ETSI EN 301 908-1 V7.1.1 (2015-03)
IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements
IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements
REN/MSG-TFES-011-01
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 1. del: Uvod in splošne zahteve
Ta dokument se uporablja za uporabniško opremo, ponavljalnike in bazne postaje za sisteme IMT, ki spadajo pod področje uporabe enega od drugih delov standarda ETSI EN 301 908 [i.11], razen za IMT-2000 FDMA/TDMA (digitalna izboljšana brezvrvična komunikacija (DECT)). Ta dokument zajema tudi ustrezno pomožno opremo.
OPOMBA 1: ETSI EN 301 908-10 [i.10] vsebuje predvsem zahteve za izsevane lažne emisije ter obvladovanje in nadzorovanje funkcij opreme IMT-2000 FDMA/TDMA (digitalna izboljšana brezvrvična komunikacija). Ta dokument zajema tehnične zahteve, pogoste pri opremi, ki spada v področje uporabe nekaterih drugih delov.
OPOMBA 2: Drugi deli ETSI EN 301 908 [i.11], navedeni v predgovoru tega dokumenta, določajo tehnične zahteve v zvezi s posebnim tipom opreme IMT.
OPOMBA 3: Priporočili ITU-R M.1457-11 [i.7] in M.2012 [i.8] določata karakteristike članov družine IMT-2000 in IMT-Advanced s tehničnimi specifikacijami, ki so jih razvile organizacije za pripravo standardov. Ta dokument velja za opremo, ki ustreza vsem različicam prizemnih specifikacij, navedenih v priporočilih ITU-R M.1457-11 [i.7] in M.2012 [i.8].
Ta dokument zajema določbe člena 3(2) Direktive 1999/5/ES [i.2] (direktive R&TTE), ki določa, da »[...] mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.2].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks;Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive;Part 1: Introduction and common requirements33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-1 V7.1.1SIST EN 301 908-1 V7.1.1:2015en,fr,de01-oktober-2015SIST EN 301 908-1 V7.1.1:2015SLOVENSKI
STANDARD
SIST EN 301 908-1 V7.1.1:2015
ETSI EN 301 908-1 V7.1.1 (2015-03) IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements
HARMONIZED EUROPEAN STANDARD SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 2
Reference REN/MSG-TFES-011-01 Keywords 3G, 3GPP, 3GPP2, cdma2000, cellular, digital, E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE, LTE-Advanced, MAN-Advanced, mobile, radio, regulation, UMTS, UTRA, WCDMA, WiMAX ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Modal verbs terminology . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions, symbols and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 9 3.3 Abbreviations . 10 4 Technical requirements specifications . 10 4.1 Environmental profile . 10 4.2 Conformance requirements . 11 4.2.1 Introduction. 11 4.2.2 Radiated emissions (UE) . 11 4.2.2.1 Definition . 11 4.2.2.2 Limits . 11 4.2.2.3 Conformance . 12 4.2.3 Radiated emissions (BS and repeater) . 12 4.2.3.1 Definition . 12 4.2.3.2 Limits . 12 4.2.3.3 Conformance . 13 4.2.4 Control and monitoring functions (UE) . 13 4.2.4.1 Definition . 13 4.2.4.2 Limits . 13 4.2.4.3 Conformance . 13 5 Testing for compliance with technical requirements . 13 5.1 Environmental conditions for testing . 13 5.2 Interpretation of the measurement results . 14 5.3 Essential radio test suites . 14 5.3.1 Radiated emissions (UE) . 14 5.3.1.1 Test method . 14 5.3.1.2 Test configurations . 15 5.3.2 Radiated emissions (BS and repeater) . 15 5.3.2.1 Test method . 15 5.3.2.2 Test configurations . 16 5.3.3 Control and monitoring functions (UE) . 17 5.3.3.1 Test method . 17 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 18 Annex B (informative): Receiver sensitivity and correct operation of the equipment . 20 B.1 Receiver sensitivity . 20 B.2 Correct functioning of the equipment. 20 Annex C (informative): Overview and organization of ETSI EN 301 908 standard parts . 21 Annex D: Void . 25 Annex E (informative): Bibliography . 26 History . 27
SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A. The present document is part 1 of a multi-part deliverable covering the essential requirements under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT cellular networks, as identified below: Part 1: "Introduction and common requirements"; Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)"; Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)"; Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)"; Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)"; Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)"; Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)"; Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)"; Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA FDD) (Repeaters)"; SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 5 Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 18: "E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)"; Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)"; Part 20: "OFDMA TDD WMAN (Mobile WiMAX) TDD Base Station (BS)"; Part 21: "OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)"; Part 22: "OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates Date of adoption of this EN: 10 March 2015 Date of latest announcement of this EN (doa): 30 June 2015 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2015 Date of withdrawal of any conflicting National Standard (dow): 31 December 2016
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in ETSI EG 201 399 [i.3]. SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 6 1 Scope The present document applies to user equipment, repeaters and base stations for IMT, falling within the scope of one of the other parts of ETSI EN 301 908 [i.11], except for IMT-2000 FDMA/TDMA (DECT). The present document also covers the corresponding ancillary equipment.
