ETSI EN 301 614-3 V1.1.2 (1999-02)

Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 3: Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)

DEN/DECT-040104-3

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Digitalno omrežje z integriranimi storitvami (ISDN) - Vzajemno delovanje DECT/ISDN v obliki posredovalnega sistema - 3. del: Preskuševalna specifikacija, odvisna od profila (PSTS), za fiksno radijsko zaključitev (FT)

General Information

• Status: Published
• Publication Date: 16-Feb-1999
• Technical Committee: DECT 4 - DECT Testing aspects
• Current Stage: 12 - Completion
• Due Date: 08-Jan-1999
• Completion Date: 17-Feb-1999
• Mandate: BC-T-317/4
• Mandate: T-306
• Ref Project: SIST EN 301 614-3:2000 - Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 3: Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.REOLNLDigital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 3: Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 301 614-3 V1.1.23SIST EN 301 614-3:en01-QRYHPEHr-3SIST EN 301 614-3:SLOVENSKI
STANDARD
EN 301 614-3 V1.1.2 (1999-02)European Standard (Telecommunications series)Digital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN);DECT/ISDN interworking forintermediate system configuration;Part 3: Profile Specific Test Specification (PSTS) forFixed radio Termination (FT)SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)2ReferenceDEN/DECT-040104-3 (ey0r0idc.PDF)KeywordsDECT, ICS, ISDN, profileETSIPostal addressF-06921 Sophia Antipolis Cedex - FRANCEOffice address650 Route des Lucioles - Sophia AntipolisValbonne - FRANCETel.: [phone]
Fax: [phone]Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/[e-mail] copies of this ETSI deliverablecan be downloaded fromhttp://www.etsi.orgIf you find errors in the present document, send yourcomment to: [e-mail] NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1999.All rights reserved.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)3ContentsIntellectual Property Rights.7Foreword.71Scope.82Normative references.83Definitions and abbreviations.103.1Definitions.103.2Abbreviations.114DECT NWK layer protocol.124.1Additional test purposes.124.1.1Additional test purposes for IIP CC specific behaviours.134.1.1.1Test group FT/CC/BV/IS.134.2Abstract test method.134.3Relevant test cases.134.4Additional test cases.154.5Modified test cases.155DECT DLC layer protocol.165.1Additional test purposes.165.1.1Additional test purposes for C-plane Class B procedures.175.1.1.1Test group CA.175.1.1.2Test group BV.195.1.1.3Test group BI.205.1.1.4Test group BO.215.1.2Additional test purposes for U-plane LU7 procedures.225.1.2.1Test group BV.225.1.3Additional test purposes for U-plane LU8 procedures.225.1.3.1Test group BV.225.2Abstract test method.235.3Relevant test cases.235.4Additional test cases.235.4.1Additional test cases for C-plane Class B.235.4.2Additional test cases for U-plane LU7.235.4.3Additional test cases for U-plane LU8.235.5Modified test cases.236DECT MAC layer protocol.246.1Additional test purposes.246.1.1Additional test purposes for advanced symmetric connections.256.1.2Additional test purposes for C-plane switching procedures.256.1.2.1Dynamic switching CF to CS: DIFS initiated.256.1.2.2Dynamic switching CS to CF: DIPS initiated.266.1.2.3Dynamic switching CS to CF: DIFS initiated.266.1.2.4Dynamic switching CSx to CSy: DIFS initiated.276.1.3Additional test purposes for U-plane switching procedures.276.1.3.1Connection handover procedure.276.1.3.2Release of part of double slot procedure.276.2Abstract test method.286.3Relevant test cases.286.4Additional test cases.296.4.1Additional test cases for advanced symmetric connections.296.4.2Additional test cases for C-plane switching procedures.296.4.3Additional test cases for U-plane switching procedures.296.5Modified test cases.29SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)47DECT PHL layer protocol.297.1Additional test purposes.297.2Abstract test method.297.3Relevant test cases.297.4Additional test cases.307.5Modified test cases.308ISDN basic access protocols.308.1Applicability of ATS.308.2Additional test purposes.308.3Abstract test method.308.4Relevant test cases.309DECT/ISDN IIP profile.319.1Profile test suite structure.319.1.1Test groups.319.1.1.1Functional modules.319.1.1.2Main test groups.319.1.1.2.1Capability (CA) tests.329.1.1.2.2Valid Behaviour (BV) tests.329.1.1.2.3Inopportune Behaviour (BO) tests.329.1.1.2.4Invalid Behaviour (BI) tests.329.2Profile test purposes.329.2.1TP definition conventions.329.2.2TP naming conventions.339.2.3Sources of TP definitions.349.2.4Test purposes for IWU Link Association Entity.349.2.5Test purposes for IWU missing resource management.359.2.6Test purposes for IWU Call Control specific procedures.359.2.7Test purposes for call release procedures.369.3Profile Abstract Test Method (ATM).379.4Profile Untestable test purposes.389.5Profile ATS Conventions.389.5.1Declarations part naming conventions.389.5.1.1Type and structured type definitions.389.5.1.2Operations definitions.389.5.1.3Parameter declarations.389.5.1.4Selection expression definitions.399.5.1.5Constant declarations.399.5.1.6Test suite variable declarations.399.5.1.7Test case variable declarations.399.5.1.8PCO declarations.399.5.1.9Timer declarations.399.5.1.10ASP type definitions.409.5.1.11PDU type definitions.409.5.1.12Alias definitions.409.5.2Constraints part naming