ETSI TS 102 169-1 V1.1.1 (2003-02)
Services and Protocols for Advanced Networks (SPAN); Network Integration Testing between H.323, ISDN and PSTN; Part 1: Test Suite Structure and Test purposes (TSS&TP)
Services and Protocols for Advanced Networks (SPAN); Network Integration Testing between H.323, ISDN and PSTN; Part 1: Test Suite Structure and Test purposes (TSS&TP)
DTS/SPAN-130303-1
Storitve in protokoli za napredna omrežja (SPAN) – Preskušanje integracije omrežja med H.323, ISDN in PSTN – 1. del: Zgradba preskušalnega niza in namen preskušanja (TSS&TP)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2005
Storitve in protokoli za napredna omrežja (SPAN) – Preskušanje integracije
omrežja med H.323, ISDN in PSTN – 1. del: Zgradba preskušalnega niza in namen
preskušanja (TSS&TP)
Services and Protocols for Advanced Networks (SPAN) – Network Integration Testing
between H.323, ISDN and PSTN – Part 1: Test Suite Structure and Test purposes
(TSS&TP)
Ta slovenski standard je istoveten z: ETSI TS 102 169-1 V1.1.1 (2003-02)
ICS:
33.040.40 Podatkovna komunikacijska Data communication
omrežja networks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
Technical Specification
Services and Protocols for Advanced Networks (SPAN);
Network Integration Testing between H.323, ISDN and PSTN;
Part 1: Test Suite Structure and Test purposes (TSS&TP)
2 ETSI TS 102 169-1 V1.1.1 (2003-02)
Reference
DTS/SPAN-130303-1
Keywords
H.323, NIT, testing, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.org
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2003.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI TS 102 169-1 V1.1.1 (2003-02)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope.6
2 References.6
3 Definitions and abbreviations.8
3.1 Definitions.8
3.2 Abbreviations.8
4 Architecture and Test Suite Structure (TSS).9
4.1 Architecture.9
4.2 Test Suite Structure (TSS).10
4.2.1 ISDN-H.323.10
4.2.2 H.323-ISDN.10
4.2.3 PSTN-H.323.11
4.2.4 H.323-PSTN.11
4.2.5 H.323-H.323 (PC-PC).11
5 Numbering Scheme.12
6 Test purposes.13
6.1 Test purposes for ISDN-H.323 Basic call Successful -Speech .13
6.2 Test purposes for ISDN-H.323 Basic call Successful - 3,1 kHz audio.18
6.3 Test purposes for ISDN-H.323 Basic call Successful -UDI.25
6.4 Test purposes for ISDN-H.323 Basic call Unsuccessful .31
6.5 Test purposes for ISDN-H.323 Basic call Unsuccessful -UDI/TA .35
6.6 Test purposes for ISDN-H.323 Supplementary services .35
6.7 Test purposes for H.323-ISDN, Basic call, Successful speech .40
6.8 Test purposes for H.323-ISDN, Basic call, Successful 3,1 kHz.47
6.9 Test purposes for H.323-ISDN, Basic call, UDI .53
6.10 Test purposes for H.323-ISDN, Basic call, Unsuccessful .58
6.11 Test purposes for H.323- ISDN Supplementary services .60
6.12 Test purposes for H.323-PSTN, Basic call, Successful - Speech .64
6.13 Test purposes for H.323-PSTN, Basic call, Successful - 3,1 kHz audio .66
6.14 Test purposes for H.323-PSTN, Basic call, Unsuccessful.67
6.15 Test purposes for PSTN-H.323, Basic call.69
6.16 Test purposes for PSTN-H.323, Unsuccessful .70
6.17 Test purposes for H.323-H.323 Basic call, Successful.71
6.18 Test purposes for H.323-H.323 Basic call, Unsuccessful.76
Annex A (normative): Bearer capability default encoding for ISDN calling terminal
equipment and H.323 called terminal equipment (H.225 § 7.2.2.1.1) .79
A.1 Request and recognition of a circuit-mode bearer service .79
A.1.1 Circuit-mode 64 kbit/s 8 kHz structured bearer service category usable for speech information transfer .79
A.1.1.1 Request by a ISDN calling terminal equipment.79
A.1.1.2 Compatibility at the called H.323 terminal equipment .79
A.1.2 Circuit-mode 64 kbit/s unrestricted 8 kHz structured bearer service category.80
A.1.2.1 Request by a ISDN calling terminal equipment.80
A.1.2.2 Compatibility at the called H.323 terminal equipment .80
A.1.2.3 ISDN connections involving restricted 64 kbit/s transfer capability .80
A.1.2.3.1 Request by a calling ISDN terminal connected to a network supporting 64 kbit/s unrestricted