NOTE 1: ETSI EN 301 908-10 [i.10] contains in particular requirements for radiated spurious emissions and control and monitoring functions applicable to IMT-2000 FDMA/TDMA (DECT) equipment. The present document includes technical requirements which are common to equipment falling within the scope of several of the other parts. NOTE 2: The other parts of ETSI EN 301 908 [i.11], which are listed in the foreword of the present document, specify technical requirements in respect of a particular type of IMT equipment. NOTE 3: Recommendations ITU-R M.1457-11 [i.7] and M.2012 [i.8] define the characteristics of the members of the IMT-2000 family and IMT-Advanced respectively by means of references to technical specifications developed by Standards Development organizations. The present document applies to equipment designed to meet any version of the terrestrial specifications referenced in Recommendations ITU-R M.1457-11 [i.7] and M.2012 [i.8]. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference." In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain". [2] ETSI EN 301 502 (V11.1.1) (07-2014): "Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 7 The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] Void. [i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.6] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. [i.7] Recommendation ITU-R M.1457-11 (2013): "Detailed specifications of the terrestrial radio interfaces of International Mobile Telecommunications-2000 (IMT-2000)". [i.8] Recommendation ITU-R M.2012 (2012): "Detailed specifications of the terrestrial radio interfaces of International Mobile Telecommunications-Advanced (IMT-Advanced)". [i.9] Recommendation ITU-R SM.1539-1 (2002): "Variation of the boundary between the out-of-band and spurious domains required for the application of Recommendations ITU-R SM.1541 and ITU-R SM.329". [i.10] ETSI EN 301 908-10 (V4.1.1) (07-2009): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive". [i.11] ETSI EN 301 908 (all parts): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R&TTE Directive [i.2] and the following apply: ancillary equipment: equipment (apparatus), used in connection with a User Equipment (UE), Repeater or Base Station (BS) is considered as an ancillary equipment (apparatus) if: • the equipment is intended for use in conjunction with a user equipment UE, repeater or BS to provide additional operational and/or control features to the radio equipment, (e.g. to extend control to another position or location); and • the equipment cannot be used on a stand-alone basis to provide user functions independently of a UE, BS or combination of BS and repeater; and • the UE, BS or combination of BS and repeater to which it is connected, is capable of providing some intended operation, such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a sub-unit of the main equipment essential to the main equipment basic functions). applicable part: part of the multi-part deliverable, of which the present document is the first part, for which the scope of that document includes the equipment to be tested SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 8 Base Station RF bandwidth: bandwidth in which a Base Station transmits and receives multiple carriers and/or RATs simultaneously channel bandwidth: RF bandwidth supporting a single E-UTRA, Mobile WiMAX or UMB RF carrier with the transmission bandwidth configured in the uplink or downlink of a cell NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF requirements. enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port. environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the present document idle mode: state of User Equipment (UE) when switched on but with no Radio Resource Control (RRC) connection IMT-2000: mobile systems as defined in Recommendation ITU-R M.1457-11 [i.7] NOTE: Recommendation ITU-R M.1457-11 [i.7] identifies the detailed specifications for the IMT-2000 radio interfaces. IMT-Advanced: mobile systems as defined in Recommendation ITU-R M.2012 [i.8] NOTE: Recommendation ITU-R M.2012 [i.8] identifies the detailed specifications for the IMT-Advanced radio interfaces. Lower RF bandwidth edge: frequency of the lower edge of the Base Station RF bandwidth, used as a frequency reference point for transmitter and receiver requirements MSR Base Station: Base Station characterized by the ability of its receiver and transmitter to process two or more carriers in common active RF components simultaneously in a declared RF bandwidth, where at least one carrier is of a different RAT than the other carrier(s) multi-band Base Station: Base Station characterized by the ability of its transmitter and/or receiver to process two or more carriers in common active RF components simultaneously, where at least one carrier is configured at a different non-overlapping operating band than the other carrier(s) port: particular interface, of the specified equipment (apparatus), with the electromagnetic environment NOTE: For example, any connection point on an equipment intended for connection of cables to or from that equipment is considered as a port (see figure 3.1-1).
