ETSI EN 301 908-2 V5.2.1 (2011-07)
IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
REN/MSG-TFES-006-2
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 2. del: CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD) (UE)
Ta dokument velja za naslednjo vrsto radijske opreme:
• uporabniško opremo za IMT-2000 CDMA neposredno razprševanje (UTRA FDD).
Te vrste radijske opreme so zmožne delovati v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v preglednici 1-1.
Ta dokument zajema zahteve za uporabniško opremo UTRA FDD iz izdaje 3GPP 99, 4, 5, 6, 7 in 8. Poleg tega ta dokument zajema zahteve za uporabniško opremo UTRA FDD v pasovih delovanja, določenih v TS 102 735 [i.4].
OPOMBA 1: Za pas XX:
- za uporabniško opremo, načrtovano kot mobilno ali nestalno, zahteve v tem dokumentu, merjene pri antenskem vhodu, prav tako prikazujejo skladnost z ustrezno zahtevo, določeno kot TRP (skupna sevana moč), kot je opisano v Sklepu Komisije 2010/267/EU [i.7], Odločbi ECC(09)03 [i.8] in poročilu CEPT 30 [i.9];
- za uporabniško opremo, načrtovano za pritrditev ali inštalacijo, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.7], Odločbi ECC (09)03 [i.8] in poročilo CEPT 30 [i.9].
Ta dokument zajema določbe člena 3.2. Direktive 1999/5/ES [i.2] (direktive R&TTE), ki navaja, da » … radijska oprema je narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«.
Poleg tega dokumenta se preostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2], lahko uporabljajo za opremo v okviru uporabe tega dokumenta.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-2 Version 5.2.1SIST EN 301 908-2 V5.2.1:2011en01-september-2011SIST EN 301 908-2 V5.2.1:2011SLOVENSKI
STANDARD
SIST EN 301 908-2 V5.2.1:2011
ETSI EN 301 908-2 V5.2.1 (2011-07)Harmonized European Standard IMT cellular networks;Harmonized EN covering the essential requirementsof article 3.2 of the R&TTE Directive;Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE) SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 2
Reference REN/MSG-TFES-006-2 Keywords 3G, 3GPP, cellular, digital, IMT, IMT-2000, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 11 3.3 Abbreviations . 11 4 Technical requirements specifications . 12 4.1 Environmental profile . 12 4.2 Conformance requirements . 13 4.2.1 Introduction. 13 4.2.2 Transmitter maximum output power. 13 4.2.2.1 Definition . 13 4.2.2.2 Limits . 14 4.2.3 Transmitter spectrum emission mask . 14 4.2.3.1 Definition . 14 4.2.3.2 Limits . 15 4.2.3.3 Conformance . 15 4.2.4 Transmitter spurious emissions . 15 4.2.4.1 Definition . 15 4.2.4.2 Limits . 15 4.2.4.3 Conformance . 17 4.2.5 Transmitter minimum output power . 17 4.2.5.1 Definition . 17 4.2.5.2 Limits . 17 4.2.5.3 Conformance . 17 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 17 4.2.6.1 Definition . 17 4.2.6.2 Limits . 18 4.2.6.3 Conformance . 18 4.2.7 Receiver blocking characteristics . 18 4.2.7.1 Definition . 18 4.2.7.2 Limits . 18 4.2.7.3 Conformance . 20 4.2.8 Receiver spurious response . 20 4.2.8.1 Definition . 20 4.2.8.2 Limits . 20 4.2.8.3 Conformance . 20 4.2.9 Receiver intermodulation characteristics . 20 4.2.9.1 Definition . 20 4.2.9.2 Limits . 21 4.2.9.3 Conformance . 21 4.2.10 Receiver spurious emissions . 21 4.2.10.1 Definition . 21 4.2.10.2 Limits . 21 4.2.10.3 Conformance . 23 4.2.11 Out-of-synchronization handling of output power . 23 4.2.11.1 Definition . 23 4.2.11.2 Limits . 23 SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 4 4.2.11.3 Conformance . 24 4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 24 4.2.12.1 Definition . 24 4.2.12.2 Limits . 24 4.2.12.3 Conformance . 25 5 Testing for compliance with technical requirements . 25 5.1 Environmental conditions for testing . 25 5.2 Interpretation of the measurement results . 25 5.3 Essential radio test suites . 26 5.3.1 Transmitter maximum output power. 26 5.3.1.1 Method of test . 26 5.3.1.1.1 Initial conditions . 26 5.3.1.1.2 Procedure . 27 5.3.1.2 Test requirements . 27 5.3.2 Transmitter spectrum emission mask . 27 5.3.2.1 Method of test . 27 5.3.2.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 27 5.3.2.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 27 5.3.2.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 27 5.3.2.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 27 5.3.2.2 Test requirements . 28 5.3.3 Transmitter spurious emissions . 28 5.3.3.1 Method of test . 28 5.3.3.1.1 Initial conditions . 28 5.3.3.1.2 Procedure . 28 5.3.3.2 Test requirements . 28 5.3.4 Transmitter minimum output power . 28 5.3.4.1 Method of test . 28 5.3.4.1.1 Initial conditions . 28 5.3.4.1.2 Procedure . 28 5.3.4.2 Test requirements . 29 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 29 5.3.5.1 Method of test . 29 5.3.5.1.1 Initial conditions . 29 5.3.5.1.2 Procedure . 29 5.3.5.2 Test requirements . 