conventions.409.5.3Dynamic part naming conventions.409.5.3.1Test Case identifier.419.5.3.2Test step identifier.419.5.3.3Default identifier.419.5.3.4General aspects.419.5.3.5ATS abbreviations.429.5.4Declaration part implementation conventions.429.5.5Constraint part implementation conventions.429.5.6Dynamic part implementation conventions.429.5.7Documentation implementation conventions.439.6Test case and test purpose mapping.43SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)5Annex A (normative):Profile Implementation eXtra Information for Testing (IXIT)proforma.44A.1Identification summary.44A.2ATS summary.44A.3Test laboratory.44A.4Client identification.45A.5SUT.45A.6Profile information.46A.6.1NWK layer.46A.6.2DLC layer.48A.6.3MAC layer.50Annex B (normative):Profile Conformance Test Report (Profile CTR) proforma.52B.1Identification summary.52B.1.1Protocol conformance test report.52B.1.2IUT identification.52B.1.3Testing environment.53B.1.4Limits and reservation.53B.1.5Comments.53B.2IUT conformance status.53B.3Static conformance summary.54B.4Dynamic conformance summary.54B.5Static conformance review report.54B.6Test campaign report.55B.7Observations.55Annex C (normative):System Conformance Test Report (SCTR) proforma.56C.1Identification summary.56C.1.1System conformance test report.56C.1.2Test laboratory.56C.1.3Client identification.57C.1.4System Under Test (SUT).57C.1.5Profile identification.57C.1.6Nature of conformance testing.58C.1.7Limits and reservations.58C.1.8Record of agreement.58C.1.9Comments.59C.2System report summary for DECT/ISDN IIP FT.59C.2.1Profile testing summary for DECT NWK layer protocol.59C.2.2Profile testing summary for DECT DLC layer protocol.60C.2.3Profile testing summary for DECT MAC layer protocol.61C.2.4Profile testing summary for DECT PHL layer protocol.62C.2.5Profile testing summary for ISDN L2, L1 basic access protocol.63C.2.6Profile testing summary for DECT/ISDN IIP profile.64Annex D (normative):Profile eXtra Requirement List (XRL) proforma.65D.1Profile eXtra Requirement List for IIP - FT part.65D.1.1Parameters for IWU layer.65D.1.2Specific parameters for NWK layer.66D.1.3Specific parameters for DLC layer.67D.1.4Specific parameters for MAC layer.67SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)6Annex E (normative):Modifications of the DECT CI PCTR proforma.68E.1Modifications of DECT NWK layer PCTR proforma.68E.2Modifications of DECT DLC layer PCTR proforma.71E.3Modifications of DECT MAC layer PCTR proforma.74E.4Observations.76Annex F (normative):Abstract Test Suite (ATS) - NWK layer.77F.1The TTCN Graphical form (TTCN.GR).77F.2The TTCN Machine Processable form (TTCN.MP).77Annex G (normative):Abstract Test Suite (ATS) - DLC layer.78G.1The TTCN Graphical form (TTCN.GR).78G.2The TTCN Machine Processable form (TTCN.MP).78Annex H (normative):Abstract Test Suite (ATS) - MAC layer.79H.1The TTCN Graphical form (TTCN.GR).79H.2The TTCN Machine Processable form (TTCN.MP).79Annex J (normative):Abstract Test Suite (ATS) - Interworking Unit.80J.1The TTCN Graphical form (TTCN.GR).80J.2The TTCN Machine Processable form (TTCN.MP).80History.81SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)7Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respectof ETSI standards", which is available free of charge from the ETSI Secretariat. Latest updates are available on theETSI Web server (http://www.etsi.org/ipr).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)which are, or may be, or may become, essential to the present document.ForewordThis European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced CordlessTelecommunications (DECT).The present document is part 3 of a multi-part EN covering the DECT/ISDN interworking for intermediate systemconfiguration, as identified below:Part 1:"Profile Test Specification (PTS) summary";Part 2:"Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)".National transposition datesDate of adoption of this EN:25 December 1998Date of latest announcement of this EN (doa):31 March 1999Date of latest publication of new National Standardor endorsement of this EN (dop/e):30 September 1999Date of withdrawal of any conflicting National Standard (dow):30 September 1999SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)81ScopeThe present document contains the test specification for Digital Enhanced Cordless Telecommunications/IntegratedServices Digital Network (DECT/ISDN) Interworking for Intermediate system Profile (IIP) Fixed Part (FP) applicationsas specified in ETS 300 822 [6].This test specification provides conformance tests for DECT/ISDN terminal equipment conforming to ETS 300 822 [6].The main objective is to perform a high probability of inter-operability between the DECT/ISDN terminal equipmentand an ISDN network. The DECT/ISDN terminal equipment contains Fixed Parts (FPs) and Portable Parts (PPs) thatmay be supplied by different manufacturers.The ISO standard for the methodology of conformance testing ISO/IEC 9646 [19] to [25] is used as the basis for the testmethodology, and as the basis for test case specification.The test cases if listed in the present document have been derived from the corresponding ATS. Additional DECT/ISDNIIP specific test cases are included where required.Annex A provides Profile Implementation eXtra Information for Testing (IXIT) proforma part of the present document.Annex B provides Profile Conformance Test Report (Profile CTR) proforma part of the present document.Annex C provides System Conformance Test Report (SCTR) proforma part of the present document.Annex D provides the Profile X Requirement List (XRL) proforma part of the present document.Annex E provides modifications of DECT layer PCTR proforma of the present document.Annex F provides the Tree and Tabular Combined Notation (TTCN) part for DECT NWK layer conforming to therequirements of the present document.Annex G provides the TTCN part for DECT DLC layer conforming to the requirements of the present document.Annex H provides the TTCN part for DECT MAC layer conforming to the requirements of the present document.Annex I provides the TTCN part for DECT/ISDN IWU - IIP profile.2Normative referencesReferences may be made to:a)specific versions of publications (identified by date of publication, edition number, version number, etc.), inwhich case, subsequent revisions to the referenced document do not apply; orb)all versions up to and including the identified version (identified by "up to and including" before the versionidentity); orc)all versions subsequent to and including the identified version (identified by "onwards" following the versionidentity); ord)publications without mention of a specific version, in which case the latest version applies.A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the samenumber.[1]EN 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 2: Physical Layer (PHL)".[2]EN 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 3: Medium Access Control (MAC) layer".[3]EN 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 4: Data Link Control (DLC) layer".SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)9[4]EN 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 5: Network (NWK) layer".[5]EN 300 444 (1997): "Digital Enhanced Cordless Telecommunications (DECT); Generic AccessProfile (GAP)".[6]ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration;Interworking and profile specification".[7]EN 300 176: "Digital Enhanced Cordless Telecommunications (DECT); Approval testspecification".[8]ETS 300 476-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 4: Network (NWK)layer - Fixed radio Termination (FT)".[9]ETS 300 476-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 5: Data LinkControl (DLC) layer - Fixed radio Termination (FT)".[10]ETS 300 476-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 6: Medium AccessControl (MAC) layer - Fixed radio Termination (FT)".[11]ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer".[12]EN 301 241-2: "Digital Enhanced Cordless Telecommunications (DECT)/Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; ProfileImplementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)".[13]EN 300 497-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for MediumAccess Control (MAC) layer".[14]EN 300 497-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 3: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Fixed radio Termination (FT)".[15]EN 300 497-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - Data LinkControl (DLC) layer".[16]EN 300 497-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC) layer".[17]EN 300 497-8: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 8: Test Suite Structure (TSS) and Test Purposes (TP) - Network(NWK) layer - Fixed radio Termination (FT)".[18]EN 300 497-9: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 9: Abstract Test Suite (ATS) for Network (NWK) layer - Fixedradio Termination (FT)".[19]ISO/IEC 9646-1 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 1: General concepts". (See also CCITTRecommendation X.290 (1991)).[20]ISO/IEC 9646-2 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 2: Abstract Test Suite specification". (See also CCITTRecommendation X.291 (1991)).SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)10[21]ISO/IEC 9646-3 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 3: The Tree and Tabular Combined Notation". (See alsoCCITT Recommendation X.292 (1992)).[22]ISO/IEC 9646-4 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 4: Test realization". (See also CCITTRecommendation X.292 (1992)).[23]ISO/IEC 9646-5 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 5: Requirements on test laboratories and clients for theconformance assessment process". (See also CCITT Recommendation X.292 (1992)).[24]ISO/IEC 9646-6 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 6: Protocol profile test specification".[25]ISO/IEC 9646-7 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 7: Implementation Conformance Statement".[26]ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 2: General protocolspecification [ITU-T Recommendation Q.921 (1993), modified]".[27]ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 4: Protocol Implementation ConformanceStatement (PICS) proforma specification for the general protocol".[28]ETS 300 012 (1992) including Amendment 2 (1996): "Integrated Services Digital Network(ISDN); Basic user-network interface; Layer 1 specification and test principles".[29]Void.[30]TBR 3: "Integrated Services Digital Network (ISDN); Attachment requirements for terminalequipment to connect to an ISDN using ISDN basic access".[31]TBR 22: "Radio Equipment and Systems (RES); Attachment requirements for terminal equipmentfor Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP)applications".