digital information transfer .80
A.1.2.3.2 Compatibility at the called H.323 terminal equipment connected to a network supporting 64
kbit/s unrestricted digital information transfer.81
A.1.2.3.3 Request by a calling ISDN terminal connected to a network supporting 64 kbit/s restricted digital
information transfer.81
ETSI
4 ETSI TS 102 169-1 V1.1.1 (2003-02)
A.1.2.3.4 Compatibility at the called H.323 terminal equipment connected to a network using restricted
digital information transfer .81
A.1.3 Circuit-mode 64 kbit/s 8 kHz structured bearer service category usable for 3,1 kHz audio information
transfer.82
A.1.3.1 Request by a ISDN calling terminal equipment.82
A.1.3.2 Compatibility at the H.323 called terminal equipment .82
History .83
ETSI
5 ETSI TS 102 169-1 V1.1.1 (2003-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
All published ETSI deliverables shall include information which directs the reader to the above source of information.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Services and Protocols for
Advanced Networks (SPAN).
The present document is part 1 of a multi-part deliverable covering the Network Integration Testing between H.323,
ISDN and PSTN, as identified below:
Part 1: "Test Suite Structure and Test purposes (TSS&TP)";
Part 2: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification".
ETSI
6 ETSI TS 102 169-1 V1.1.1 (2003-02)
1 Scope
The present document specifies the Test Suite Structure and Test Purposes (TSS&TP) for Network Integration Testing
(NIT) to verify the overall compatibility of ITU-T Recommendation H.323 [3], ISDN and non-ISDN (PSTN) over the
national or international ISUP between networks. The TSS&TP specification covers the procedures described in
ITU-T Recommendation H.323 [3] , ITU-T Recommendation H.225.0 [4] as specified in TS 101 883 [1] and
ITU-T Recommendation Q.931 [5]".
All test purposes are written with reference to ITU-T Recommendation H.246 annex C [10] which implies the following
test architecture:
SUT
H.323 ISmapping UP mapping ISDN
H.323
ISDN
H.323->ISUP ISUP->ISDN
terminal
terminal
H.246
annex C (Q.699)
H.323-ISDN inter-working testing architecture via ISUP
Two mapping functions are involved. They are specified in ITU-T Recommendation H.246 annex C [10]
(H.323-ISUP) and ITU-T Recommendation Q.699 [23] (ISDN-ISUP).
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
[1] ETSI TS 101 883: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Mapping; Implementation of TIPHON architecture using
H.323".
[2] Void.
[3] ITU-T Recommendation H.323 (2000): "Packet-based multimedia communication".
[4] ITU-T Recommendation H.225.0 (2000): "Call signalling protocols and media stream
packetization for packet-based multimedia communication systems".
[5] ITU-T Recommendation Q.931: "ISDN user-network interface layer 3 specification for basic call
control".
ETSI
7 ETSI TS 102 169-1 V1.1.1 (2003-02)
[6] ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 1: General concepts".
[7] ISO/IEC 9646-2: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 2: Abstract Test Suite specification".
[8] ISO/IEC 9646-3: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)".
[9] ITU-T Recommendation H.245 (2001): "Control protocol for multimedia communication.
[10] ITU-T Recommendation H.246 annex C (2000): "ISDN User Part Function - H.225.0
Interworking".
[11] ETSI EN 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber Signalling
System No. one (DSS1) protocol; Signalling network layer for circuit-mode basic call control;
Part 1: Protocol specification [ITU-T Recommendation Q.931 (1993), modified]".
[12] Void.
[13] ETSI TBR 008: "Integrated Services Digital Network (ISDN); Telephony 3,1 kHz teleservice;
Attachment requirements for handset terminals".
[14] ETSI EG 201 018: "Integrated Services Digital Network (ISDN);Application of the Bearer
Capability (BC), High Layer Compatibility (HLC) and Low Layer Compatibility (LLC)
information elements by terminals supporting ISDN services".
