ETSI EN 302 500-1 V1.2.1 (2008-06)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra WideBand (UWB) technology; Location Tracking equipment operating in the frequency range from 6 GHz to 8,5 GHz; Part 1: Technical characteristics and test methods
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra WideBand (UWB) technology; Location Tracking equipment operating in the frequency range from 6 GHz to 8,5 GHz; Part 1: Technical characteristics and test methods
REN/ERM-TG31C-257-1
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB) tehnologijo - Oprema za sledenje, ki deluje v frekvenčnem območju od 6 GHz do 8,5 GHz - 1. del: Tehnične karakteristike in preskusne metode
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) using Ultra WideBand (UWB) technology - Location Tracking equipment operating in the frequency range from 6 GHz to 8,5 GHz - Part 1: Technical characteristics and test methods33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:EN 302 500-1 Version 1.2.1SIST EN 302 500-1 V1.2.1:2008en01-oktober-2008SIST EN 302 500-1 V1.2.1:2008SLOVENSKI
STANDARD
SIST EN 302 500-1 V1.2.1:2008
ETSI EN 302 500-1 V1.2.1 (2008-06)European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Short Range Devices (SRD) usingUltra WideBand (UWB) technology;Location Tracking equipment operating inthe frequency range from 6 GHz to 8,5 GHz;Part 1: Technical characteristics andtest methods
SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 2
Reference REN/ERM-TG31C-257-1 Keywords radio, regulation, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 3
Contents Intellectual Property Rights.5 Foreword.5 1 Scope.7 2 References.7 2.1 Normative references.7 2.2 Informative references.8 3 Definitions, symbols and abbreviations.8 3.1 Definitions.8 3.2 Symbols.9 3.3 Abbreviations.9 4 Technical requirement specifications.9 4.1 General requirements.9 4.2 Presentation of equipment for testing purposes.9 4.2.1 Choice of model for testing.10 4.2.1.1 Auxiliary test equipment.10 4.2.1.2 Declarations by the provider.10 4.3 Mechanical and electrical design.10 4.3.1 General.10 4.3.2 Controls.10 4.3.3 Transmitter shut-off facility.10 4.3.4 Marking.10 4.3.4.1 Equipment identification.10 4.3.4.2 Additional information for the user.10 4.4 Other device emissions.11 5 Test conditions, power sources and ambient temperatures.11 5.1 Normal and extreme test conditions.11 5.2 Test power source.11 5.2.1 External test power source.11 5.2.2 Internal test power source.11 5.3 Normal test conditions.12 5.3.1 Normal temperature and humidity.12 5.3.2 Normal test power source.12 5.3.2.1 Mains voltage.12 5.3.2.2 Regulated lead-acid battery power sources.12 5.3.2.3 Other power sources.12 6 General conditions.12 6.1 Normal test signals.12 6.2 Test sites and general arrangements for radiated measurements.12 6.3 Modes of operation of the transmitter.13 7 Interpretation of results.13 7.1 Measurement uncertainty.13 7.1.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty.14 7.1.2 Measurement uncertainty is greater than maximum acceptable uncertainty.14 7.2 Other emissions from device circuitry.14 8 Methods of measurement and limits for transmitter parameters.15 8.1 General.15 8.2 Maximum mean e.i.r.p. spectral density.15 8.2.1 Definition.15 8.2.2 Methods of measurement.15 8.2.3 Limits.16 8.3 Frequency of highest maximum mean e.i.r.p. spectral density.16 SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 4
8.3.1 Definition.16 8.3.2 Methods of measurement.16 8.3.3 Limits.16 8.4 Maximum peak e.i.r.p.16 8.4.1 Definition.16 8.4.2 Methods of measurement.17 8.4.3 Limits.17 8.5 Minimum Pulse Repetition Frequency (PRF).18 8.5.1 Definitions.18 8.5.2 Declaration.18 8.5.3 Limits.18 9 Methods of measurement and limits for receiver parameters.18 9.1 Receiver spurious emissions.18 9.1.1 Definition.18 9.1.2 Test procedure.18 9.1.3 Limit.19 Annex A (normative): Radiated measurement.20 A.1 Test sites and general arrangements for measurements involving the use of radiated fields.20 A.1.1 Anechoic chamber.20 A.1.2 Anechoic chamber with a conductive ground plane.21 A.1.3 Test antenna.22 A.1.4 Substitution antenna.23 A.2 Guidance on the use of radiation test sites.23 A.2.1 Verification of the test site.23 A.2.2 Preparation of the EUT.23 A.2.3 Power supplies to the EUT.23 A.2.4 Range length.24 A.2.5 Site preparation.24 A.2.6 General requirements for RF cables.25 A.3 Coupling of signals.25 A.3.1 General.25 A.3.2 Data Signals.25 A.4 Standard test position.25 A.5 Standard test methods.26 A.5.1 Calibrated setup.26 A.5.2 Substitution method.26 A.6 Standard calibration method.27 Annex B (normative): Technical performance of the spectrum analyser.30 Annex C (normative): Additional design requirements.31 C.1 Operation.31 C.2 Receipt-of-reception-acknowledgement.31 Annex D (informative): Measurement antenna and preamplifier specifications.32 Annex E (informative): Calculation of peak limit for 3 MHz measurement bandwidth.33 Annex F (informative): Bibliography.35 History.36
SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 5
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document is part 1 of a multi-part deliverable covering Short Range Devices (SRD) using Ultra WideBand (UWB) technology; Location Tracking equipment operating in the frequency range from 6 GHz to 8,5 GHz, as identified below: Part 1: "Technical characteristics and test methods"; Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive". Clauses 1 and 3 provide a general description on the types of equipment covered by the present document and the definitions and abbreviations used. Clause 4 provides a guide as to the number of samples required in order that type tests may be carried out, and any markings on the equipment which the provider shall provide. Clauses 5 and 6 give guidance on the test and general conditions for testing of the device. Clause 7 gives the interpretation of results and maximum measurement uncertainty values. Clause 8 specifies the transmitter spectrum utilization parameters which are required to be measured. The clauses provide details on how the equipment should be tested and the conditions which should be applied. Clause 9 specifies the receiver spectrum utilization parameters which are required to be measured. The clauses provide details on how the equipment should be tested and the conditions which should be applied. Annex A (normative) provides specifications concerning radiated measurements. Annex B (normative) provides information on the spectrum analyser specification. Annex C (normative) provides information on additional design requirements for equipment covered by the present document. Annex D (informative) provides information on measurement antenna and preamplifier specifications. Annex E (informative) provides information on peak measurements within a 3 MHz measurement bandwidth. Annex F (informative) covers other supplementary information.
SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 6
National transposition dates Date of adoption of this EN: 27 June 2008 Date of latest announcement of this EN (doa): 30 September 2008 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2009 Date of withdrawal of any conflicting National Standard (dow): 31 March 2009
SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 7
1 Scope The present document specifies the requirements for ultra-wideband location tracking equipment operating in all or part of the frequency range from 6 GHz to 8,5 GHz. The present document applies for indoor as well as portable or mobile outdoor applications. It covers ultra-wideband location tracking tags which are attached to people or objects and tags are tracked using a fixed receiver infrastructure to only receive the UWB emission emitted by the tags. Equipment covered by the present document is fitted with an integral or dedicated antenna. The present document contains the technical characteristics and test methods for location tracking equipment and it does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • Non-specific reference may be made only to a complete document or a part thereof and only in the following cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document;
- for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. [1] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [2] CISPR 16-1-1 (2006): "Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus". [3] ANSI C63.5 (2006): "American National Standard for Calibration of Antennas Used for Radiated Emission Measurements in Electro Magnetic Interference". SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 8