[32]EN 300 497-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Portable radio Termination (PT)".3Definitions and abbreviations3.1DefinitionsFor the purposes of the present document, the following terms and definitions apply:a)The terms defined in ISO/IEC 9646-7 [25]; andb)The definitions in ETS 300 822 [6].SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)113.2AbbreviationsFor the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 [19], ISO/IEC 9646-6 [24],ISO/IEC 9646-7 [25] and the abbreviations defined in ETS 300 822 [6], apply. In particular, the following abbreviationsapply:ASPAbstract Service PrimitiveATMAbstract Test MethodATSAbstract Test SuiteBIInvalid BehaviourBOInopportune BehaviourBVValid BehaviourCACapability testsCCCall Control entityCICommon InterfaceDECTDigital Enhanced Cordless TelecommunicationsDLCData Link Control layerFTFixed radio TerminationGAPGeneric Access ProfileICSImplementation Conformance StatementISDNIntegrated Services Digital NetworkISOInternational Organization for StandardizationIUTImplementation Under TestIXITImplementation eXtra Information for TestingIWPInterworking ProfileLCELink Control EntityLTLower TesterMACMedium Access Control layerMMMobility Management entityMTCMain Test ComponentNWKNetwork layerPDUProtocol Data UnitPHLPhysical layerPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPSTSProfile Specific Test SpecificationPTPortable radio TerminationPTSProfile Test SpecificationSAPService Access PointSCSSystem Conformance StatementSDUService Data UnitSUTSystem Under TestTPTest PurposeTSSTest Suite StructureXRLIXIT Requirements listSIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)124DECT NWK layer protocol4.1Additional test purposesFigure 1 shows the Network (NWK) Test Suite Structure (TSS) defined in EN 300 497-8 [17] for the conformancetesting.CCLCICCICRSCBVBIITBVBITIBVBVTIISMLLRLSRSBOTIBIBVMOBVLLLEAUPRKACACABOMMLOPMNWKMEBOOCITIDARCHFigure 1: NWK TSSNo test purpose for CC entity of the NWK layer as specified in EN 300 497-8 [17] applies without modification.Some of the test purposes for LCE entity of the NWK layer as specified in EN 300 497-8 [17] apply with nomodifications.No test purpose for CISS entity of the NWK layer is relevant.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)134.1.1Additional test purposes for IIP CC specific behaviours4.1.1.1Test group FT/CC/BV/ISTP_FT_CC_BV_IS_01ETS 300 822 [6], subclause 6.5Initial condition: CC is idle, no link is establishedCheck that, upon receipt of a correct {IWU_INFO} message containing a ISDN{SET-UP} requesting a U-plane, the IUT will reply by sending a {CC_SETUP} foran outgoing callTP_FT_CC_BV_IS_02ETS 300 822 [6], subclause 6.5Initial condition: CC is idle, no link is establishedCheck that, upon receipt of a {IWU_INFO} message containing an invalid ISDN{SET-UP}, the IUT will not reply by sending a {CC_SETUP} for an outgoing callTP_FT_CC_BV_IS_05ETS 300 822 [6], subclause 12.2.1Initial condition: a link is established, using a LU1 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU1 to LU7.TP_FT_CC_BV_IS_06ETS 300 822 [6], subclause 12.2.2Initial condition: a link is established, using a LU7 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU7 to LU1.TP_FT_CC_BV_IS_07ETS 300 822 [6], subclause 12.2.3Initial condition: a link is established, using a LU1 service U-planeCheck that the IUT after detecting the switching request (detecting the 2 100 Hzmodem tone over the U-plane link) starts the switching procedure from LU1 fullslot to LU8 double slot.TP_FT_CC_BV_IS_08ETS 300 822 [6], subclause 12.2.4Initial condition: a link is established, using a LU8 service U-planeCheck that the IUT after detecting the switching request starts the switchingprocedure from LU8 double slot to LU1 full slot.TP_FT_CC_BV_IS_09ETS 300 822 [6], subclause 12.2.4.1Initial condition: a link is established, using a LU7 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU7 to LU8.TP_FT_CC_BV_IS_10ETS 300 822 [6], subclause 12.2.4.1Initial condition: a link is established, using a LU8 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU8 to LU7.TP_FT_CC_BV_IS_11ETS 300 822 [6], subclause 6.7.3Initial condition: one link is established point to point configuration.Verify that the IUT, upon receipt of a DISCONNECT in the <> a{IWU-INFO}, initiates a disconnection from the network.4.2Abstract test methodAs stated in EN 300 497-9 [18], the ATM used for the DECT NWK layer is the remote embedded test method.The DECT/ISDN IIP implies no modification for the definition and the use of the ATM.4.3Relevant test casesThe test cases defined for the test group "FT/CC/BV/OC" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/IC" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/CI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/CR" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/RS" in EN 300 497-9 [18] are not relevant for the IIP profile.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)14The test cases defined for the test group "FT/CC/BV/BO" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/TI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/MM/BV/ID" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:-TC-FT-MM-BV-ID-01.The test cases defined for the test group "FT/MM/BV/AU" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-AU-01, TC-FT-MM-BV-AU-04, TC-FT-MM-BV-AU-05, TC-FT-MM-BV-AU-06.The test cases defined for the test group "FT/MM/BV/LO" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-LO-01, TC-FT-MM-BV-LO-02, TC-FT-MM-BV-LO-03, TC-FT-MM-BV-LO-05,TC-FT-MM-BV-LO-06.The test cases defined for the test group "FT/MM/BV/AR" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-AR-01, TC-FT-MM-BV-AR-03, TC-FT-MM-BV-AR-06.The test cases defined for the test group "FT/MM/BV/KA" in EN 300 49