[15] ETSI ETS 300 092-1: "Integrated Services Digital Network (ISDN); Calling Line Identification
Presentation (CLIP) supplementary service; Digital Subscriber Signalling System No. one (DSS1)
protocol; Part 1: Protocol specification".
[16] ETSI ETS 300 093-1: "Integrated Services Digital Network (ISDN); Calling Line Identification
Restriction (CLIR) supplementary service; Digital Subscriber Signalling System No. one (DSS1)
protocol; Part 1: Protocol specification".
[17] ETSI ETS 300 097-1: "Integrated Services Digital Network (ISDN); Connected Line Identification
Presentation (COLP) supplementary service; Digital Subscriber Signalling System No. one
(DSS1) protocol; Part 1: Protocol specification".
[18] ETSI ETS 300 098-1: "Integrated Services Digital Network (ISDN); Connected Line Identification
Restriction (COLR) supplementary service; Digital Subscriber Signalling System No. one (DSS1)
protocol; Part 1: Protocol specification".
[19] ETSI ETS 300 267-1: "Integrated Services Digital Network (ISDN); Telephony 7 kHz and
videotelephony teleservices; Digital Subscriber Signalling System No. one (DSS1) protocol;
Part 1: Protocol specification".
[20] ETSI ETR 018: "Integrated Services Digital Network (ISDN); Application of the Bearer
Capability (BC), High Layer Compatibility (HLC) and Low Layer Compatibility (LLC)
information elements by terminals supporting ISDN services".
[21] ETSI ETS 300 092-1/Amendment 2: "Integrated Services Digital Network (ISDN); Calling Line
Identification Presentation (CLIP) supplementary service; Digital Subscriber Signalling System
No. one (DSS1) protocol; Part 1: Protocol specification".
[22] ETSI ETS 300 097-1/Amendment 1: "Integrated Services Digital Network (ISDN); Connected
Line Identification Presentation (COLP) supplementary service; Digital Subscriber Signalling
System No. one (DSS1) protocol; Part 1: Protocol specification".
[23] ITU-T Recommendation Q.699: "Interworking between ISDN access and non-ISDN access over
ISDN User Part of Signalling System No. 7".
ETSI
8 ETSI TS 102 169-1 V1.1.1 (2003-02)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
• terms defined in ITU-T Recommendation H.323 [3];
• terms defined in ITU-T Recommendation H.225.0 [4];
• terms defined in ISO/IEC 9646 parts 1 [6] to 3 [8].
Basic Call Control (BCC): signalling protocol associated with the DSS1 - ISDN Basic Call control procedures of
ITU-T Recommendation Q.931 (EN 300 403-1)
inopportune: specifies a test purpose covering a signalling procedure where an inopportune message (type of message
not expected in the IUT current state) is sent to the IUT
syntactically invalid: specifies a test purpose covering a signalling procedure where a valid (expected in the current
status of the IUT) but not correctly encoded (unknown or incorrect parameter values) message is sent to the IUT, which
shall react correctly and eventually reject the message
test purpose: non-formal test description, mainly using text. This test description can be used as the basis for a formal
test specification (e.g. Abstract Test Suite in TTCN). See ISO/IEC 9646.
valid: specifies a test purpose covering a signalling procedure where all the messages sent to or received from the IUT
are valid (expected in the current status of the IUT) and correctly encoded
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
I Inopportune
IPTN IP Transmit Network
IUT Implementation Under Test
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
S Syntactically invalid
SCN Switched Circuit Network
TP Test Purpose
TSS Test Suite Structure
V Valid
ETSI
SCN plane
9 ETSI TS 102 169-1 V1.1.1 (2003-02)
4 Architecture and Test Suite Structure (TSS)
4.1 Architecture
Figure 1 shows the different types of networks that may inter-operate for calls. A specific call may not involve all
network types. Each network will include any required interconnecting and interworking functions.