Figure 3.1-1: Examples of ports
Enclosure port
Apparatus
DC Power port
AC Power port
Earth port Antenna port
Signal/Control port
Telecommunications port
SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 9
Figure 3.1-2: BS with single enclosure solution
Figure 3.1-3: BS with multiple enclosure solution radio communications equipment: telecommunications equipment which includes one or more transmitters and/or receivers and/or parts thereof for use in a fixed, mobile or portable application NOTE: It can be operated with ancillary equipment but if so, is not dependent on it for basic functionality. radio digital unit: equipment which contains base band and functionality for controlling Radio unit radio equipment: equipment which contains Radio digital unit and Radio unit radio unit: equipment which contains transmitter and receiver signal and control port: port which carries information or control signals, excluding antenna ports telecommunication port: port which is intended to be connected to telecommunication networks (e.g. public switched telecommunication networks, integrated services digital networks), local area networks (e.g. Ethernet, token ring) and similar networks traffic mode: state of User Equipment (UE) when switched on and with Radio Resource Control (RRC) connection established Upper RF bandwidth edge: frequency of the upper edge of the Base Station RF bandwidth, used as a frequency reference point for transmitter and receiver requirements WiMAX: trade marked name for the OFDMA TDD WMAN IMT technology 3.2 Symbols For the purposes of the present document, the following symbols apply: BWChannel Channel bandwidth FBW RF, high Upper RF bandwidth edge FBW RF, low Lower RF bandwidth edge Radio Equipment BS Equipment Radio digital unit Radio Equipment Radio unit BS Equipment SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 10 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BS Base Station CDMA Code Division Multiple Access CW Continuous Wave DECT Digital Enhanced Cordless Telecommunication e.i.r.p. equivalent isotropically radiated power e.r.p. effective radiated power EDGE Enhanced Data rates for GSM Evolution EMC ElectroMagnetic Compatibility ERM Electromagnetic compatibility and Radio spectrum Matters EUT Equipment Under Test E-UTRA Evolved Universal Terrestrial Radio Access NOTE: Also known as LTE. FDD Frequency Division Duplex FDMA Frequency Division Multiple Access GSM Global System for Mobile communications IMT International Mobile Telecommunications NOTE: Includes both IMT-2000 and IMT-Advanced RITs. ITU-R International Telecommunication Union Radio sector LTE Long Term Evolution NOTE: Also known as E-UTRA. MSG Mobile Standards Group MSR Multi-Standard Radio OFDMA Orthogonal Frequency Division Multiple Access R&TTE Radio Telecommunications and Terminal Equipment RAT Radio Access Technology RF Radio Frequency RIT Radio Interface Technology RMS Root Mean Square RRC Radio Resource Control SDO Standard Development Organization TDD Time Division Duplex TDMA Time Division Multiple Access TFES Task Force for European Standards for IMT TIA Telecommunications Industry Association UE User Equipment UMB Ultra Mobile Broadband UTRA Universal Terrestrial Radio Access UWC Universal Wireless Communications WMAN Wireless Metropolitan Area Network 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. SIST EN 301 908-1 V7.1.1:2015
ETSI ETSI EN 301 908-1 V7.1.1 (2015-03) 11 4.2 Conformance requirements The requirements in the present document are based on the assumption that the operating band is shared between systems of the IMT family or systems having compatible characteristics. For BS capable of multi-band operation, the requirements in the present document apply for each supported operating band unless otherwise stated. For emission tests, all operating bands shall be activated according to the applicable test configuration. 4.2.1 Introduction To meet the essential requirement under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for IMT equipment three common essential parameters have been identified. Tables 4.2.1-1 and 4.2.1-2 provide cross-references, for UE, repeater and BS respectively, between these essential parameters and the corresponding technical requirements for equipment within the scope of the present document. Table 4.2.1-1: Cross references for User Equipment (UE) Essential parameter Corresponding technical requirements Radiated emissions 4.2.2 Radiated emissions (UE) Control and monitoring functions 4.2.4 Control and monitoring functions (UE)
Table 4.2.1-2: Cross references for Base Stations (BS), and repeaters Essential parameter Correspond
...