2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. [i.1] CENELEC EN 55022:2006: "Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement". [i.2] ITU-R Recommendation SM.1754: "Measurement techniques of ultra-wideband transmissions". [i.3] ETSI EN 300 220 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW". [i.4] ETSI EN 300 440 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range". [i.5] ETSI TR 102 070-2 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide to the application of harmonized standards to multi-radio and combined radio and non-radio equipment; Part 2: Effective use of the radio frequency spectrum". [i.6] ETSI TR 102 273 (V1.2.1) (all parts): "Electromagnetic compatibility and Radio Spectrum Matters (ERM): Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties". [i.7] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: dedicated antenna: removable antenna supplied and tested with the radio equipment, designed as an indispensable part of the equipment fixed-mounted station: station which is fixed mounted and which is not intended to be operated while in motion; however, it behaves otherwise in the system like a mobile station impulsive UWB signal: radiated, short transient ultra-wideband signal whose occupied bandwidth is defined by its time duration rather than by frequency-hopping or other techniques integral antenna: antenna designed to be connected to the equipment without the use of a standard connector and considered to be part of the equipment NOTE: An integral antenna may be fitted internally or externally to the equipment. Mobile Station (MS): station intended to be used while in motion or during halts at unspecified points portable station: mobile station that is portable but cannot comfortably be carried around by a person due to weight and/or size or having relatively high power consumption provider: manufacturer or his authorized representative or the person responsible for placing on the market pulse: radiated short transient UWB signal whose time duration is nominally the reciprocal of its -10 dB bandwidth NOTE: See ITU-R Recommendation SM.1754 [i.2]. radiated measurements: measurements which involve the absolute measurement of a radiated field SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 9
Ultra WideBand (UWB): equipment incorporating, as an integral part or as an accessory, technology for short-range radiocommunication, involving the intentional generation and transmission of radio-frequency energy that spreads over a frequency range wider than 50 MHz, which may overlap several frequency bands allocated to radiocommunication services 3.2 Symbols For the purposes of the present document, the following symbols apply: dB decibel R distance λ wavelength 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: e.i.r.p. equivalent isotropically radiated power EMC ElectroMagnetic Compatibility EUT Equipment Under Test LNA Low Noise Amplifier MS Mobile Station PRF Pulse Repetition Frequency R&TTE Radio and Telecommunications Terminal Equipment RBW Resolution BandWidth RF Radio Frequency rms root mean square SNR Signal to Noise Ratio SRD Short Range Device TX Transmitter UWB Ultra WideBand VBW Video BandWidth VSWR Voltage Standing Wave Ratio 4 Technical requirement specifications 4.1 General requirements Equipment supplied for testing against the present document shall be fitted with either an integral antenna or a dedicated antenna. 4.2 Presentation of equipment for testing purposes Each equipment submitted for testing shall fulfil the requirements of the present document on all frequencies over which it is intended to operate. To simplify and harmonize the testing procedures between the different testing laboratories, measurements shall be performed, according to the present document, on samples of equipment defined in clause 4.2.1. These clauses are intended to give confidence that the requirements set out in the present document have been met without the necessity of performing measurements on all frequencies. SIST EN 302 500-1 V1.2.1:2008
ETSI ETSI EN 302 500-1 V1.2.1 (2008-06) 10
4.2.1 Choice of model for testing The provider shall provide one or more samples of the equipment, as appropriate, for testing. If an equipment has several optional features, considered not to affect the RF parameters then tests need only be performed on the equipment configured with that combination of features considered to be the most complex, as proposed by the provider and agreed by the test laboratory. 4.2.1.1 Auxiliary test equipment All necessary test signal sources, setting up instructions and other product information shall accompany the equipment when it is submitted for testing. 4.2.1.2 Declarations by the provider The provider shall declare the necessar
...