Home
IPTN
Originating Intermediate Terminating
IPTN IPTN IPTN
Originating Intermediate Terminating
SCN SCN SCN
Figure 1: Network architecture
Management plane
Accounting Accounting
A A
S5 S5
Network FG Gateway FG
Terminal FG
User
User-Service
CR
QoSP CR QoSP
Profile Profile
Note
S1 S2 S3 S4
S1 S2 S4 S3
R2 R2
R1 SC2’
SC SC SC SC
TREG SREG IREG HREG
SC1
SC2
C2
C3
C1 SC2
CC CC CC
C2
C1 C3
BC
BC BC
N1
N3
N2
M2
M1 M3
MC MC MC
T1 T2
T2
TRM TRM TRM
Figure 2: General reference configuration
ETSI
IP Transport Plane
Service
Service
control
Media Call control
Bearer
10 ETSI TS 102 169-1 V1.1.1 (2003-02)
4.2 Test Suite Structure (TSS)
4.2.1 ISDN-H.323
C - Plane /U - Plane
Basic_Call Successful Speech IH___ SP __ xx
3,1 kHz audio IH___ AU __ xx
UDI IH___ UD __ xx
C - Plane Unsuccessful IH____xx___Uxx
Supplementary
Services CLIP IH___xxSSCLIP xx
CLIR IH___xxSSCLIR xx
COLP IH___xxSSCOLP xx
COLR IH___xxSSCOLR xx
4.2.2 H.323-ISDN
C - Plane /U - Plane
Basic_Call Successful Speech HI___ SP ___xx
3,1 kHz audio HI___ AU ___xx
UDI HI___ UD __ _xx
C - Plane Unsuccessful HI___ xx __ Uxx
Supplementary
Services CLIP HI___xxSSCLIP xx
CLIR HI___xxSSCLIR xx
COLP HI___xxSSCOLP xx
COLR HI___xxSSCOLR xx
ETSI
11 ETSI TS 102 169-1 V1.1.1 (2003-02)
4.2.3 PSTN-H.323
C - Plane /U - Plane
Basic_Call Successful PH___ AU __ xx
Unsuccessful PH___ AU __Uxx
4.2.4 H.323-PSTN
C - Plane /U - Plane
Basic_Call Successful Speech HP___ SP __ xx
3,1 kHz audio HP___ AU __ xx
Unsuccessful HP___ xx __U xx
4.2.5 H.323-H.323 (PC-PC)
C - Plane /U - Plane
Basic_Call Successful HH___xx __ xx
Unsuccessful HH___xx __ Uxx
ETSI
12 ETSI TS 102 169-1 V1.1.1 (2003-02)
5 Numbering Scheme
Pos. 1: Network of the A-Subscriber
Pos. 2: Network of the B-Subscriber
Pos. 3: Network of the C-Subscriber
Pos. 4: Network of the D-Subscriber
Pos. 5: Network of the E-Subscriber
The following Network Codes apply:
_: No such network used (used e.g. for C-Subscriber in successful A to B Calls)
(underscore makes it easier to read the name)
P: PSTN
I: ISDN
H: H.323
(Extensions will be added when needed)
Pos. 6 and 7: Bearer- or Teleservice involved
xx: defined per PIXIT value
NOTE: This may be appropriate for Test Purposes (provided the Test Purpose states for which Bearer- and/or
Tele Services it should be tested). It is however NOT appropriate for Test Cases since it would be
detrimental to Test Automation
SP: Speech
AU: 3,1 kHz Audio
UD: UDI
UT: UDI/TA
Pos. 8 and 9:
__: No Supplementary Services Involved /Successful
_U: No Supplementary Services Involved /Unsuccessful
SS: Supplementary Services Involved
SI: Supplementary Services interaction
SN: Nonsymmetrical Supplementary Services Involved
ST: Supplementary Services transparent
Speech IH___SP__xx
1 2 3 4 5 6 7 8 9 10 11
I H _ _ _ S P _ _ x x
ETSI
13 ETSI TS 102 169-1 V1.1.1 (2003-02)
Supplementary Services
CLIP IH___xxSSCLIP xx
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
I H _ _ _ X X S S C L I P x x
6 Test purposes
6.1 Test purposes for ISDN-H.323 Basic call Successful -
Speech
Successful
Speech
IH___SP__01 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.2
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose:
Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CALL PROCEEDING message including the fastStart
field, call establishment continues.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
IH___SP__02 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference:
ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of an ALERTING message including the fastStart field, call
establishment continues.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter
BC=speech, no HLC
values:
Comments:
ETSI
14 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___SP__03 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.3
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose:
Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the fastStart field, call
establishment continues.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
IH___SP__04 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.2
H.246 annex C [10] § C.7.1
TSS reference:
ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CALL PROCEEDING message including the Fast
Connect Refused field, call establishment continues. The H.245 [9] master slave
determination should be started.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter
BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
IH___SP__05 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] Release 3 § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of an ALERTING message including the Fast Connect
Refused field, call establishment continues. The H.245 [9] master slave determination
should be started.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
ETSI
15 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___SP__06 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.3
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose:
Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the Fast Connect
Refused field, call establishment continues. The H.245 [9] master slave determination
should be started.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter
BC=speech, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
IH___SP__07 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.2 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose: Ensure that call establishment using overlap sending is performed correctly
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the fastStart field, call
establishment continues.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter
BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
IH___SP__08 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.2 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.3
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria:
Test purpose: Ensure that call establishment using overlap sending is performed correctly
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the Fast Connect
Refused field, call establishment continues. The H.245 [9] master slave determination
should be started.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
ETSI
16 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___SP__09 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.3.3 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.7
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech/
Selection criteria:
Test purpose:
Ensure that the call establishment and the call clearing procedure is performed correctly
when the calling user clears after answering with a DISCONNECT message indicating
the cause value # 16 "normal call clearing".
