Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-10: Tests - Crush and load resistance

IEC 61300-2-10:2021 is available as IEC 61300-2-10:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61300-2-10:2021 evaluates the effect of loads which is possible to occur when fibre optic devices are exposed to critical situations such as being stepped on, being run over by vehicle tyres, when an evenly-distributed static load is applied to the top surface of a street cabinet or when a load is applied to a street cabinet's open door. This third edition cancels and replaces the second edition published in 2012. This edition includes the following significant technical changes with respect to the previous edition: - addition of testing an evenly distributed static load applied on the top surface of a street cabinet; - addition of testing a static load applied to a street cabinet door; - addition of descriptions to perform the test at a specified temperature other as specified in the standard atmospheric conditions and addition of test temperature(s) in Table 1; - update of the severities according to IEC 61753-1:2018.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-10: Prüfungen - Querdruck- und Lastbeständigkeit

Dispositifs d’interconnexion et composants passifs fibroniques - Procédures fondamentales d’essais et de mesures - Partie 2-10: Essais - Résistance à la compression et à la charge

IEC 61300-2-10:2021 est disponible sous forme de IEC 61300-2-10:2021 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61300-2-10:2021 évalue les effets des charges susceptibles de se produire lorsque les dispositifs fibroniques sont exposés à des situations critiques telles que le piétinement ou l’écrasement par des pneus de véhicules, lorsqu’une charge statique répartie uniformément est appliquée à la surface supérieure d’une armoire d’environnement urbain ou lorsqu’une charge est appliquée sur la porte ouverte d’une armoire d’environnement urbain. Cette troisième édition annule et remplace la deuxième édition parue en 2012. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - ajout d’un essai avec une charge statique répartie uniformément à la surface supérieure d’une armoire d’environnement urbain; - ajout d’un essai avec une charge statique appliquée sur la porte d’une armoire d’environnement urbain; - ajout de descriptions pour effectuer l'essai à une température spécifiée autre que celle spécifiée dans les conditions atmosphériques normales et ajout de la (des) température(s) d'essai dans le Tableau 1; - mise à jour des sévérités conformément à l’IEC 61753-1:2018.

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-10. del: Preskusi - Odpornost proti drobljenju in obremenitvi (IEC 61300-2-10:2021)

General Information

Status
Published
Publication Date
15-Apr-2021
Current Stage
6060 - Document made available - Publishing
Start Date
16-Apr-2021
Completion Date
16-Apr-2021

Relations

Buy Standard

Standard
EN IEC 61300-2-10:2021
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 61300-2-10:2013
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-10. del: Preskusi - Odpornost proti drobljenju in obremenitvi (IEC
61300-2-10:2021)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-10: Tests - Crush and load resistance (IEC 61300-2-
10:2021)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-10: Prüfungen - Querdruckbeständigkeit (IEC 61300-2-10:2021)
Dispositifs d’interconnexion et composants passifs fibroniques - Procédures
fondamentales d’essais et de mesures - Partie 2-10: Essais - Résistance à la
compression et à la charge (IEC 61300-2-10:2021)
Ta slovenski standard je istoveten z: EN IEC 61300-2-10:2021
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-2-10

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 33.180.20 Supersedes EN 61300-2-10:2012 and all of its
amendments and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-10: Tests -
Crush and load resistance
(IEC 61300-2-10:2021)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren –
mesures - Partie 2-10: Essais - Résistance à la Teil 2-10: Prüfungen - Querdruck- und Lastbeständigkeit
compression et à la charge (IEC 61300-2-10:2021)
(IEC 61300-2-10:2021)
This European Standard was approved by CENELEC on 2021-04-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-2-10:2021 E

European foreword
The text of document 86B/4405/FDIS, future edition 3 of IEC 61300-2-10, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-10:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-01-06
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-06
document have to be withdrawn
This document supersedes EN 61300-2-10:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-10:2021 was approved by CENELEC as a
European Standard without any modification.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-2-38 - Fibre optic interconnecting devices and EN 61300-2-38 -
passive components - Basic test and
measurement procedures - Part 2-38:
Tests - Sealing for pressurized fibre optic
closures
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures - Part 3-4:
Examinations and measurements -
Attenuation
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures - Part 3-6:
Examinations and measurements - Return
loss
IEC 61753-1 - Fibre optic interconnecting devices and EN IEC 61753-1 -
passive components - Performance
standard - Part 1: General and guidance

IEC 61300-2-10 ®
Edition 3.0 2021-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-10: Tests – Crush and load resistance

Dispositifs d’interconnexion et composants passifs fibroniques – Procédures

fondamentales d’essais et de mesures –

Partie 2-10: Essais – Résistance à la compression et à la charge

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-9507-6

– 2 – IEC 61300-2-10:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 6
5 Apparatus . 6
5.1 General . 6
5.2 Plate or ground . 6
5.3 Pad . 6
5.4 Force generator . 6
5.5 Gauge . 6
5.6 Temperature chamber . 6
6 Procedure . 10
6.1 DUT preparation . 10
6.2 Pre-conditioning . 10
6.3 Initial examination and measurement . 10
6.4 Device mounting . 10
6.5 Conditioning . 10
6.6 Recovery . 10
6.7 Final examination and measurement . 10
7 Severity . 11
8 Details to be specified . 11

Figure 1 – Crush apparatus . 7
Figure 2 – Apparatus for an evenly distributed load applied to the top surface of a
street cabinet – Front view . 7
Figure 3 – Apparatus for an evenly distributed load applied to the top surface of a
street cabinet – Top view . 8
Figure 4 – Apparatus for load applied to a street cabinet door – Front view . 9
Figure 5 – Apparatus for load applied to a street cabinet door – Top view . 9

Table 1 – Severities . 11

IEC 61300-2-10:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-10: Tests – Crush and load resistance

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.