ETSI EN 301 908-1 V7.1.1 (2015-03)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 1: Introduction and common requirements
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-1 V7.1.1 (2015-03)
Reference
REN/MSG-TFES-011-01
Keywords
3G, 3GPP, 3GPP2, cdma2000, cellular, digital,
E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE,
LTE-Advanced, MAN-Advanced, mobile, radio,
regulation, UMTS, UTRA, WCDMA, WiMAX
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-1 V7.1.1 (2015-03)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Radiated emissions (UE) . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 12
4.2.3 Radiated emissions (BS and repeater) . 12
4.2.3.1 Definition . 12
4.2.3.2 Limits . 12
4.2.3.3 Conformance . 13
4.2.4 Control and monitoring functions (UE) . 13
4.2.4.1 Definition . 13
4.2.4.2 Limits . 13
4.2.4.3 Conformance . 13
5 Testing for compliance with technical requirements . 13
5.1 Environmental conditions for testing . 13
5.2 Interpretation of the measurement results . 14
5.3 Essential radio test suites . 14
5.3.1 Radiated emissions (UE) . 14
5.3.1.1 Test method . 14
5.3.1.2 Test configurations . 15
5.3.2 Radiated emissions (BS and repeater) . 15
5.3.2.1 Test method . 15
5.3.2.2 Test configurations . 16
5.3.3 Control and monitoring functions (UE) . 17
5.3.3.1 Test method . 17
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 18
Annex B (informative): Receiver sensitivity and correct operation of the equipment . 20
B.1 Receiver sensitivity . 20
B.2 Correct functioning of the equipment. 20
Annex C (informative): Overview and organization of ETSI EN 301 908 standard parts . 21
Annex D: Void . 25
Annex E (informative): Bibliography . 26
History . 27
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-1 V7.1.1 (2015-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 1 of a multi-part deliverable covering the essential requirements under article 3.2 of
Directive 1999/5/EC [i.2] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT
cellular networks, as identified below:
Part 1: "Introduction and common requirements";
Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)";
Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)";
Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)";
Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)";
Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)";
Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)";
Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)";
Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA FDD) (Repeaters)";
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-1 V7.1.1 (2015-03)
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 18: "E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)";
Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)";
Part 20: "OFDMA TDD WMAN (Mobile WiMAX) TDD Base Station (BS)";
Part 21: "OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)";
Part 22: "OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates
Date of adoption of this EN: 10 March 2015
Date of latest announcement of this EN (doa): 30 June 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2015
Date of withdrawal of any conflicting National Standard (dow): 31 December 2016
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-1 V7.1.1 (2015-03)
1 Scope
The present document applies to user equipment, repeaters and base stations for IMT, falling within the scope of one of
the other parts of ETSI EN 301 908 [i.11], except for IMT-2000 FDMA/TDMA (DECT). The present document also
covers the corresponding ancillary equipment.
NOTE 1: ETSI EN 301 908-10 [i.10] contains in particular requirements for radiated spurious emissions and
control and monitoring functions applicable to IMT-2000 FDMA/TDMA (DECT) equipment.
The present document includes technical requirements which are common to equipment falling within the scope of
several of the other parts.
NOTE 2: The other parts of ETSI EN 301 908 [i.11], which are listed in the foreword of the present document,
specify technical requirements in respect of a particular type of IMT equipment.
NOTE 3: Recommendations ITU-R M.1457-11 [i.7] and M.2012 [i.8] define the characteristics of the members of
the IMT-2000 family and IMT-Advanced respectively by means of references to technical specifications
developed by Standards Development organizations. The present document applies to equipment
designed to meet any version of the terrestrial specifications referenced in Recommendations ITU-R
M.1457-11 [i.7] and M.2012 [i.8].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference."
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain".
[2] ETSI EN 301 502 (V11.1.1) (07-2014): "Global System for Mobile communications (GSM);
Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of
the R&TTE Directive".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-1 V7.1.1 (2015-03)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the R&TTE Directive".
[i.4] Void.
[i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.6] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
[i.7] Recommendation ITU-R M.1457-11 (2013): "Detailed specifications of the terrestrial radio
interfaces of International Mobile Telecommunications-2000 (IMT-2000)".
[i.8] Recommendation ITU-R M.2012 (2012): "Detailed specifications of the terrestrial radio interfaces
of International Mobile Telecommunications-Advanced (IMT-Advanced)".
[i.9] Recommendation ITU-R SM.1539-1 (2002): "Variation of the boundary between the out-of-band
and spurious domains required for the application of Recommendations ITU-R SM.1541 and
ITU-R SM.329".
[i.10] ETSI EN 301 908-10 (V4.1.1) (07-2009): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT)
covering essential requirements of article 3.2 of the R&TTE Directive".
