ETSI EN 301 908-2 V4.2.1 (2010-03)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 2: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 2: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive
REN/ERM-TFES-004-2
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Bazne postaje (BS), ponavljalniki (repetitorji) in uporabniška oprema (UE) za celična omrežja tretje generacije IMT-2000 - 2. del: Harmonizirani EN za IMT-2000, CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD in E-UTRA FDD) (UE), ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Pričujoči dokument velja za naslednje vrste radijske opreme:
uporabniško opremo za IMT-2000 CDMA z neposrednim razprševanjem (ULTRA FDD in E-ULTRA FDD). Te vrste radijske opreme so zmožne delovanja v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v tabeli 1-1.
Pričujoči dokument zajema zahteve za UTRA FDD uporabniško opremo iz 3GPP izdaje 99, 4, 5, 6, 7 in 8 ter E-UTRA FDD uporabniško opremo izdaje 8. Pričujoči dokument zajema zahteve za UTRA FDD uporabniško opremo v pasovih delovanja, določenih v TS 102 735 [i.4]. Pričujoči dokument je namenjen temu, da zajema določbe Direktive 1999/5/ES (direktive R&TTE)[i.2], člena 3.2, ki navaja, da » … je radijska oprema narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«. Poleg pričujočega dokumenta, se ostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2], lahko uporabljajo za opremo znotraj področja uporabe pričujočega dokumenta.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 2: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-2 Version 4.2.1SIST EN 301 908-2 V4.2.1:2010en01-maj-2010SIST EN 301 908-2 V4.2.1:2010SLOVENSKI
STANDARD
SIST EN 301 908-2 V4.2.1:2010
ETSI EN 301 908-2 V4.2.1 (2010-03)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS), Repeaters and User Equipment (UE)for IMT-2000 Third-Generation cellular networks;Part 2: Harmonized EN for IMT-2000,CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)covering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 2
Reference REN/ERM-TFES-004-2 Keywords 3G, 3GPP, cellular, digital, IMT-2000, mobile, radio, regulation, UMTS, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 11 3.3 Abbreviations . 11 4 Technical requirements specifications . 12 4.1 Environmental profile . 12 4.2 Conformance requirements . 12 4.2.1 Introduction. 12 4.2.2 Transmitter maximum output power. 13 4.2.2.1 Definition . 13 4.2.2.2 Limits . 13 4.2.2.3 Conformance . 13 4.2.3 Transmitter spectrum emission mask . 13 4.2.3.1 Definition . 13 4.2.3.2 Limits . 14 4.2.3.3 Conformance . 14 4.2.4 Transmitter spurious emissions . 14 4.2.4.1 Definition . 14 4.2.4.2 Limits . 14 4.2.4.3 Conformance . 15 4.2.5 Transmitter minimum output power . 16 4.2.5.1 Definition . 16 4.2.5.2 Limits . 16 4.2.5.3 Conformance . 16 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 16 4.2.6.1 Definition . 16 4.2.6.2 Limits . 16 4.2.6.3 Conformance . 16 4.2.7 Receiver blocking characteristics . 17 4.2.7.1 Definition . 17 4.2.7.2 Limits . 17 4.2.7.3 Conformance . 18 4.2.8 Receiver spurious response . 18 4.2.8.1 Definition . 18 4.2.8.2 Limits . 18 4.2.8.3 Conformance . 18 4.2.9 Receiver intermodulation characteristics . 19 4.2.9.1 Definition . 19 4.2.9.2 Limits . 19 4.2.9.3 Conformance . 19 4.2.10 Receiver spurious emissions . 19 4.2.10.1 Definition . 19 4.2.10.2 Limits . 20 4.2.10.3 Conformance . 21 4.2.11 Out-of-synchronization handling of output power . 21 4.2.11.1 Definition . 21 SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 4 4.2.11.2 Limits . 21 4.2.11.3 Conformance . 22 4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 22 4.2.12.1 Definition . 22 4.2.12.2 Limits . 22 4.2.12.3 Conformance . 23 5 Testing for compliance with technical requirements . 23 5.1 Environmental conditions for testing . 23 5.2 Interpretation of the measurement results . 23 5.3 Essential radio test suites . 24 5.3.1 Transmitter maximum output power. 24 5.3.1.1 Method of test . 24 5.3.1.1.1 Initial conditions . 24 5.3.1.1.2 Procedure . 24 5.3.1.2 Test requirements . 25 5.3.2 Transmitter spectrum emission mask . 25 5.3.2.1 Method of test . 