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.REOLNLDigital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 3: Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 301 614-3 Version 1.1.2SIST EN 301 614-3:2000en01-januar-2000SIST EN 301 614-3:2000SLOVENSKI
STANDARD
EN 301 614-3 V1.1.2 (1999-02)European Standard (Telecommunications series)Digital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN);DECT/ISDN interworking forintermediate system configuration;Part 3: Profile Specific Test Specification (PSTS) forFixed radio Termination (FT)SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)2ReferenceDEN/DECT-040104-3 (ey0r0idc.PDF)KeywordsDECT, ICS, ISDN, profileETSIPostal addressF-06921 Sophia Antipolis Cedex - FRANCEOffice address650 Route des Lucioles - Sophia AntipolisValbonne - FRANCETel.: [phone]
Fax: [phone]Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/[e-mail] copies of this ETSI deliverablecan be downloaded fromhttp://www.etsi.orgIf you find errors in the present document, send yourcomment to: [e-mail] NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1999.All rights reserved.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)3ContentsIntellectual Property Rights.7Foreword.71Scope.82Normative references.83Definitions and abbreviations.103.1Definitions.103.2Abbreviations.114DECT NWK layer protocol.124.1Additional test purposes.124.1.1Additional test purposes for IIP CC specific behaviours.134.1.1.1Test group FT/CC/BV/IS.134.2Abstract test method.134.3Relevant test cases.134.4Additional test cases.154.5Modified test cases.155DECT DLC layer protocol.165.1Additional test purposes.165.1.1Additional test purposes for C-plane Class B procedures.175.1.1.1Test group CA.175.1.1.2Test group BV.195.1.1.3Test group BI.205.1.1.4Test group BO.215.1.2Additional test purposes for U-plane LU7 procedures.225.1.2.1Test group BV.225.1.3Additional test purposes for U-plane LU8 procedures.225.1.3.1Test group BV.225.2Abstract test method.235.3Relevant test cases.235.4Additional test cases.235.4.1Additional test cases for C-plane Class B.235.4.2Additional test cases for U-plane LU7.235.4.3Additional test cases for U-plane LU8.235.5Modified test cases.236DECT MAC layer protocol.246.1Additional test purposes.246.1.1Additional test purposes for advanced symmetric connections.256.1.2Additional test purposes for C-plane switching procedures.256.1.2.1Dynamic switching CF to CS: DIFS initiated.256.1.2.2Dynamic switching CS to CF: DIPS initiated.266.1.2.3Dynamic switching CS to CF: DIFS initiated.266.1.2.4Dynamic switching CSx to CSy: DIFS initiated.276.1.3Additional test purposes for U-plane switching procedures.276.1.3.1Connection handover procedure.276.1.3.2Release of part of double slot procedure.276.2Abstract test method.286.3Relevant test cases.286.4Additional test cases.296.4.1Additional test cases for advanced symmetric connections.296.4.2Additional test cases for C-plane switching procedures.296.4.3Additional test cases for U-plane switching procedures.296.5Modified test cases.29SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)47DECT PHL layer protocol.297.1Additional test purposes.297.2Abstract test method.297.3Relevant test cases.297.4Additional test cases.307.5Modified test cases.308ISDN basic access protocols.308.1Applicability of ATS.308.2Additional test purposes.308.3Abstract test method.308.4Relevant test cases.309DECT/ISDN IIP profile.319.1Profile test suite structure.319.1.1Test groups.319.1.1.1Functional modules.319.1.1.2Main test groups.319.1.1.2.1Capability (CA) tests.329.1.1.2.2Valid Behaviour (BV) tests.329.1.1.2.3Inopportune Behaviour (BO) tests.329.1.1.2.4Invalid Behaviour (BI) tests.329.2Profile test purposes.329.2.1TP definition conventions.329.2.2TP naming conventions.339.2.3Sources of TP definitions.349.2.4Test purposes for IWU Link Association Entity.349.2.5Test purposes for IWU missing resource management.359.2.6Test purposes for IWU Call Control specific procedures.359.2.7Test purposes for call release procedures.369.3Profile Abstract Test Method (ATM).379.4Profile Untestable test purposes.389.5Profile ATS Conventions.389.5.1Declarations part naming conventions.389.5.1.1Type and structured type definitions.389.5.1.2Operations definitions.389.5.1.3Parameter declarations.389.5.1.4Selection expression definitions.399.5.1.5Constant declarations.399.5.1.6Test suite variable declarations.399.5.1.7Test case variable declarations.399.5.1.8PCO declarations.399.5.1.9Timer declarations.399.5.1.10ASP type definitions.409.5.1.11PDU type definitions.409.5.1.12Alias definitions.409.5.2Constraints part naming conventions.409.5.3Dynamic part naming conventions.409.5.3.1Test Case identifier.419.5.3.2Test step identifier.419.5.3.3Default identifier.419.5.3.4General aspects.419.5.3.5ATS abbreviations.429.5.4Declaration part implementation conventions.429.5.5Constraint part implementation conventions.429.5.6Dynamic part implementation conventions.429.5.7Documentation