ETSI EN 302 500-1 V1.2.1 (2008-06)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD) using
Ultra WideBand (UWB) technology;
Location Tracking equipment operating in
the frequency range from 6 GHz to 8,5 GHz;
Part 1: Technical characteristics and
test methods
---------------------- Page: 1 ----------------------
2 ETSI EN 302 500-1 V1.2.1 (2008-06)
Reference
REN/ERM-TG31C-257-1
Keywords
radio, regulation, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 500-1 V1.2.1 (2008-06)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope.7
2 References.7
2.1 Normative references.7
2.2 Informative references.8
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.9
3.3 Abbreviations.9
4 Technical requirement specifications.9
4.1 General requirements.9
4.2 Presentation of equipment for testing purposes.9
4.2.1 Choice of model for testing .10
4.2.1.1 Auxiliary test equipment .10
4.2.1.2 Declarations by the provider .10
4.3 Mechanical and electrical design.10
4.3.1 General.10
4.3.2 Controls.10
4.3.3 Transmitter shut-off facility.10
4.3.4 Marking.10
4.3.4.1 Equipment identification.10
4.3.4.2 Additional information for the user.10
4.4 Other device emissions.11
5 Test conditions, power sources and ambient temperatures .11
5.1 Normal and extreme test conditions .11
5.2 Test power source.11
5.2.1 External test power source.11
5.2.2 Internal test power source .11
5.3 Normal test conditions.12
5.3.1 Normal temperature and humidity.12
5.3.2 Normal test power source .12
5.3.2.1 Mains voltage.12
5.3.2.2 Regulated lead-acid battery power sources .12
5.3.2.3 Other power sources.12
6 General conditions.12
6.1 Normal test signals .12
6.2 Test sites and general arrangements for radiated measurements .12
6.3 Modes of operation of the transmitter .13
7 Interpretation of results .13
7.1 Measurement uncertainty.13
7.1.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty.14
7.1.2 Measurement uncertainty is greater than maximum acceptable uncertainty.14
7.2 Other emissions from device circuitry.14
8 Methods of measurement and limits for transmitter parameters .15
8.1 General.15
8.2 Maximum mean e.i.r.p. spectral density.15
8.2.1 Definition.15
8.2.2 Methods of measurement.15
8.2.3 Limits.16
8.3 Frequency of highest maximum mean e.i.r.p. spectral density.16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 500-1 V1.2.1 (2008-06)
8.3.1 Definition.16
8.3.2 Methods of measurement.16
8.3.3 Limits.16
8.4 Maximum peak e.i.r.p.16
8.4.1 Definition.16
8.4.2 Methods of measurement.17
8.4.3 Limits.17
8.5 Minimum Pulse Repetition Frequency (PRF) .18
8.5.1 Definitions.18
8.5.2 Declaration.18
8.5.3 Limits.18
9 Methods of measurement and limits for receiver parameters.18
9.1 Receiver spurious emissions.18
9.1.1 Definition.18
9.1.2 Test procedure.18
9.1.3 Limit.19
Annex A (normative): Radiated measurement.20
A.1 Test sites and general arrangements for measurements involving the use of radiated fields .20
A.1.1 Anechoic chamber.20
A.1.2 Anechoic chamber with a conductive ground plane.21
A.1.3 Test antenna.22
A.1.4 Substitution antenna.23
A.2 Guidance on the use of radiation test sites .23
A.2.1 Verification of the test site .23
A.2.2 Preparation of the EUT.23
A.2.3 Power supplies to the EUT.23
A.2.4 Range length.24
A.2.5 Site preparation.24
A.2.6 General requirements for RF cables .25
A.3 Coupling of signals.25
A.3.1 General.25
A.3.2 Data Signals.25
A.4 Standard test position .25
A.5 Standard test methods.26
A.5.1 Calibrated setup.26
A.5.2 Substitution method.26
A.6 Standard calibration method.27
Annex B (normative): Technical performance of the spectrum analyser.30
Annex C (normative): Additional design requirements.31
C.1 Operation.31
C.2 Receipt-of-reception-acknowledgement.31
Annex D (informative): Measurement antenna and preamplifier specifications .32
Annex E (informative): Calculation of peak limit for 3 MHz measurement bandwidth.33
Annex F (informative): Bibliography.35
History .36
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 500-1 V1.2.1 (2008-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document is part 1 of a multi-part deliverable covering Short Range Devices (SRD) using
Ultra WideBand (UWB) technology; Location Tracking equipment operating in the frequency range from 6 GHz to
8,5 GHz, as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Clauses 1 and 3 provide a general description on the types of equipment covered by the present document and the
definitions and abbreviations used.