[i.11] ETSI EN 301 908 (all parts): "IMT cellular networks; Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [i.2] and the
following apply:
ancillary equipment: equipment (apparatus), used in connection with a User Equipment (UE), Repeater or Base
Station (BS) is considered as an ancillary equipment (apparatus) if:
• the equipment is intended for use in conjunction with a user equipment UE, repeater or BS to provide
additional operational and/or control features to the radio equipment, (e.g. to extend control to another position
or location); and
• the equipment cannot be used on a stand-alone basis to provide user functions independently of a UE, BS or
combination of BS and repeater; and
• the UE, BS or combination of BS and repeater to which it is connected, is capable of providing some intended
operation, such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a sub-unit of the
main equipment essential to the main equipment basic functions).
applicable part: part of the multi-part deliverable, of which the present document is the first part, for which the scope
of that document includes the equipment to be tested
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-1 V7.1.1 (2015-03)
Base Station RF bandwidth: bandwidth in which a Base Station transmits and receives multiple carriers and/or RATs
simultaneously
channel bandwidth: RF bandwidth supporting a single E-UTRA, Mobile WiMAX or UMB RF carrier with the
transmission bandwidth configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge
NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port.
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
idle mode: state of User Equipment (UE) when switched on but with no Radio Resource Control (RRC) connection
IMT-2000: mobile systems as defined in Recommendation ITU-R M.1457-11 [i.7]
NOTE: Recommendation ITU-R M.1457-11 [i.7] identifies the detailed specifications for the IMT-2000 radio
interfaces.
IMT-Advanced: mobile systems as defined in Recommendation ITU-R M.2012 [i.8]
NOTE: Recommendation ITU-R M.2012 [i.8] identifies the detailed specifications for the IMT-Advanced radio
interfaces.
Lower RF bandwidth edge: frequency of the lower edge of the Base Station RF bandwidth, used as a frequency
reference point for transmitter and receiver requirements
MSR Base Station: Base Station characterized by the ability of its receiver and transmitter to process two or more
carriers in common active RF components simultaneously in a declared RF bandwidth, where at least one carrier is of a
different RAT than the other carrier(s)
multi-band Base Station: Base Station characterized by the ability of its transmitter and/or receiver to process two or
more carriers in common active RF components simultaneously, where at least one carrier is configured at a different
non-overlapping operating band than the other carrier(s)
port: particular interface, of the specified equipment (apparatus), with the electromagnetic environment
NOTE: For example, any connection point on an equipment intended for connection of cables to or from that
equipment is considered as a port (see figure 3.1-1).
Enclosure port
AC Power port Antenna port
Signal/Control port
DC Power port
Apparatus
Telecommunications port
Earth port
Figure 3.1-1: Examples of ports
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-1 V7.1.1 (2015-03)
BS Equipment
Radio
Equipment
Figure 3.1-2: BS with single enclosure solution
BS Equipment
Radio Equipment
Radio
digital
Radio unit
unit
Figure 3.1-3: BS with multiple enclosure solution
radio communications equipment: telecommunications equipment which includes one or more transmitters and/or
receivers and/or parts thereof for use in a fixed, mobile or portable application
NOTE: It can be operated with ancillary equipment but if so, is not dependent on it for basic functionality.
radio digital unit: equipment which contains base band and functionality for controlling Radio unit
radio equipment: equipment which contains Radio digital unit and Radio unit
radio unit: equipment which contains transmitter and receiver
signal and control port: port which carries information or control signals, excluding antenna ports
telecommunication port: port which is intended to be connected to telecommunication networks (e.g. public switched
telecommunication networks, integrated services digital networks), local area networks (e.g. Ethernet, token ring) and
similar networks
traffic mode: state of User Equipment (UE) when switched on and with Radio Resource Control (RRC) connection
established
Upper RF bandwidth edge: frequency of the upper edge of the Base Station RF bandwidth, used as a frequency
reference point for transmitter and receiver requirements
WiMAX: trade marked name for the OFDMA TDD WMAN IMT technology
3.2 Symbols
For the purposes of the present document, the following symbols apply:
BW Channel bandwidth
Channel
F Upper RF bandwidth edge
BW RF, high
F Lower RF bandwidth edge
BW RF, low
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 301 908-1 V7.1.1 (2015-03)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
BS Base Station
CDMA Code Division Multiple Access
CW Continuous Wave
DECT Digital Enhanced Cordless Telecommunication
e.i.r.p. equivalent isotropically radiated power
e.r.p. effective radiated power
EDGE Enhanced Data rates for GSM Evolution
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio spectrum Matters
EUT Equipment Under Test
E-UTRA Evolved Universal Terrestrial Radio Access
NOTE: Also known as LTE.