25 5.3.2.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 25 5.3.2.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 25 5.3.2.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 25 5.3.2.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 25 5.3.2.2 Test requirements . 25 5.3.3 Transmitter spurious emissions . 26 5.3.3.1 Method of test . 26 5.3.3.1.1 Initial conditions . 26 5.3.3.1.2 Procedure . 26 5.3.3.2 Test requirements . 26 5.3.4 Transmitter minimum output power . 26 5.3.4.1 Method of test . 26 5.3.4.1.1 Initial conditions . 26 5.3.4.1.2 Procedure . 26 5.3.4.2 Test requirements . 26 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 27 5.3.5.1 Method of test . 27 5.3.5.1.1 Initial conditions . 27 5.3.5.1.2 Procedure . 27 5.3.5.2 Test requirements . 27 5.3.6 Receiver blocking characteristics . 27 5.3.6.1 Method of test . 27 5.3.6.1.1 Initial requirements . 27 5.3.6.1.2 Procedure . 28 5.3.6.2 Test requirements . 28 5.3.7 Receiver spurious response . 28 5.3.7.1 Method of test . 28 5.3.7.1.1 Initial conditions . 28 5.3.7.1.2 Procedure . 28 5.3.7.2 Test requirements . 28 5.3.8 Receiver Intermodulation characteristics . 28 5.3.8.1 Method of test . 28 5.3.8.1.1 Initial conditions . 28 5.3.8.1.2 Procedure . 29 5.3.8.2 Test requirements . 29 5.3.9 Receiver spurious emissions . 29 5.3.9.1 Method of test . 29 5.3.9.1.1 Initial conditions . 29 5.3.9.1.2 Procedure . 29 5.3.9.2 Test requirements . 29 5.3.10 Out-of-synchronization handling of output power . 29 5.3.10.1 Method of test . 29 5.3.10.1.1 Initial conditions . 29 5.3.10.1.2 Procedure . 30 SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 5 5.3.10.2 Test requirements . 30 5.3.11 Transmitter adjacent channel leakage power ratio . 30 5.3.11.1 Method of test . 30 5.3.11.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 30 5.3.11.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 31 5.3.11.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 31 5.3.11.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 31 5.3.11.2 Test requirements . 31 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 32 Annex B (normative): Environmental profile . 34 B.1 General . 34 B.1.1 Introduction . 34 B.1.2 Temperature . 34 B.1.3 Voltage . 34 B.1.4 Test environment . 35 Annex C (informative): The EN title in the official languages . 36 Annex D (informative): Bibliography . 37 History . 38
SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive"). Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A. The present document is part 2 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below: Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 7 Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 19 February 2010 Date of latest announcement of this EN (doa): 31 May 2010 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2010 Date of withdrawal of any conflicting National Standard (dow): 30 November 2011
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-2 V4.2.1:2010
ETSI ETSI EN 301 908-2 V4.2.1 (2010-03) 8 1 Scope The present document applies
...
ETSI EN 301 908-2 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 2: Harmonized EN for IMT-2000,
CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-2 V4.2.1 (2010-03)
Reference
REN/ERM-TFES-004-2
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-2 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 11
4 Technical requirements specifications . 12
4.1 Environmental profile . 12
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Transmitter maximum output power. 13
4.2.2.1 Definition . 13
4.2.2.2 Limits . 13
4.2.2.3 Conformance . 13
4.2.3 Transmitter spectrum emission mask . 13
4.2.3.1 Definition . 13
4.2.3.2 Limits . 14
4.2.3.3 Conformance . 14
4.2.4 Transmitter spurious emis sions . 14
4.2.4.1 Definition . 14
4.2.4.2 Limits . 14
4.2.4.3 Conformance . 15
4.2.5 Transmitter minimum output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 16
4.2.6.3 Conformance . 16
4.2.7 Receiver blocking characteristics . 17
4.2.7.1 Definition . 17
4.2.7.2 Limits . 17
4.2.7.3 Conformance . 18
4.2.8 Receiver spurious response . 18