Clause 4 provides a guide as to the number of samples required in order that type tests may be carried out, and any
markings on the equipment which the provider shall provide.
Clauses 5 and 6 give guidance on the test and general conditions for testing of the device.
Clause 7 gives the interpretation of results and maximum measurement uncertainty values.
Clause 8 specifies the transmitter spectrum utilization parameters which are required to be measured. The clauses
provide details on how the equipment should be tested and the conditions which should be applied.
Clause 9 specifies the receiver spectrum utilization parameters which are required to be measured. The clauses provide
details on how the equipment should be tested and the conditions which should be applied.
Annex A (normative) provides specifications concerning radiated measurements.
Annex B (normative) provides information on the spectrum analyser specification.
Annex C (normative) provides information on additional design requirements for equipment covered by the present
document.
Annex D (informative) provides information on measurement antenna and preamplifier specifications.
Annex E (informative) provides information on peak measurements within a 3 MHz measurement bandwidth.
Annex F (informative) covers other supplementary information.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 500-1 V1.2.1 (2008-06)
National transposition dates
Date of adoption of this EN: 27 June 2008
Date of latest announcement of this EN (doa): 30 September 2008
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2009
Date of withdrawal of any conflicting National Standard (dow): 31 March 2009
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 500-1 V1.2.1 (2008-06)
1 Scope
The present document specifies the requirements for ultra-wideband location tracking equipment operating in all or part
of the frequency range from 6 GHz to 8,5 GHz.
The present document applies for indoor as well as portable or mobile outdoor applications.
It covers ultra-wideband location tracking tags which are attached to people or objects and tags are tracked using a fixed
receiver infrastructure to only receive the UWB emission emitted by the tags. Equipment covered by the present
document is fitted with an integral or dedicated antenna.
The present document contains the technical characteristics and test methods for location tracking equipment and it
does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the
optimum performance achievable.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[2] CISPR 16-1-1 (2006): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus".
[3] ANSI C63.5 (2006): "American National Standard for Calibration of Antennas Used for Radiated
Emission Measurements in Electro Magnetic Interference".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 500-1 V1.2.1 (2008-06)
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] CENELEC EN 55022:2006: "Information technology equipment - Radio disturbance
characteristics - Limits and methods of measurement".
[i.2] ITU-R Recommendation SM.1754: "Measurement techniques of ultra-wideband transmissions".
[i.3] ETSI EN 300 220 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency
range with power levels ranging up to 500 mW".
[i.4] ETSI EN 300 440 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range".
[i.5] ETSI TR 102 070-2 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Guide to the application of harmonized standards to multi-radio and combined radio and non-radio
equipment; Part 2: Effective use of the radio frequency spectrum".
[i.6] ETSI TR 102 273 (V1.2.1) (all parts): "Electromagnetic compatibility and Radio Spectrum Matters
(ERM): Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties".
[i.7] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
dedicated antenna: removable antenna supplied and tested with the radio equipment, designed as an indispensable part
of the equipment
fixed-mounted station: station which is fixed mounted and which is not intended to be operated while in motion;
however, it behaves otherwise in the system like a mobile station
impulsive UWB signal: radiated, short transient ultra-wideband signal whose occupied bandwidth is defined by its
time duration rather than by frequency-hopping or other techniques
integral antenna: antenna designed to be connected to the equipment without the use of a standard connector and
considered to be part of the equipment
NOTE: An integral antenna may be fitted internally or externally to the equipment.
Mobile Station (MS): station intended to be used while in motion or during halts at unspecified points
portable station: mobile station that is portable but cannot comfortably be carried around by a person due to weight
and/or size or having relatively high power consumption
provider: manufacturer or his authorized representative or the person responsible for placing on the market
pulse: radiated short transient UWB signal whose time duration is nominally the reciprocal of its -10 dB bandwidth
NOTE: See ITU-R Recommendation SM.1754 [i.2].
