794-x series.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-1-309:2023(Main)
Optical fibre cables - Part 1-309: Generic specification - Basic optical cable test procedures - Cable element test methods - Bleeding and evaporation of filling or flooding compounds, Method G9
SIST EN IEC 60794-1-309:2023

IEC 60794-1-309:2023 describes the test procedures to be used in establishing uniform requirements for optical fibre cable elements, filling compounds or flooding compounds, for the environmental property-bleeding and evaporation. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. NOTE Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This first edition of IEC 60794-1-309 cancels and replaces method G9 of the second edition of IEC 60794-1-23 published in 2019. This edition includes the following significant technical changes with respect to the previous edition: a) the optical cable element test methods contained in IEC 60794-1-23:2019 will now be individually numbered in the IEC 60794-1-3xx series. Each test method is now considered to be an individual document rather than part of a multi-test method compendium. Full cross-reference details are given in IEC 60794-1-2; b) the scope is broadened so that the test method is also applicable for flooding compounds; c) the cover of the test set-up is cancelled.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60794-2-50:2023(Main)
Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies
SIST EN IEC 60794-2-50:2023

IEC 60794-2-50:2023 is available as IEC 60794-2-50:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60794-2-50:2023 specifies requirements for simplex and duplex optical fibre cables for use in terminated cable assemblies or as used for termination of passive components. This third edition cancels and replaces the second edition published in 2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) added IEC 60793-1-46 and IEC 60794-1-211 to the normative references; b) changed the load duration for the tensile test from 5 min to 10 min; c) clarified the distance between the clamps for torsion test to 125 times cable diameter, but not less than 0,3 m; d) recommended the temperatures –10 °C and +60 °C for indoor simplex and duplex cables and included the low and high temperatures for category C, CHD, OP and OPHD according to the operating service environments in IEC 61753-1 for temperature cycling and shrinkage testing; e) updated the shrinkage test standard to IEC 60794-1-211, F11A, and changed the requirement to maximum 20 mm; f) replaced the text for the fire performance with an improved description.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day