FDD Frequency Division Duplex
FDMA Frequency Division Multiple Access
GSM Global System for Mobile communications
IMT International Mobile Telecommunications
NOTE: Includes both IMT-2000 and IMT-Advanced RITs.
ITU-R International Telecommunication Union Radio sector
LTE Long Term Evolution
NOTE: Also known as E-UTRA.
MSG Mobile Standards Group
MSR Multi-Standard Radio
OFDMA Orthogonal Frequency Division Multiple Access
R&TTE Radio Telecommunications and Terminal Equipment
RAT Radio Access Technology
RF Radio Frequency
RIT Radio Interface Technology
RMS Root Mean Square
RRC Radio Resource Control
SDO Standard Development Organization
TDD Time Division Duplex
TDMA Time Division Multiple Access
TFES Task Force for European Standards for IMT
TIA Telecommunications Industry Association
UE User Equipment
UMB Ultra Mobile Broadband
UTRA Universal Terrestrial Radio Access
UWC Universal Wireless Communications
WMAN Wireless Metropolitan Area Network
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of
the present document at all times when operating within the boundary limits of the declared operational environmental
profile.
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 301 908-1 V7.1.1 (2015-03)
4.2 Conformance requirements
The requirements in the present document are based on the assumption that the operating band is shared between
systems of the IMT family or systems having compatible characteristics.
For BS capable of multi-band operation, the requirements in the present document apply for each supported operating
band unless otherwise stated. For emission tests, all operating bands shall be activated according to the applicable test
configuration.
4.2.1 Introduction
To meet the essential requirement under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for IMT equipment
three common essential parameters have been identified. Tables 4.2.1-1 and 4.2.1-2 provide cross-references, for UE,
repeater and BS respectively, between these essential parameters and the corresponding technical requirements for
equipment within the scope of the present document.
Table 4.2.1-1: Cross references for User Equipment (UE)
Essential parameter Corresponding technical requirements
Radiated emissions 4.2.2 Radiated emissions (UE)
Control and monitoring functions 4.2.4 Control and monitoring functions (UE)
Table 4.2.1-2: Cross
...
Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 1: Introduction and common requirements
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
Reference
REN/MSG-TFES-011-01
Keywords
3G, 3GPP, 3GPP2, cdma2000, cellular, digital,
E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE,
LTE-Advanced, MAN-Advanced, mobile, radio,
regulation, UMTS, UTRA, WCDMA, WiMAX
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Radiated emissions (UE) . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 12
4.2.2.3 Conformance . 12
4.2.3 Radiated emissions (BS and repeater) . 12
4.2.3.1 Definition . 12
4.2.3.2 Limits . 12
4.2.3.3 Conformance . 13
4.2.4 Control and monitoring functions (UE) . 13
4.2.4.1 Definition . 13
4.2.4.2 Limits . 13
4.2.4.3 Conformance . 14
5 Testing for compliance with technical requirements . 14
5.1 Environmental conditions for testing . 14
5.2 Interpretation of the measurement results . 14
5.3 Essential radio test suites . 15
5.3.1 Radiated emissions (UE) . 15
5.3.1.1 Test method . 15
5.3.1.2 Test configurations . 15
5.3.2 Radiated emissions (BS and repeater) . 16
5.3.2.1 Test method . 16
5.3.2.2 Test configurations . 16
5.3.3 Control and monitoring functions (UE) . 17
5.3.3.1 Test method . 17
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 18
Annex B (informative): Receiver sensitivity and correct operation of the equipment . 20
B.1 Receiver sensitivity . 20
B.2 Correct functioning of the equipment. 20
Annex C (informative): Overview and organization of ETSI EN 301 908 standard parts . 21
Annex D (informative): Void . 25
Annex E (informative): Bibliography . 26
History . 27
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 1 of a multi-part deliverable covering the essential requirements under article 3.2 of
Directive 1999/5/EC [i.2] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT
cellular networks, as identified below:
Part 1: "Introduction and common requirements";
Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)";
Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)";
Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)";
Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)";
Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)";
Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)";
Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)";
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA FDD) (Repeaters)";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 18: "E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)";
Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)";
Part 20: "OFDMA TDD WMAN (Mobile WiMAX) TDD Base Station (BS)";
Part 21: "OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)";
Part 22: "OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
1 Scope
The present document applies to user equipment, repeaters and base stations for IMT, falling within the scope of one of
the other parts of ETSI EN 301 908 [i.11], except for IMT-2000 FDMA/TDMA (DECT). The present document also
covers the corresponding ancillary equipment.