The called user shall receive a RELEASE COMPLETE message indicating the cause
value # 16 "normal call clearing" or ReleaseCompleteReason facilityCallDeflection.
Ensure that in the Call Delivered call state U4 the transfer of tone or announcement on
the B- channel is performed correctly.
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
IH___SP__10 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.3.3 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech/
Selection criteria:
Test purpose:
Ensure that the call clearing procedure is performed correctly when the called user
clears after answering with a RELEASE COMPLETE message indicating the cause
value # 16 "normal call clearing".
The calling user shall receive a DISCONNECT message with the cause value # 16
"normal call clearing".
Ensure that in the Call Delivered call state U4 and disconnect indication state (N12) the
transfer of tone or announcement on the B- channel is performed correctly.
parameters). The fastStart element indicates the CODEC value in a H.245 [9]
OpenLogicalChannel structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
IH___SP__11 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.3.3 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/Speech/
Selection criteria:
Test purpose:
Ensure that the call clearing procedure is performed correctly when the called user
clears after answering with a RELEASE COMPLETE message indicating the
ReleaseCompleteReason facilityCallDeflection.
The calling user shall receive a DISCONNECT message with the cause value # 16
"normal call clearing".
Ensure that in the Call Delivered call state U4 and disconnect indication state (N12) the
transfer of tone or announcement on the B- channel is performed correctly.
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=speech, no HLC
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
ETSI
17 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___SP__12 ISDN ref. to: PBN ref. to:
Q.931 [5], § 4.5.16 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8
TBR 008 [13] § 5.1.3, H.246 annex C [10] § C.7.1
EG 201 018 [14], § 6.3.1
TSS reference:
ISDN-H.323 [3]/Basic_call/Successful/Speech
Selection criteria: Telephony 3,1 kHz teleservice
Test purpose: Ensure that call establishment supporting the telephony 3,1 kHz teleservice is performed
correctly.
Ensure that in the active call state (N10) the voice transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters). The fastStart element indicates the
CODEC value in a H.245 [9] OpenLogicalChannel structure.