implementation conventions.439.6Test case and test purpose mapping.43SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)5Annex A (normative):Profile Implementation eXtra Information for Testing (IXIT)proforma.44A.1Identification summary.44A.2ATS summary.44A.3Test laboratory.44A.4Client identification.45A.5SUT.45A.6Profile information.46A.6.1NWK layer.46A.6.2DLC layer.48A.6.3MAC layer.50Annex B (normative):Profile Conformance Test Report (Profile CTR) proforma.52B.1Identification summary.52B.1.1Protocol conformance test report.52B.1.2IUT identification.52B.1.3Testing environment.53B.1.4Limits and reservation.53B.1.5Comments.53B.2IUT conformance status.53B.3Static conformance summary.54B.4Dynamic conformance summary.54B.5Static conformance review report.54B.6Test campaign report.55B.7Observations.55Annex C (normative):System Conformance Test Report (SCTR) proforma.56C.1Identification summary.56C.1.1System conformance test report.56C.1.2Test laboratory.56C.1.3Client identification.57C.1.4System Under Test (SUT).57C.1.5Profile identification.57C.1.6Nature of conformance testing.58C.1.7Limits and reservations.58C.1.8Record of agreement.58C.1.9Comments.59C.2System report summary for DECT/ISDN IIP FT.59C.2.1Profile testing summary for DECT NWK layer protocol.59C.2.2Profile testing summary for DECT DLC layer protocol.60C.2.3Profile testing summary for DECT MAC layer protocol.61C.2.4Profile testing summary for DECT PHL layer protocol.62C.2.5Profile testing summary for ISDN L2, L1 basic access protocol.63C.2.6Profile testing summary for DECT/ISDN IIP profile.64Annex D (normative):Profile eXtra Requirement List (XRL) proforma.65D.1Profile eXtra Requirement List for IIP - FT part.65D.1.1Parameters for IWU layer.65D.1.2Specific parameters for NWK layer.66D.1.3Specific parameters for DLC layer.67D.1.4Specific parameters for MAC layer.67SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)6Annex E (normative):Modifications of the DECT CI PCTR proforma.68E.1Modifications of DECT NWK layer PCTR proforma.68E.2Modifications of DECT DLC layer PCTR proforma.71E.3Modifications of DECT MAC layer PCTR proforma.74E.4Observations.76Annex F (normative):Abstract Test Suite (ATS) - NWK layer.77F.1The TTCN Graphical form (TTCN.GR).77F.2The TTCN Machine Processable form (TTCN.MP).77Annex G (normative):Abstract Test Suite (ATS) - DLC layer.78G.1The TTCN Graphical form (TTCN.GR).78G.2The TTCN Machine Processable form (TTCN.MP).78Annex H (normative):Abstract Test Suite (ATS) - MAC layer.79H.1The TTCN Graphical form (TTCN.GR).79H.2The TTCN Machine Processable form (TTCN.MP).79Annex J (normative):Abstract Test Suite (ATS) - Interworking Unit.80J.1The TTCN Graphical form (TTCN.GR).80J.2The TTCN Machine Processable form (TTCN.MP).80History.81SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)7Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respectof ETSI standards", which is available free of charge from the ETSI Secretariat. Latest updates are available on theETSI Web server (http://www.etsi.org/ipr).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)which are, or may be, or may become, essential to the present document.ForewordThis European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced CordlessTelecommunications (DECT).The present document is part 3 of a multi-part EN covering the DECT/ISDN interworking for intermediate systemconfiguration, as identified below:Part 1:"Profile Test Specification (PTS) summary";Part 2:"Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)".National transposition datesDate of adoption of this EN:25 December 1998Date of latest announcement of this EN (doa):31 March 1999Date of latest publication of new National Standardor endorsement of this EN (dop/e):30 September 1999Date of withdrawal of any conflicting National Standard (dow):30 September 1999SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)81ScopeThe present document contains the test specification for Digital Enhanced Cordless Telecommunications/IntegratedServices Digital Network (DECT/ISDN) Interworking for Intermediate system Profile (IIP) Fixed Part (FP) applicationsas specified in ETS 300 822 [6].This test specification provides conformance tests for DECT/ISDN terminal equipment conforming to ETS 300 822 [6].The main objective is to perform a high probability of inter-operability between the DECT/ISDN terminal equipmentand an ISDN network. The DECT/ISDN terminal equipment contains Fixed Parts (FPs) and Portable Parts (PPs) thatmay be supplied by different manufacturers.The ISO standard for the methodology of conformance testing ISO/IEC 9646 [19] to [25] is used as the basis for the testmethodology, and as the basis for test case specification.The test cases if listed in the present document have been derived from the corresponding ATS. Additional DECT/ISDNIIP specific test cases are included where required.Annex A provides Profile Implementation eXtra Information for Testing (IXIT) proforma part of the present document.Annex B provides Profile Conformance Test Report (Profile CTR) proforma part of the present document.Annex C provides System Conformance Test Report (SCTR) proforma part of the present document.Annex D provides the Profile X Requirement List (XRL) proforma part of the present document.Annex E provides modifications of DECT layer PCTR proforma of the present document.Annex F provides the Tree and