NOTE 1: ETSI EN 301 908-10 [i.10] contains in particular requirements for radiated spurious emissions and
control and monitoring functions applicable to IMT-2000 FDMA/TDMA (DECT) equipment.
The present document includes technical requirements which are common to equipment falling within the scope of
several of the other parts.
NOTE 2: The other parts of ETSI EN 301 908 [i.11], which are listed in the foreword of the present document,
specify technical requirements in respect of a particular type of IMT equipment.
NOTE 3: Recommendations ITU-R M.1457-11 [i.7] and M.2012 [i.8] define the characteristics of the members of
the IMT-2000 family and IMT-Advanced respectively by means of references to technical specifications
developed by Standards Development organizations. The present document applies to equipment
designed to meet any version of the terrestrial specifications referenced in Recommendations ITU-R
M.1457-11 [i.7] and M.2012 [i.8].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference."
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain".
[2] ETSI EN 301 502 (V11.1.1) (07-2014): "Global System for Mobile communications (GSM);
Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of
the R&TTE Directive".
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the R&TTE Directive".
[i.4] Void.
[i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.6] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
[i.7] Recommendation ITU-R M.1457-11 (2013): "Detailed specifications of the terrestrial radio
interfaces of International Mobile Telecommunications-2000 (IMT-2000)".
[i.8] Recommendation ITU-R M.2012 (2012): "Detailed specifications of the terrestrial radio interfaces
of International Mobile Telecommunications-Advanced (IMT-Advanced)".
[i.9] Recommendation ITU-R SM.1539-1 (2002): "Variation of the boundary between the out-of-band
and spurious domains required for the application of Recommendations ITU-R SM.1541 and ITU-
R SM.329".
[i.10] ETSI EN 301 908-10 (V4.1.1) (07-2009): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT)
covering essential requirements of article 3.2 of the R&TTE Directive".
[i.11] ETSI EN 301 908 (all parts): "IMT cellular networks; Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [i.2] and the
following apply:
ancillary equipment: equipment (apparatus), used in connection with a User Equipment (UE), Repeater or Base
Station (BS) is considered as an ancillary equipment (apparatus) if:
• the equipment is intended for use in conjunction with a user equipment UE, repeater or BS to provide
additional operational and/or control features to the radio equipment, (e.g. to extend control to another position
or location); and
• the equipment cannot be used on a stand-alone basis to provide user functions independently of a UE, BS or
combination of BS and repeater; and
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
• the UE, BS or combination of BS and repeater to which it is connected, is capable of providing some intended
operation, such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a sub-unit of the
main equipment essential to the main equipment basic functions).
applicable part: part of the multi-part deliverable, of which the present document is the first part, for which the scope
of that document includes the equipment to be tested
Base Station RF bandwidth: bandwidth in which a Base Station transmits and receives multiple carriers and/or RATs
simultaneously
channel bandwidth: RF bandwidth supporting a single E-UTRA, Mobile WiMAX or UMB RF carrier with the
transmission bandwidth configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge
NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port.
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
idle mode: state of User Equipment (UE) when switched on but with no Radio Resource Control (RRC) connection
IMT-2000: mobile systems as defined in Recommendation ITU-R M.1457-11 [i.7]
NOTE: Recommendation ITU-R M.1457-11 [i.7] identifies the detailed specifications for the IMT-2000 radio
interfaces.
IMT-Advanced: mobile systems as defined in Recommendation ITU-R M.2012 [i.8]
NOTE: Recommendation ITU-R M.2012 [i.8] identifies the detailed specifications for the IMT-Advanced radio
interfaces.
Lower RF bandwidth edge: frequency of the lower edge of the Base Station RF bandwidth, used as a frequency
reference point for transmitter and receiver requirements
MSR Base Station: Base Station characterized by the ability of its receiver and transmitter to process two or more
carriers in common active RF components simultaneously in a declared RF bandwidth, where at least one carrier is of a
different RAT than the other carrier(s)
multi-band Base Station: Base Station characterized by the ability of its transmitter and/or receiver to process two or
more carriers in common active RF components simultaneously, where at least one carrier is configured at a different
non-overlapping operating band than the other carrier(s)
port: particular interface, of the specified equipment (apparatus), with the electromagnetic environment
NOTE: For example, any connection point on an equipment intended for connection of cables to or from that
equipment is considered as a port (see figure 3.1-1).