radiated measurements: measurements which involve the absolute measurement of a radiated field
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 302 500-1 V1.2.1 (2008-06)
Ultra WideBand (UWB): equipment incorporating, as an integral part or as an accessory, technology for short-range
radiocommunication, involving the intentional generation and transmission of radio-frequency energy that spreads over
a frequency range wider than 50 MHz, which may overlap several frequency bands allocated to radiocommunication
services
3.2 Symbols
For the purposes of the present document, the following symbols apply:
dB decibel
R distance
λ wavelength
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
e.i.r.p. equivalent isotropically radiated power
EMC ElectroMagnetic Compatibility
EUT Equipment Under Test
LNA Low Noise Amplifier
MS Mobile Station
PRF Pulse Repetition Frequency
R&TTE Radio and Telecommunications Terminal Equipment
RBW Resolution BandWidth
RF Radio Frequency
rms root mean square
SNR Signal to Noise Ratio
SRD Short Range Device
TX Transmitter
UWB Ultra WideBand
VBW Video BandWidth
VSWR Voltage Standing Wave Ratio
4 Technical requirement specifications
4.1 General requirements
Equipment supplied for testing against the present document shall be fitted with either an integral antenna or a
dedicated antenna.
4.2 Presentation of equipment for testing purposes
Each equipment submitted for testing shall fulfil the requirements of the present document on all frequencies over
which it is intended to operate.
To simplify and harmonize the testing procedures between the different testing laboratories, measurements shall be
performed, according to the present document, on samples of equipment defined in clause 4.2.1.
These clauses are intended to give confidence that the requirements set out in the present document have been met
without the necessity of performing measurements on all frequencies.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 302 500-1 V1.2.1 (2008-06)
4.2.1 Choice of model for testing
The provider shall provide one or more samples of the equipment, as appropriate, for testing.
If an equipment has several optional features, considered not to affect the RF parameters then tests need only be
performed on the equipment configured with that combination of features considered to be the most complex, as
proposed by the provider and agreed by the test laboratory.
4.2.1.1 Auxiliary test equipment
All necessary test signal sources, setting up instructions and other product information shall accompany the equipment
when it is submitted for testing.
4.2.1.2 Declarations by the provider
The provider shall declare the necessary information regarding the equipment with respect to all technical requirements
set by the present document.
4.3 Mechanical and electri
...
Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD) using
Ultra WideBand (UWB) technology;
Location Tracking equipment operating in
the frequency range from 6 GHz to 8,5 GHz;
Part 1: Technical characteristics and
test methods
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
Reference
REN/ERM-TG31C-257-1
Keywords
radio, regulation, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope.7
2 References.7
2.1 Normative references.7
2.2 Informative references.8
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.9
3.3 Abbreviations.9
4 Technical requirement specifications.9
4.1 General requirements.9
4.2 Presentation of equipment for testing purposes.9
4.2.1 Choice of model for testing .9
4.2.1.1 Auxiliary test equipment .10
4.2.1.2 Declarations by the provider .10
4.3 Mechanical and electrical design.10
4.3.1 General.10
4.3.2 Controls.10
4.3.3 Transmitter shut-off facility.10
4.3.4 Marking.10
4.3.4.1 Equipment identification.10
4.3.4.2 Additional information for the user.10
4.4 Other device emissions.11
5 Test conditions, power sources and ambient temperatures .11
5.1 Normal and extreme test conditions .11
5.2 Test power source.11
5.2.1 External test power source.11
5.2.2 Internal test power source .11
5.3 Normal test conditions.12
5.3.1 Normal temperature and humidity.12
5.3.2 Normal test power source .12
5.3.2.1 Mains voltage.12
5.3.2.2 Regulated lead-acid battery power sources .12
5.3.2.3 Other power sources.12
6 General conditions.12
6.1 Normal test signals .12
6.2 Test sites and general arrangements for radiated measurements .12
6.3 Modes of operation of the transmitter .13
7 Interpretation of results .13
7.1 Measurement uncertainty.13
7.1.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty.14
7.1.2 Measurement uncertainty is greater than maximum acceptable uncertainty.14