Tabular Combined Notation (TTCN) part for DECT NWK layer conforming to therequirements of the present document.Annex G provides the TTCN part for DECT DLC layer conforming to the requirements of the present document.Annex H provides the TTCN part for DECT MAC layer conforming to the requirements of the present document.Annex I provides the TTCN part for DECT/ISDN IWU - IIP profile.2Normative referencesReferences may be made to:a)specific versions of publications (identified by date of publication, edition number, version number, etc.), inwhich case, subsequent revisions to the referenced document do not apply; orb)all versions up to and including the identified version (identified by "up to and including" before the versionidentity); orc)all versions subsequent to and including the identified version (identified by "onwards" following the versionidentity); ord)publications without mention of a specific version, in which case the latest version applies.A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the samenumber.[1]EN 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 2: Physical Layer (PHL)".[2]EN 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 3: Medium Access Control (MAC) layer".[3]EN 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 4: Data Link Control (DLC) layer".SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)9[4]EN 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI);Part 5: Network (NWK) layer".[5]EN 300 444 (1997): "Digital Enhanced Cordless Telecommunications (DECT); Generic AccessProfile (GAP)".[6]ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration;Interworking and profile specification".[7]EN 300 176: "Digital Enhanced Cordless Telecommunications (DECT); Approval testspecification".[8]ETS 300 476-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 4: Network (NWK)layer - Fixed radio Termination (FT)".[9]ETS 300 476-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 5: Data LinkControl (DLC) layer - Fixed radio Termination (FT)".[10]ETS 300 476-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 6: Medium AccessControl (MAC) layer - Fixed radio Termination (FT)".[11]ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer".[12]EN 301 241-2: "Digital Enhanced Cordless Telecommunications (DECT)/Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; ProfileImplementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)".[13]EN 300 497-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for MediumAccess Control (MAC) layer".[14]EN 300 497-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 3: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Fixed radio Termination (FT)".[15]EN 300 497-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - Data LinkControl (DLC) layer".[16]EN 300 497-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC) layer".[17]EN 300 497-8: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 8: Test Suite Structure (TSS) and Test Purposes (TP) - Network(NWK) layer - Fixed radio Termination (FT)".[18]EN 300 497-9: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 9: Abstract Test Suite (ATS) for Network (NWK) layer - Fixedradio Termination (FT)".[19]ISO/IEC 9646-1 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 1: General concepts". (See also CCITTRecommendation X.290 (1991)).[20]ISO/IEC 9646-2 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 2: Abstract Test Suite specification". (See also CCITTRecommendation X.291 (1991)).SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)10[21]ISO/IEC 9646-3 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 3: The Tree and Tabular Combined Notation". (See alsoCCITT Recommendation X.292 (1992)).[22]ISO/IEC 9646-4 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 4: Test realization". (See also CCITTRecommendation X.292 (1992)).[23]ISO/IEC 9646-5 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 5: Requirements on test laboratories and clients for theconformance assessment process". (See also CCITT Recommendation X.292 (1992)).[24]ISO/IEC 9646-6 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 6: Protocol profile test specification".[25]ISO/IEC 9646-7 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 7: Implementation Conformance Statement".[26]ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 2: General protocolspecification [ITU-T Recommendation Q.921 (1993), modified]".[27]ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 4: Protocol Implementation ConformanceStatement (PICS) proforma specification for the general protocol".[28]ETS 300 012 (1992) including Amendment 2 (1996): "Integrated Services Digital Network(ISDN); Basic user-network interface; Layer 1 specification and test principles".[29]Void.[30]TBR 3: "Integrated Services Digital Network (ISDN); Attachment requirements for terminalequipment to connect to an ISDN using ISDN basic access".[31]TBR 22: "Radio Equipment and Systems (RES); Attachment requirements for terminal equipmentfor Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP)applications".