ETSI ETS 300 607-1 ed.15 (2000-09)

Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 1: Conformance specification; (GSM 11.10-1 version 4.28.1)

RE/SMG-071110PRD-1

Digitalni celični telekomunikacijski sistem (faza 2) - Specifikacija skladnosti mobilne postaje (MS) - 1. del: Specifikacija skladnosti (GSM 11.10-1, različica 4.28.1)

General Information

• Status: Published
• Publication Date: 07-Sep-2000
• Technical Committee: SMG 7 - Mobile Station (MS) Testing
• Current Stage: 12 - Completion
• Due Date: 28-Jul-2000
• Completion Date: 08-Sep-2000
• Mandate: T-247
• Ref Project: SIST ETS 300 607-1 E15:2005 - Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 1: Conformance specification; (GSM 11.10-1 version 4.28.1)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ETS 300 607-1 E15:2005
01-februar-2005
'LJLWDOQLFHOLþQLWHOHNRPXQLNDFLMVNLVLVWHPID]D6SHFLILNDFLMDVNODGQRVWL
PRELOQHSRVWDMH06GHO6SHFLILNDFLMDVNODGQRVWL*60UD]OLþLFD

Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS)
conformance specification; Part 1: Conformance specification; (GSM 11.10-1 version
4.28.1)
Ta slovenski standard je istoveten z: ETS 300 607-1 Edition 15
ICS:
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
SIST ETS 300 607-1 E15:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 607-1 E15:2005

---------------------- Page: 2 ----------------------

SIST ETS 300 607-1 E15:2005
EUROPEAN ETS 300 607-1
TELECOMMUNICATION August 2000
STANDARD Fifthteenth Edition
Source: SMG Reference: RE/SMG-071110PRD-1
ICS: 33.020
Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM)
R
GLOBAL SYSTEM FOR
MOBILE COMMUNICATIONS
Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 1: Conformance specification;
(GSM 11.10-1 version 4.28.1)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: [e-mail] - http://www.etsi.org
Tel.:[phone]- Fax:[phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2000. All rights reserved.

---------------------- Page: 3 ----------------------

SIST ETS 300 607-1 E15:2005
Page 2
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 607-1 E15:2005
Page 3
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
Contents
Foreword .25
1 Scope .27
2 Normative references.27
3 Definitions, conventions, and applicability .33
3.1 Mobile station definition and configurations.33
3.2 Applicability.33
3.2.1 Applicability of this specification.33
3.2.2 Applicability of the individual tests.34
3.2.3 Applicability to terminal equipment.55
3.3 Definitions .56
3.4 Conventions for mathematical notations .56
3.4.1 Mathematical signs.56
3.4.2 Powers to the base 10.56
3.5 Conventions on electrical terms.56
3.5.1 Radio Frequency (RF) input signal level.56
3.5.2 Reference sensitivity level.57
3.5.3 Power level of fading signal .57
3.6 Terms on test conditions.57
3.6.1 Radio test conditions.57
4 Test Equipment .58
4.1 Terms used to describe test equipment in this ETS.58
4.2 Functional requirements of test equipment .58
5 Testing methodology in general (layers 1, 2, and 3).58
5.1 Testing of optional functions and procedures.58
5.2 Test interfaces and facilities .58
5.3 Different protocol layers.59
5.4 Information to be provided by the apparatus supplier .59
5.5 Definitions of transmit and receive times.59
6 Reference test methods. .60
6.1 General .60
6.2 Choice of frequencies in the frequency hopping mode .60
6.3 "Ideal" radio conditions .60
6.4 Standard test signals. .60
6.5 Power (control) levels. .60
7 Implicit testing.61
8 Measurement uncertainty.61
9 Format of tests .61
10 Generic call set up procedures .62
10.1 Generic call set-up procedure for mobile terminating speech calls.62
10.2 Generic call set-up procedure for mobile originating speech calls .67
10.3 Generic call set-up procedure for mobile terminating data calls .70
10.4 Generic call set-up procedure for mobile originating data calls.73
11 General tests.77
11.1 Verification of support and non-support of services (multiple numbering scheme or
ISDN) .77