7.2 Other emissions from device circuitry.14
8 Methods of measurement and limits for transmitter parameters .15
8.1 General.15
8.2 Maximum mean e.i.r.p. spectral density.15
8.2.1 Definition.15
8.2.2 Methods of measurement.15
8.2.3 Limits.16
8.3 Frequency of highest maximum mean e.i.r.p. spectral density.16
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
8.3.1 Definition.16
8.3.2 Methods of measurement.16
8.3.3 Limits.16
8.4 Maximum peak e.i.r.p.16
8.4.1 Definition.16
8.4.2 Methods of measurement.17
8.4.3 Limits.17
8.5 Minimum Pulse Repetition Frequency (PRF) .18
8.5.1 Definitions.18
8.5.2 Declaration.18
8.5.3 Limits.18
9 Methods of measurement and limits for receiver parameters.18
9.1 Receiver spurious emissions.18
9.1.1 Definition.18
9.1.2 Test procedure.18
9.1.3 Limit.19
Annex A (normative): Radiated measurement.20
A.1 Test sites and general arrangements for measurements involving the use of radiated fields .20
A.1.1 Anechoic chamber.20
A.1.2 Anechoic chamber with a conductive ground plane.21
A.1.3 Test antenna.22
A.1.4 Substitution antenna.23
A.2 Guidance on the use of radiation test sites .23
A.2.1 Verification of the test site .23
A.2.2 Preparation of the EUT.23
A.2.3 Power supplies to the EUT.23
A.2.4 Range length.24
A.2.5 Site preparation.24
A.2.6 General requirements for RF cables .25
A.3 Coupling of signals.25
A.3.1 General.25
A.3.2 Data Signals.25
A.4 Standard test position .25
A.5 Standard test methods.26
A.5.1 Calibrated setup.26
A.5.2 Substitution method.26
A.6 Standard calibration method.27
Annex B (normative): Technical performance of the spectrum analyser.30
Annex C (normative): Additional design requirements.31
C.1 Operation.31
C.2 Receipt-of-reception-acknowledgement.31
Annex D (informative): Measurement antenna and preamplifier specifications .32
Annex E (informative): Calculation of peak limit for 3 MHz measurement bandwidth.33
Annex F (informative): Bibliography.35
History .36
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document is part 1 of a multi-part deliverable covering Short Range Devices (SRD) using
Ultra WideBand (UWB) technology; Location Tracking equipment operating in the frequency range from
6 GHz to 8,5 GHz, as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Clauses 1 and 3 provide a general description on the types of equipment covered by the present document and the
definitions and abbreviations used.
Clause 4 provides a guide as to the number of samples required in order that type tests may be carried out, and any
markings on the equipment which the provider shall provide.
Clauses 5 and 6 give guidance on the test and general conditions for testing of the device.
Clause 7 gives the interpretation of results and maximum measurement uncertainty values.
Clause 8 specifies the transmitter spectrum utilization parameters which are required to be measured. The clauses
provide details on how the equipment should be tested and the conditions which should be applied.
Clause 9 specifies the receiver spectrum utilization parameters which are required to be measured. The clauses provide
details on how the equipment should be tested and the conditions which should be applied.
Annex A (normative) provides specifications concerning radiated measurements.
Annex B (normative) provides information on the spectrum analyser specification.
Annex C (normative) provides information on additional design requirements for equipment covered by the present
document.
Annex D (informative) provides information on measurement antenna and preamplifier specifications.
Annex E (informative) provides information on peak measurements within a 3 MHz measurement bandwidth.
Annex F (informative) covers other supplementary information.
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
1 Scope
The present document specifies the requirements for ultra-wideband location tracking equipment operating in all or part
of the frequency range from 6 GHz to 8,5 GHz.
The present document applies for indoor as well as portable or mobile outdoor applications.
It covers ultra-wideband location tracking tags which are attached to people or objects and tags are tracked using a fixed
receiver infrastructure to only receive the UWB emission emitted by the tags. Equipment covered by the present
document is fitted with an integral or dedicated antenna.
The present document contains the technical characteristics and test methods for location tracking equipment and it
does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the
optimum performance achievable.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[2] CISPR 16-1-1 (2006): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus".