4.2.8.1 Definition . 18
4.2.8.2 Limits . 18
4.2.8.3 Conformance . 18
4.2.9 Receiver intermodulation characteristics . 19
4.2.9.1 Definition . 19
4.2.9.2 Limits . 19
4.2.9.3 Conformance . 19
4.2.10 Receiver spurious emissions . 19
4.2.10.1 Definition . 19
4.2.10.2 Limits . 20
4.2.10.3 Conformance . 21
4.2.11 Out-of-synchronization handling of output power . 21
4.2.11.1 Definition . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-2 V4.2.1 (2010-03)
4.2.11.2 Limits . 21
4.2.11.3 Conformance . 22
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 22
4.2.12.1 Definition . 22
4.2.12.2 Limits . 22
4.2.12.3 Conformance . 23
5 Testing for compliance with technical requirements . 23
5.1 Environmental conditions for testing . 23
5.2 Interpretation of the measurement results . 23
5.3 Essential radio test suites . 24
5.3.1 Transmitter maximum output power. 24
5.3.1.1 Method of test . 24
5.3.1.1.1 Initial conditions . 24
5.3.1.1.2 Procedure . 24
5.3.1.2 Test requirements . 25
5.3.2 Transmitter spectrum emission mask . 25
5.3.2.1 Method of test . 25
5.3.2.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 25
5.3.2.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 25
5.3.2.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 25
5.3.2.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 25
5.3.2.2 Test requirements . 25
5.3.3 Transmitter spurious emis sions . 26
5.3.3.1 Method of test . 26
5.3.3.1.1 Initial conditions . 26
5.3.3.1.2 Procedure . 26
5.3.3.2 Test requirements . 26
5.3.4 Transmitter minimum output power . 26
5.3.4.1 Method of test . 26
5.3.4.1.1 Initial conditions . 26
5.3.4.1.2 Procedure . 26
5.3.4.2 Test requirements . 26
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 27
5.3.5.1 Method of test . 27
5.3.5.1.1 Initial conditions . 27
5.3.5.1.2 Procedure . 27
5.3.5.2 Test requirements . 27
5.3.6 Receiver blocking characteristics . 27
5.3.6.1 Method of test . 27
5.3.6.1.1 Initial requirements . 27
5.3.6.1.2 Procedure . 28
5.3.6.2 Test requirements . 28
5.3.7 Receiver spurious response . 28
5.3.7.1 Method of test . 28
5.3.7.1.1 Initial conditions . 28
5.3.7.1.2 Procedure . 28
5.3.7.2 Test requirements . 28
5.3.8 Receiver Intermodulation characteristics . 28
5.3.8.1 Method of test . 28
5.3.8.1.1 Initial conditions . 28
5.3.8.1.2 Procedure . 29
5.3.8.2 Test requirements . 29
5.3.9 Receiver spurious emissions . 29
5.3.9.1 Method of test . 29
5.3.9.1.1 Initial conditions . 29
5.3.9.1.2 Procedure . 29
5.3.9.2 Test requirements . 29
5.3.10 Out-of-synchronization handling of output power . 29
5.3.10.1 Method of test . 29
5.3.10.1.1 Initial conditions . 29
5.3.10.1.2 Procedure . 30
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-2 V4.2.1 (2010-03)
5.3.10.2 Test requirements . 30
5.3.11 Transmitter adjacent channel leakage power ratio . 30
5.3.11.1 Method of test . 30
5.3.11.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 30
5.3.11.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 31
5.3.11.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 31
5.3.11.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 31
5.3.11.2 Test requirements . 31
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 32
Annex B (normative): Environmental profile . 34
B.1 General . 34
B.1.1 Introduction . 34
B.1.2 Temperature . 34
B.1.3 Voltage . 34
B.1.4 Test environment . 35
Annex C (informative): The EN title in the official languages . 36
Annex D (informative): Bibliography . 37
History . 38
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-2 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-2 V4.2.1 (2010-03)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 19 February 2010
Date of latest announcement of this EN (doa): 31 May 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2010
Date of withdrawal of any conflicting National Standard (dow): 30 November 2011
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-2 V4.2.1 (2010-03)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD and E-UTRA FDD).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA FDD operating bands
UTRA FDD Band Direction of transmission UTRA FDD operating bands
I
...
Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 2: Harmonized EN for IMT-2000,
CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
Reference
REN/ERM-TFES-004-2
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 11
4 Technical requirements specifications . 12
4.1 Environmental profile . 12
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Transmitter maximum output power. 13
4.2.2.1 Definition . 13
4.2.2.2 Limits . 13
4.2.2.3 Conformance . 13
4.2.3 Transmitter spectrum emission mask . 13
4.2.3.1 Definition . 13
4.2.3.2 Limits . 14
4.2.3.3 Conformance . 14
4.2.4 Transmitter spurious emis sions . 14
4.2.4.1 Definition . 14
4.2.4.2 Limits . 14
4.2.4.3 Conformance . 15
4.2.5 Transmitter minimum output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 16
4.2.6.3 Conformance . 16
4.2.7 Receiver blocking characteristics . 17
4.2.7.1 Definition . 17
4.2.7.2 Limits . 17
4.2.7.3 Conformance . 18
4.2.8 Receiver spurious response . 18
4.2.8.1 Definition . 18
4.2.8.2 Limits . 18
4.2.8.3 Conformance . 18
4.2.9 Receiver intermodulation characteristics . 19
4.2.9.1 Definition . 19
4.2.9.2 Limits . 19
4.2.9.3 Conformance . 19
4.2.10 Receiver spurious emissions . 19
4.2.10.1 Definition . 19
4.2.10.2 Limits . 20
4.2.10.3 Conformance . 21
4.2.11 Out-of-synchronization handling of output power . 21
4.2.11.1 Definition . 21
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
4.2.11.2 Limits . 21
4.2.11.3 Conformance . 22
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 22
4.2.12.1 Definition . 22
4.2.12.2 Limits . 22
4.2.12.3 Conformance . 23
5 Testing for compliance with technical requirements . 23
5.1 Environmental conditions for testing . 23
5.2 Interpretation of the measurement results . 23
5.3 Essential radio test suites . 24
5.3.1 Transmitter maximum output power. 24
5.3.1.1 Method of test . 24
5.3.1.1.1 Initial conditions . 24
5.3.1.1.2 Procedure . 24
5.3.1.2 Test requirements . 25
5.3.2 Transmitter spectrum emission mask . 25
5.3.2.1 Method of test . 25
5.3.2.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 25
5.3.2.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 25
5.3.2.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 25
5.3.2.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 25
5.3.2.2 Test requirements . 25
5.3.3 Transmitter spurious emis sions . 26
5.3.3.1 Method of test . 26
5.3.3.1.1 Initial conditions . 26
5.3.3.1.2 Procedure . 26
5.3.3.2 Test requirements . 26
5.3.4 Transmitter minimum output power . 26
5.3.4.1 Method of test . 26
5.3.4.1.1 Initial conditions . 26
5.3.4.1.2 Procedure . 26
5.3.4.2 Test requirements . 26
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 27
5.3.5.1 Method of test . 27
5.3.5.1.1 Initial conditions . 27
5.3.5.1.2 Procedure . 27
5.3.5.2 Test requirements . 27
5.3.6 Receiver blocking characteristics . 27
5.3.6.1 Method of test . 27
5.3.6.1.1 Initial requirements . 27
5.3.6.1.2 Procedure . 28
5.3.6.2 Test requirements . 28
5.3.7 Receiver spurious response . 28
5.3.7.1 Method of test . 28
5.3.7.1.1 Initial conditions . 28
5.3.7.1.2 Procedure . 28
5.3.7.2 Test requirements . 28
5.3.8 Receiver Intermodulation characteristics . 28
5.3.8.1 Method of test . 28
5.3.8.1.1 Initial conditions . 28
5.3.8.1.2 Procedure . 29
5.3.8.2 Test requirements . 29
5.3.9 Receiver spurious emissions . 29
5.3.9.1 Method of test . 29
5.3.9.1.1 Initial conditions . 29
5.3.9.1.2 Procedure . 29
5.3.9.2 Test requirements . 29
5.3.10 Out-of-synchronization handling of output power . 29
5.3.10.1 Method of test . 29
5.3.10.1.1 Initial conditions . 29
5.3.10.1.2 Procedure . 30
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
5.3.10.2 Test requirements . 30
5.3.11 Transmitter adjacent channel leakage power ratio . 30
5.3.11.1 Method of test . 30
5.3.11.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 30
5.3.11.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 31
5.3.11.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 31
5.3.11.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 31
5.3.11.2 Test requirements . 31
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 32
Annex B (normative): Environmental profile . 34
B.1 General . 34
B.1.1 Introduction . 34
B.1.2 Temperature . 34
B.1.3 Voltage . 34
B.1.4 Test environment . 35
Annex C (informative): The EN title in the official languages . 36
Annex D (informative): Bibliography . 37
History . 38
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-2 V4.1.2 (2009-12)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD and E-UTRA FDD).
These radio equipment types are capable of op
...
Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 2: Harmonized EN for IMT-2000,
CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
Reference
REN/ERM-TFES-004-2
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 11
4 Technical requirements specifications . 12
4.1 Environmental profile . 12
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Transmitter maximum output power. 12
4.2.2.1 Definition . 12
4.2.2.2 Limits . 13
4.2.2.3 Conformance . 13
4.2.3 Transmitter spectrum emission mask . 13
4.2.3.1 Definition . 13
4.2.3.2 Limits . 14
4.2.3.3 Conformance . 14
4.2.4 Transmitter spurious emis sions . 14
4.2.4.1 Definition . 14
4.2.4.2 Limits . 14
4.2.4.3 Conformance . 15
4.2.5 Transmitter minimum output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 16
4.2.6.3 Conformance . 16
4.2.7 Receiver blocking characteristics . 17
4.2.7.1 Definition . 17
4.2.7.2 Limits . 17
4.2.7.3 Conformance . 18
4.2.8 Receiver spurious response . 19
4.2.8.1 Definition . 19
4.2.8.2 Limits . 19
4.2.8.3 Conformance . 19
4.2.9 Receiver intermodulation characteristics . 19
4.2.9.1 Definition . 19
4.2.9.2 Limits . 19
4.2.9.3 Conformance . 20
4.2.10 Receiver spurious emissions . 20
4.2.10.1 Definition . 20
4.2.10.2 Limits . 20
4.2.10.3 Conformance . 21
4.2.11 Out-of-synchronization handling of output power . 22
4.2.11.1 Definition . 22
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
4.2.11.2 Limits . 22
4.2.11.3 Conformance . 23
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 23
4.2.12.1 Definition . 23
4.2.12.2 Limits . 23
4.2.12.3 Conformance . 24
5 Testing for compliance with technical requirements . 24
5.1 Environmental conditions for testing . 24
5.2 Interpretation of the measurement results . 24
5.3 Essential radio test suites . 25
5.3.1 Transmitter maximum output power. 25
5.3.1.1 Method of test . 25
5.3.1.1.1 Initial conditions . 25
5.3.1.1.2 Procedure . 26
5.3.1.2 Test requirements . 26
5.3.2 Transmitter spectrum emission mask . 26
5.3.2.1 Method of test . 26
5.3.2.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 26
5.3.2.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 26
5.3.2.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 26
5.3.2.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 26
5.3.2.2 Test requirements . 26
5.3.3 Transmitter spurious emis sions . 27
5.3.3.1 Method of test . 27
5.3.3.1.1 Initial conditions . 27
5.3.3.1.2 Procedure . 27
5.3.3.2 Test requirements . 27
5.3.4 Transmitter minimum output power . 27
5.3.4.1 Method of test . 27
5.3.4.1.1 Initial conditions . 27
5.3.4.1.2 Procedure . 27
5.3.4.2 Test requirements . 27
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 28
5.3.5.1 Method of test . 28
5.3.5.1.1 Initial conditions . 28
5.3.5.1.2 Procedure . 28
5.3.5.2 Test requirements . 28
5.3.6 Receiver blocking characteristics . 28
5.3.6.1 Method of test . 28
5.3.6.1.1 Initial requirements . 28
5.3.6.1.2 Procedure . 29
5.3.6.2 Test requirements . 29
5.3.7 Receiver spurious response . 29
5.3.7.1 Method of test . 29
5.3.7.1.1 Initial conditions . 29
5.3.7.1.2 Procedure . 29
5.3.7.2 Test requirements . 29
5.3.8 Receiver Intermodulation characteristics . 29
5.3.8.1 Method of test . 29
5.3.8.1.1 Initial conditions . 29
5.3.8.1.2 Procedure . 30
5.3.8.2 Test requirements . 30
5.3.9 Receiver spurious emissions . 30
5.3.9.1 Method of test . 30
5.3.9.1.1 Initial conditions . 30
5.3.9.1.2 Procedure . 30
5.3.9.2 Test requirements . 30
5.3.10 Out-of-synchronization handling of output power . 30
5.3.10.1 Method of test . 30
5.3.10.1.1 Initial conditions . 30
5.3.10.1.2 Procedure . 31
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
5.3.10.2 Test requirements . 31
5.3.11 Transmitter adjacent channel leakage power ratio . 31
5.3.11.1 Method of test . 31
5.3.11.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 31
5.3.11.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 31
5.3.11.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 32
5.3.11.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 32
5.3.11.2 Test requirements . 32
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 33
Annex B (normative): Environmental profile . 35
B.1 General . 35
B.1.1 Introduction . 35
B.1.2 Temperature . 35
B.1.3 Voltage . 35
B.1.4 Test environment . 36
Annex C (informative): The EN title in the official languages . 37
Annex D (informative): Bibliography . 38
History . 39
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-2 V4.1.1 (2009-04)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD and E-UTRA FDD).
These radio equipment types are capable of operating in all or any part of the fr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.