---------------------- Page: 5 ----------------------

SIST ETS 300 607-1 E15:2005
Page 4
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
11.1.1 Mobile Terminated (MT) calls . 77
11.1.2 Mobile Originated (MO) calls . 78
11.2 Verification of support of the single numbering scheme . 79
11.3 Verification of non-support of services (Advice of Charge Charging (AoCC)). 80
11.4 Verification of non-support of services (call hold) . 81
11.5 Verification of non-support of services (multiparty). 82
11.6 Verification of non-support of feature (Fixed Dialling Number (FDN)). 83
11.7 IMEI Security. 84
11.8 Coding of the Bearer Capability information element . 85
11.8.1 Network to MS Direction. 86
11.8.1.1 BS 21 to 26 - Asynchronous Service . 86
11.8.1.1.1 BS 21. 86
11.8.1.1.2 BS 22. 90
11.8.1.1.3 BS 24. 90
11.8.1.1.4 BS 25. 90
11.8.1.1.5 BS 26. 90
11.8.1.1.6 BS 23. 90
11.8.1.2 BS 31 to 34 - Synchronous Service. 91
11.8.1.2.1 BS 32. 91
11.8.1.2.2 BS 31. 95
11.8.1.2.3 BS 33. 96
11.8.1.2.4 BS 34. 96
11.8.1.3 BS 61 - Alternate Speech / Data. 96
11.8.1.3.1 Speech/Asynchronous Data,
Transparent. 97
11.8.1.3.2 Speech/Asynchronous Data, Non
Transparent. 99
11.8.1.3.3 Speech/Synchronous Data . 101
11.8.1.4 BS 81 - Speech followed by Data . 102
11.8.1.4.1 Speech followed by Asynchronous
Data. 102
11.8.1.4.2 Speech followed by Synchronous
Data. 102
11.8.1.5 TS 61 - Alternate Speech / Facsimile group 3. 102
11.8.1.5.1 TS 61 - Alternate Speech / Facsimile
group 3, Transparent. 103
11.8.1.5.2 TS 61 - Alternate Speech / Facsimile
group 3, Non-Transparent. 104
11.8.1.6 TS 62 - Automatic Facsimile group 3. 105
11.8.2 MS to SS direction. 105
11.8.2.1 BS 21 to 26 - Asynchronous Service . 105
11.8.2.1.1 BS 21. 106
11.8.2.1.2 BS 22. 110
11.8.2.1.3 BS 24. 110
11.8.2.1.4 BS 25. 110
11.8.2.1.5 BS 26. 110
11.8.2.1.6 BS 23. 110
11.8.2.2 BS 31 to 34 - Synchronous Service. 111
11.8.2.2.1 BS 32. 111
11.8.2.2.2 BS 31. 115
11.8.2.2.3 BS 33. 116
11.8.2.2.4 BS 34. 116
11.8.2.3 BS 41 to 46 - PAD Access Asynchronous . 117
2)
11.8.2.3.1 BS 41 . 117
11.8.2.3.2 BS 42. 118
11.8.2.3.3 BS 44. 119
11.8.2.3.4 BS 45. 119
11.8.2.3.5 BS 46. 119
11.8.2.3.6 BS 43. 119
11.8.2.4 BS 51 to 53 - Packet Service Synchronous. 120
2)
11.8.2.4.1 BS 51 . 120
11.8.2.4.2 BS 52. 120
11.8.2.4.3 BS 53. 120