[3] ANSI C63.5 (2006): "American National Standard for Calibration of Antennas Used for Radiated
Emission Measurements in Electro Magnetic Interference".
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[4] CENELEC EN 55022:2006: "Information technology equipment - Radio disturbance
characteristics - Limits and methods of measurement".
[5] ITU-R Recommendation SM.1754: "Measurement techniques of ultra-wideband transmissions".
[6] ETSI EN 300 220 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency
range with power levels ranging up to 500 mW".
[7] ETSI EN 300 440 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range".
[8] ETSI TR 102 070-2 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Guide to the application of harmonized standards to multi-radio and combined radio and non-radio
equipment; Part 2: Effective use of the radio frequency spectrum".
[9] ETSI TR 102 273 (V1.2.1) (all parts): "Electromagnetic compatibility and Radio Spectrum Matters
(ERM): Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties".
[10] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
dedicated antenna: removable antenna supplied and tested with the radio equipment, designed as an indispensable part
of the equipment
fixed-mounted station: station which is fixed mounted and which is not intended to be operated while in motion;
however, it behaves otherwise in the system like a mobile station
impulsive UWB signal: radiated, short transient ultra-wideband signal whose occupied bandwidth is defined by its
time duration rather than by frequency-hopping or other techniques
integral antenna: antenna designed to be connected to the equipment without the use of a standard connector and
considered to be part of the equipment
NOTE: An integral antenna may be fitted internally or externally to the equipment.
Mobile Station (MS): station intended to be used while in motion or during halts at unspecified points
portable station: mobile station that is portable but cannot comfortably be carried around by a person due to weight
and/or size or having relatively high power consumption
provider: manufacturer or his authorized representative or the person responsible for placing on the market
pulse: radiated short transient UWB signal whose time duration is nominally the reciprocal of its -10 dB bandwidth
NOTE: See ITU-R Recommendation SM.1754 [5].
radiated measurements: measurements which involve the absolute measurement of a radiated field
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
Ultra WideBand (UWB): equipment incorporating, as an integral part or as an accessory, technology for short-range
radiocommunication, involving the intentional generation and transmission of radio-frequency energy that spreads over
a frequency range wider than 50 MHz, which may overlap several frequency bands allocated to radiocommunication
services
3.2 Symbols
For the purposes of the present document, the following symbols apply:
dB decibel
R distance
λ wavelength
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
e.i.r.p. equivalent isotropically radiated power
EMC ElectroMagnetic Compatibility
EUT Equipment Under Test
LNA Low Noise Amplifier
MS Mobile Station
PRF Pulse Repetition Frequency
R&TTE Radio and Telecommunications Terminal Equipment
RBW Resolution BandWidth
RF Radio Frequency
rms root mean square
SNR Signal to Noise Ratio
SRD Short Range Device
TX Transmitter
UWB Ultra WideBand
VBW Video BandWidth
VSWR Voltage Standing Wave Ratio
4 Technical requirement specifications
4.1 General requirements
Equipment supplied for testing against the present document shall be fitted with either an integral antenna or a
dedicated antenna.
4.2 Presentation of equipment for testing purposes
Each equipment submitted for testing shall fulfil the requirements of the present document on all frequencies over
which it is intended to operate.
To simplify and harmonize the testing procedures between the different testing laboratories, measurements shall be
performed, according to the present document, on samples of equipment defined in clause 4.2.1.
These clauses are intended to give confidence that the requirements set out in the present document have been met
without the necessity of performing measurements on all frequencies.
4.2.1 Choice of model for testing
The provider shall provide one or more samples of the equipment, as appropriate, for testing.
ETSI
---------------------- Page: 9 ----------------------
10 Final draft ETSI EN 302 500-1 V1.2.1 (2008-04)
If an equipment has several optional features, considered not to affect the RF parameters then tests need only be
performed on the equipment configured with that combination of features considered to be the most complex, as
proposed by the provider and agreed by the test laboratory.
4.2.1.1 Auxiliary test equipment
All necessary test signal sources, setting up instructions and other product information shall accompany the equipment
when it is submitted for testing.
4.2.1.2 Declarations by t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.