29 5.3.6 Receiver blocking characteristics . 29 5.3.6.1 Method of test . 29 5.3.6.1.1 Initial requirements . 29 5.3.6.1.2 Procedure . 30 5.3.6.2 Test requirements . 30 5.3.7 Receiver spurious response . 30 5.3.7.1 Method of test . 30 5.3.7.1.1 Initial conditions . 30 5.3.7.1.2 Procedure . 30 5.3.7.2 Test requirements . 30 5.3.8 Receiver Intermodulation characteristics . 31 5.3.8.1 Method of test . 31 5.3.8.1.1 Initial conditions . 31 5.3.8.1.2 Procedure . 31 5.3.8.2 Test requirements . 31 5.3.9 Receiver spurious emissions . 31 5.3.9.1 Method of test . 31 5.3.9.1.1 Initial conditions . 31 5.3.9.1.2 Procedure . 31 5.3.9.2 Test requirements . 31 5.3.10 Out-of-synchronization handling of output power . 32 5.3.10.1 Method of test . 32 5.3.10.1.1 Initial conditions . 32 5.3.10.1.2 Procedure . 32 5.3.10.2 Test requirements . 32 SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 5 5.3.11 Transmitter adjacent channel leakage power ratio . 32 5.3.11.1 Method of test . 32 5.3.11.1.1 Initial conditions for UEs not supporting HSDPA and/or E-DCH . 32 5.3.11.1.1A Initial conditions for UEs supporting HSDPA and/or E-DCH . 33 5.3.11.1.2 Procedure for UEs not supporting HSDPA and/or E-DCH . 33 5.3.11.1.2A Procedure for UEs supporting HSDPA and/or E-DCH . 33 5.3.11.2 Test requirements . 33 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 34 Annex B (normative): Environmental profile . 36 B.1 General . 36 B.1.1 Introduction . 36 B.1.2 Temperature . 36 B.1.3 Voltage . 36 B.1.4 Test environment . 37 Annex C (informative): The EN title in the official languages . 38 Annex D (informative): Bibliography . 39 History . 40
SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandate M/284 from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The title and reference to the present document are intended to included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A. The present document is part 2 of a multi-part deliverable covering the essential requirements under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT cellular networks, as identified below: Part 1: "Introduction and common requirements"; Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)"; Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)"; Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)"; Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)"; Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)"; Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13:
"Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)"; SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 7 Part 14:
"Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)"; Part 15:
"Evolved Universal Terrestrial Radio Access (E-UTRA FDD) (Repeaters)"; Part 16:
"Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17:
"Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 18:
"E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)"; Part 19:
"OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)"; Part 20:
"OFDMA TDD WMAN (Mobile WiMAX) TDD Base Stations (BS)"; Part 21:
"OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)"; Part 22:
"OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates Date of adoption of this EN: 4 July 2011 Date of latest announcement of this EN (doa): 31 October 2011 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 April 2012 Date of withdrawal of any conflicting National Standard (dow): 30 April 2013
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-2 V5.2.1:2011
ETSI ETSI EN 301 908-2 V5.2.1 (2011-07) 8 1 Scope The present document applies to the following radio equipment type: • User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD operating bands UTRA FDD Band Direction of transmission UTRA FDD operating bands I Transmit 1 920 MHz to 1 980 MHz Receive 2 110 MHz to 2 170 MHz III Transmit 1 710 MHz to 1 785 MHz Receive 1 805 MHz to 1 880 MHz VII Transmit 2 500 MHz to 2 570 MHz Receive 2 620 MHz to 2 690 MHz VIII Transmit 880 MHz to 915 MHz Receive 925 MHz to 960 MHz XV Transmit 1 900 MHz to 1 920 MHz Receive 2 600 MHz to 2 620 MHz XVI Transmit 2 010 MHz to 2 025 MHz Receive
2 585 MHz to 2 600 MHz XX Transmit 832 MHz to 862 MHz Receive 791 MHz to 821 MHz
The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7 and 8. In addition, the present document covers requirements for UTRA FDD User Equipment in the operating bands specified in TS 102 735 [i.4]. NOTE 1: For Band XX: - for user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (total radiated power), as described in Commision Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9]; - for user equipment designed to be fixed or installed, the present document does not address the requirements described in Commision Decision 2010/267/EU [i.7], ECC Decision
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.