---------------------- Page: 6 ----------------------

SIST ETS 300 607-1 E15:2005
Page 5
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
11.8.2.5 BS 61 - Alternate Speech / Data .121
11.8.2.5.1 Speech/Asynchronous Data,
Transparent.121
11.8.2.5.2 Speech/Asynchronous Data, Non
Transparent.124
11.8.2.5.3 Speech/Synchronous Data.126
11.8.2.6 BS 81 - Speech followed by Data.127
11.8.2.6.1 Speech followed by Asynchronous
Data .127
11.8.2.6.2 Speech followed by Synchronous
Data .127
11.8.2.7 TS 61 - Alternate Speech / Facsimile group 3.127
11.8.2.7.1 TS 61 - Alternate Speech / Facsimile
group 3, Transparent .128
11.8.2.7.2 TS 61 - Alternate Speech / Facsimile
group 3, Non Transparent.129
11.8.2.8 TS 62 - Automatic Facsimile group 3 .130
11.8.2.9 TS 11 and TS 12- Speech.130
11.8.2.9.1 Support of only full/half rate speech
version 1 .130
11.8.2.9.2 Support of speech full rate version 2
(Enhanced Full Rate).130
12 Transceiver.132
12.1 Conducted spurious emissions.132
12.1.1 MS allocated a channel.132
12.1.2 MS in idle mode.133
12.2 Radiated spurious emissions.135
12.2.1 MS allocated a channel.135
12.2.2 MS in idle mode.137
13 Transmitter .140
13.1 Frequency error and phase error.140
13.2 Frequency error under multipath and interference conditions.143
13.3 Transmitter output power and burst timing .145
13.4 Output RF spectrum .152
13.5 Intermodulation attenuation .158
14 Receiver .160
14.1 Bad frame indication .166
14.1.1 Bad frame indication - TCH/FS .166
14.1.1.1 Bad frame indication - TCH/FS - Random RF input.166
14.1.1.2 Bad frame indication - TCH/FS - Frequency hopping and
downlink DTX.167
14.1.2 Bad frame indication - TCH/HS.168
14.1.2.1 Bad frame indication - TCH/HS - Random RF input.168
14.1.2.2 Bad frame indication - TCH/HS - Frequency hopping and
downlink DTX.169
14.1.3 Bad frame indication - TCH/FS - Frequency hopping and downlink DTX -
Phase 2 MS in a phase 1 network .170
14.1.4 Bad frame indication - TCH/HS - Frequency hopping and downlink DTX -
Phase 2 MS in a phase 1 network .172
14.2 Reference sensitivity.175
14.2.1 Reference sensitivity - TCH/FS.175
14.2.2 Reference sensitivity - TCH/HS (Speech frames).177
14.2.3 Reference sensitivity - FACCH/F .180
14.2.4 Reference sensitivity - FACCH/H.181
14.2.5 Reference sensitivity - full rate data channels .182
14.2.6 Reference sensitivity - half rate data channels .183
14.2.7 Reference sensitivity - TCH/EFS .184
14.3 Usable receiver input level range .186
14.4 Co-channel rejection.187
14.4.1 Co-channel rejection - TCH/FS. .187