ISDN Parameter BC=speech, HLC=telephony
values:
H.323 [3] Parameter BC=speech, no HLC
values:
Comments:
Values for test purposes IH___SP__01 to IH___SP__12
VA_01 g711Alaw64k
VA_02 g711Alaw56k
VA_03 g711Ulaw64k
VA_04 g711Ulaw56k
VA_05 g722-64k
VA_06 g722-56k
VA_07 g722-48k
VA_08 g7231
VA_09 g728
VA_10 g729
VA_11 g729annexA
VA_12 is11172AudioCapability
VA_13 is13818AudioCapability
VA_14 g729wannexB
VA_15 g7231annexCCapability
VA_16 gsmFullRate GSMAudioCapability
VA_17 gsmHalfRate GSMAudioCapability
VA_18 gsmEnhancedFullRate GSMAudioCapability
VA_19 genericAudioCapability GenericCapability
ITU-T Recommendation H.245 [9] - G-series audio codepoints
Mapping of ASN.1 Codepoints to the Semantic meaning of codepoint
ASN.1 Codepoint Semantic meaning of codepoint
g711Alaw64k G.711 audio at 64 kbit/s, A-law
g711Alaw56k G.711 audio at 56 kbit/s, A-law, truncated to 7 bits
g711Ulaw64k G.711 audio at 64 kbit/s, μ-law
g711Ulaw56k
G.711 audio at 56 kbit/s, μ-law, truncated to 7 bits
g722-64k G.722 7 kHz audio at 64 kbit/s
g722-56k G.722 7 kHz audio at 56 kbit/s
g722-48k G.722 7 kHz audio at 48 kbit/s
g7231 G.723.1 at either 5,3 kbit/s or 6,3 kbit/s
g728 G.728 audio at 16 kbit/s
g729 G.729 audio at 8 kbit/s
ASN.1 Codepoint Semantic meaning of codepoint
g729annexA G.729 annex A audio at 8 kbit/s
g729wannexB G.729 audio at 8 kbit/s with silence suppression as in annex B
g729annexAwannexB G.729 annex A audio at 8 kbit/s with silence suppression as in annex B
g7231annexCCapability G.723.1 with annex C
gsmFullRate Full-rate speech transcoding (GSM 06.10)
gsmHalfRate Half-rate speech transcoding (GSM 06.20)
gsmEnhancedFullRate Enhanced Full Rate (EFR) speech transcoding (GSM 06.60)
ETSI
18 ETSI TS 102 169-1 V1.1.1 (2003-02)
6.2 Test purposes for ISDN-H.323 Basic call Successful -
3,1 kHz audio
Successful
3,1 kHz audio
IH___AU__01 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.2
H.246 [10] annex C§ C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CALL PROCEEDING message including the fastStart
field, call establishment continues.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter
BC=3,1 kHz audio, no HLC
values:
H.323 [3] Parameter
BC=3,1 kHz audio, no HLC
values:
Comments:
IH___AU__02 ISDN ref. to: PBN ref. to:
Q.931 [5] § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a ALERTING message including the fastStart field, call
establishment continues.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=3,1 kHz audio, no HLC
values:
H.323 [3] Parameter BC=3,1 kHz audio, no HLC
values:
Comments:
ETSI
19 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___AU__03 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.3
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose:
Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the fastStart field, call
establishment continues.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=3,1 kHz audio, no HLC
values:
H.323 [3] Parameter BC=3,1 kHz audio, no HLC
values:
Comments:
IH___AU__04 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.2
H.246 annex C [10] § C.7.1
TSS reference:
ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CALL PROCEEDING message including the Fast
Connect Refused field, call establishment continues. The H.245 [9] master slave
determination should be started.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter
BC=3,1 kHz audio, no HLC
values:
H.323 [3] Parameter BC=3,1 kHz audio, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
IH___AU__05 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose: Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a ALERTINGmessage including the Fast Connect
Refused field, call establishment continues. The H.245 [9] master slave determination
should be started.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter BC=3,1 kHz audio, no HLC
values:
H.323 [3] Parameter BC=3,1 kHz audio, no HLC
values:
Comments: This test is not necessary in a TIPHON compliant SUT.
ETSI
20 ETSI TS 102 169-1 V1.1.1 (2003-02)
IH___AU__06 ISDN ref. to: PBN ref. to:
Q.931 [5], § 5.1.5.1 H.225.0 [4] § 7.2.2.1, § 7.3.10, § 7.3.2
Q.699 [23], § 2.1.1 TS 101 883 [1] § 5.1, § B.1.3.8, § B.1.3.1
H.246 annex C [10] § C.7.1
TSS reference: ISDN-H.323 [3]/Basic_call/Successful/3,1 kHz audio
Selection criteria:
Test purpose:
Ensure that call establishment using en-bloc sending is performed correctly.
Ensure that the SETUP message on the H.323 [3] interface is sent including the
fastStart field and on receipt of a CONNECT message including the Fast Connect
Refused field, call establishment continues. The H.245 [9] master slave determination
should be started.
Ensure that in the active call state (N10) the data transfer on the media and B-channels
is performed correctly (e.g. testing QoS parameters).
The fastStart element indicates the CODEC value in a H.245 [9] OpenLogicalChannel
structure.
ISDN Parameter B
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...