Enclosure port
AC Power port Antenna port
Signal/Control port
DC Power port
Apparatus
Telecommunications port
Earth port
Figure 3.1-1: Examples of ports
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
BS Equipment
Radio
Equipment
Figure 3.1-2: BS with single enclosure solution
BS Equipment
Radio Equipment
Radio
digital
Radio unit
unit
Figure 3.1-3: BS with multiple enclosure solution
radio communications equipment: telecommunications equipment which includes one or more transmitters and/or
receivers and/or parts thereof for use in a fixed, mobile or portable application
NOTE: It can be operated with ancillary equipment but if so, is not dependent on it for basic functionality.
radio digital unit: equipment which contains base band and functionality for controlling Radio unit
radio equipment: equipment which contains Radio digital unit and Radio unit
radio unit: equipment which contains transmitter and receiver
signal and control port: port which carries information or control signals, excluding antenna ports
telecommunication port: port which is intended to be connected to telecommunication networks (e.g. public switched
telecommunication networks, integrated services digital networks), local area networks (e.g. Ethernet, token ring) and
similar networks
traffic mode: state of User Equipment (UE) when switched on and with Radio Resource Control (RRC) connection
established
Upper RF bandwidth edge: frequency of the upper edge of the Base Station RF bandwidth, used as a frequency
reference point for transmitter and receiver requirements
WiMAX: trade marked name for the OFDMA TDD WMAN IMT technology
3.2 Symbols
For the purposes of the present document, the following symbols apply:
BW Channel bandwidth
Channel
F Upper RF bandwidth edge
BW RF, high
F Lower RF bandwidth edge
BW RF, low
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
BS Base Station
CDMA Code Division Multiple Access
CW Continuous Wave
DECT Digital Enhanced Cordless Telecommunication
e.i.r.p. equivalent isotropically radiated power
e.r.p. effective radiated power
EDGE Enhanced Data rates for GSM Evolution
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio spectrum Matters
EUT Equipment Under Test
E-UTRA Evolved Universal Terrestrial Radio Access
NOTE: Also known as LTE.
FDD Frequency Division Duplex
FDMA Frequency Division Multiple Access
GSM Global System for Mobile communications
IMT International Mobile Telecommunications
NOTE: Includes both IMT-2000 and IMT-Advanced RITs.
ITU-R International Telecommunication Union Radio sector
LTE Long Term Evolution
NOTE: Also known as E-UTRA.
MSG Mobile Standards Group
MSR Multi-Standard Radio
OFDMA Orthogonal Frequency Division Multiple Access
R&TTE Radio Telecommunications and Terminal Equipment
RAT Radio Access Technology
RF Radio Frequency
RIT Radio Interface Technology
RMS Root Mean Square
RRC Radio Resource Control
SDO Standard Development Organization
TDD Time Division Duplex
TDMA Time Division Multiple Access
TFES Task Force for European Standards for IMT
TIA Telecommunications Industry Association
UE User Equipment
UMB Ultra Mobile Broadband
UTRA Universal Terrestrial Radio Access
UWC Universal Wireless Communications
WMAN Wireless Metropolitan Area Network
ETSI
---------------------- Page: 10 ----------------------
11 Draft ETSI EN 301 908-1 V7.0.1 (2014-11)
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of
the present document at all times when operating within the boundary limits of the declared operational environmental
profile.
4.2 Conformance requirements
The requirements in the present document are based on the assumption that the operating band is shared between
systems of the IMT family or systems having compatible characteristics.
For BS capable of multi-band operation, the requirements in the present document apply for each supported operating
band unless otherwise stated. For emission tests, all operating bands shall be activated according to the applicable test
configuration.
4.2.1 Introduction
To meet the essential requirement under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for IMT equipment
three common essential parameters have been identified. Tables 4.2.1-1 and 4.2.1-2 provide cross-references, for UE,
repeater and BS respectively, between these essential parameters and the corresponding technical requirements for
equipment within the scope of the present document.
Table 4.2.1-1: Cross references for User Equipment (UE)
Essential parameter Corresponding technical requirements
Radiated emissions 4.2.2 Radiated emissions (UE)
Control and monitoring functions 4.2.4 Control and monitoring functions (UE)
Table 4.2.1-2: Cross references for Base Stations (BS), and repeaters
Essential parameter Corresponding technical requirements
Radiated emissions 4.2.3 Radiated emissions (BS and repeater)
NOTE: Receiver sensitivity, use of correct timing and use of correct code are covered in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.