---------------------- Page: 7 ----------------------

SIST ETS 300 607-1 E15:2005
Page 6
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
14.4.2 Co-channel rejection - TCH/HS . 189
14.4.3 Co-channel rejection - TCH/HS (SID frames) . 191
14.4.4 Co-channel rejection - FACCH/F. 193
14.4.5 Co-channel rejection - FACCH/H . 194
14.4.6 Co-channel rejection - TCH/EFS. . 195
14.5 Adjacent channel rejection. 196
14.5.1 Adjacent channel rejection - speech channels . 196
14.5.2 Adjacent channel rejection - control channels. 199
14.6 Intermodulation rejection. 201
14.6.1 Intermodulation rejection - speech channels. 201
14.6.2 Intermodulation rejection - control channels. 203
14.7 Blocking and spurious response . 204
14.7.1 Blocking and spurious response - speech channels . 204
14.7.2 Blocking and spurious response - control channels . 207
14.8 AM suppression . 211
14.8.1 AM suppression - speech channels. 211
14.8.2 AM suppression - control channels . 212
14.9 Paging performance at high input levels. 214
15 Timing advance and absolute delay. 216
16 Reception time tracking speed . 218
17 Access times during handover . 220
17.1 Intra cell channel change . 220
17.2 Inter cell handover. 222
18 Temporary reception gaps. 225
19 Channel release after unrecoverable errors. 227
19.1 Channel release after unrecoverable errors -1 . 227
19.2 Channel release after unrecoverable errors - 2 . 228
19.3 Channel release after unrecoverable errors - 3 . 229
20 Cell selection and reselection. 231
20.1 Cell selection. 232
20.2 Cell selection with varying signal strength values. 234
20.3 Basic cell reselection. 236
20.4 Cell reselection using TEMPORARY_OFFSET, CELL_RESELECT_OFFSET,
POWER_OFFSET and PENALTY_TIME parameters. 238
20.5 Cell reselection using parameters transmitted in the System Information type 2bis,
type 2ter, type 7 and type 8 messages. . 240
20.6 Cell reselection timings . 242
20.7 Priority of cells. 244
20.8 Cell reselection when C1 (serving cell) < 0 for 5 seconds. 245
20.9 Running average of the surrounding cell BCCH carrier signal levels . 246
20.10 Running average of the serving cell BCCH carrier signal level . 247
20.11 Updating the list of six strongest neighbour carriers and decoding the BCCH
information of a new carrier on the list . 249
20.12 Decoding the BCCH information of the neighbour carriers on the list of six strongest
neighbour carriers . 250
20.13 Decoding the BSIC of the neighbour carriers on the list of six strongest neighbour
carriers . 251
20.14 Emergency calls. 252
20.15 Cell reselection due to MS rejection "LA not allowed" . 253
20.16 Downlink signalling failure. 255
20.17 Cell selection if no suitable cell found in 10 s . 256
20.18 Cell reselection due to MS rejection "Roaming not allowed in this LA" . 257
20.19 Cell selection on release of SDCCH and TCH. 258
20.20 Multiband cell selection and reselection . 260
20.20.1 Multiband cell selection and reselection / Cell Selection. 260
20.20.2 Multiband cell selection and reselection / Cell reselection . 262

---------------------- Page: 8 ----------------------

SIST ETS 300 607-1 E15:2005
Page 7
ETS 300 607-1 (GSM 11.10-1 version 4.28.1): August 2000
21 Received signal measurements.264
21.1 Signal strength.264
21.2 Signal strength selectivity .267
21.3 Signal quality under static conditions .268
21.3.1 Signal quality under static conditions - TCH/FS.268
21.3.2 Signal quality under static conditions - TCH/HS .270
21.4 Signal quality under TU50 propagation conditions.272
22 Transmit power control timing and confirmation .275
23 Single frequency reference .276
24 Tests of the layer 1 signalling functions .277
25 Tests of the layer 2 signalling functions .278
25.1 Introduction, objective and scope .278
25.1.1 General.278
25.1.2 Test configurations .278
25.1.3 Pre-conditions .278
25.1.4 Layer 2 test frames.279
25.1.5 Establishment of the dedicated physical resource.279
25.1.6 Release of the dedicated physical resource .280
25.2 Test sequences.280
25.2.1 Initialization.281
25.2.1.1 Initialization when contention resolution required.281
25.2.1.1.1 Normal initialization.281
25.2.1.1.2 Initialization failure .282
25.2.1.1.3 Initialization denial .285
25.2.1.1.4 Total initialization failure .286
25.2.1.2 Initialization, contention resolution not required .287
25.2.1.2.1 Normal initialization without
contention resolution.287
25.2.1.2.2 Initialization failure .288
25.2.1.2.3 Initialization denial .289
25.2.1.2.4 Total initialization failure .290
25.2.2 Normal information transfer.291
25.2.2.1 Sequence counting and I frame acknowledgements .291
25.2.2.2 Receipt of an I frame in the timer recovery state.294
25.2.2.3 Segmentation and concatenation.296
25.2.3 Normal layer 2 disconnection.299
25.2.4 Test of link failure .299
25.2.4.1 I frame loss (MS to SS) .299
25.2.4.2 RR response frame loss (SS to MS) .301
25.2.4.3 RR response frame loss (MS to SS) .301
25.2.5 Test of frame transmission with incorrect C/R values.302
25.2.5.1 I frame with C bit set to zero.302
25.2.5.2 SABM frame with C bit set to zero .303
25.2.6 Test of errors in the control field.304
25.2.6.1 N(S) sequence error .304
25.2.6.2 N(R) sequ
...