[32]EN 300 497-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Portable radio Termination (PT)".3Definitions and abbreviations3.1DefinitionsFor the purposes of the present document, the following terms and definitions apply:a)The terms defined in ISO/IEC 9646-7 [25]; andb)The definitions in ETS 300 822 [6].SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)113.2AbbreviationsFor the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 [19], ISO/IEC 9646-6 [24],ISO/IEC 9646-7 [25] and the abbreviations defined in ETS 300 822 [6], apply. In particular, the following abbreviationsapply:ASPAbstract Service PrimitiveATMAbstract Test MethodATSAbstract Test SuiteBIInvalid BehaviourBOInopportune BehaviourBVValid BehaviourCACapability testsCCCall Control entityCICommon InterfaceDECTDigital Enhanced Cordless TelecommunicationsDLCData Link Control layerFTFixed radio TerminationGAPGeneric Access ProfileICSImplementation Conformance StatementISDNIntegrated Services Digital NetworkISOInternational Organization for StandardizationIUTImplementation Under TestIXITImplementation eXtra Information for TestingIWPInterworking ProfileLCELink Control EntityLTLower TesterMACMedium Access Control layerMMMobility Management entityMTCMain Test ComponentNWKNetwork layerPDUProtocol Data UnitPHLPhysical layerPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPSTSProfile Specific Test SpecificationPTPortable radio TerminationPTSProfile Test SpecificationSAPService Access PointSCSSystem Conformance StatementSDUService Data UnitSUTSystem Under TestTPTest PurposeTSSTest Suite StructureXRLIXIT Requirements listSIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)124DECT NWK layer protocol4.1Additional test purposesFigure 1 shows the Network (NWK) Test Suite Structure (TSS) defined in EN 300 497-8 [17] for the conformancetesting.CCLCICCICRSCBVBIITBVBITIBVBVTIISMLLRLSRSBOTIBIBVMOBVLLLEAUPRKACACABOMMLOPMNWKMEBOOCITIDARCHFigure 1: NWK TSSNo test purpose for CC entity of the NWK layer as specified in EN 300 497-8 [17] applies without modification.Some of the test purposes for LCE entity of the NWK layer as specified in EN 300 497-8 [17] apply with nomodifications.No test purpose for CISS entity of the NWK layer is relevant.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)134.1.1Additional test purposes for IIP CC specific behaviours4.1.1.1Test group FT/CC/BV/ISTP_FT_CC_BV_IS_01ETS 300 822 [6], subclause 6.5Initial condition: CC is idle, no link is establishedCheck that, upon receipt of a correct {IWU_INFO} message containing a ISDN{SET-UP} requesting a U-plane, the IUT will reply by sending a {CC_SETUP} foran outgoing callTP_FT_CC_BV_IS_02ETS 300 822 [6], subclause 6.5Initial condition: CC is idle, no link is establishedCheck that, upon receipt of a {IWU_INFO} message containing an invalid ISDN{SET-UP}, the IUT will not reply by sending a {CC_SETUP} for an outgoing callTP_FT_CC_BV_IS_05ETS 300 822 [6], subclause 12.2.1Initial condition: a link is established, using a LU1 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU1 to LU7.TP_FT_CC_BV_IS_06ETS 300 822 [6], subclause 12.2.2Initial condition: a link is established, using a LU7 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU7 to LU1.TP_FT_CC_BV_IS_07ETS 300 822 [6], subclause 12.2.3Initial condition: a link is established, using a LU1 service U-planeCheck that the IUT after detecting the switching request (detecting the 2 100 Hzmodem tone over the U-plane link) starts the switching procedure from LU1 fullslot to LU8 double slot.TP_FT_CC_BV_IS_08ETS 300 822 [6], subclause 12.2.4Initial condition: a link is established, using a LU8 service U-planeCheck that the IUT after detecting the switching request starts the switchingprocedure from LU8 double slot to LU1 full slot.TP_FT_CC_BV_IS_09ETS 300 822 [6], subclause 12.2.4.1Initial condition: a link is established, using a LU7 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU7 to LU8.TP_FT_CC_BV_IS_10ETS 300 822 [6], subclause 12.2.4.1Initial condition: a link is established, using a LU8 service U-planeCheck that the IUT after detecting the switching request (evaluating ISDN layer3 messages) starts the switching procedure from LU8 to LU7.TP_FT_CC_BV_IS_11ETS 300 822 [6], subclause 6.7.3Initial condition: one link is established point to point configuration.Verify that the IUT, upon receipt of a DISCONNECT in the <> a{IWU-INFO}, initiates a disconnection from the network.4.2Abstract test methodAs stated in EN 300 497-9 [18], the ATM used for the DECT NWK layer is the remote embedded test method.The DECT/ISDN IIP implies no modification for the definition and the use of the ATM.4.3Relevant test casesThe test cases defined for the test group "FT/CC/BV/OC" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/IC" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/CI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/CR" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BV/RS" in EN 300 497-9 [18] are not relevant for the IIP profile.SIST EN 301 614-3:2000

ETSIEN 301 614-3 V1.1.2 (1999-02)14The test cases defined for the test group "FT/CC/BV/BO" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/BI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/CC/TI" in EN 300 497-9 [18] are not relevant for the IIP profile.The test cases defined for the test group "FT/MM/BV/ID" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:-TC-FT-MM-BV-ID-01.The test cases defined for the test group "FT/MM/BV/AU" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-AU-01, TC-FT-MM-BV-AU-04, TC-FT-MM-BV-AU-05, TC-FT-MM-BV-AU-06.The test cases defined for the test group "FT/MM/BV/LO" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-LO-01, TC-FT-MM-BV-LO-02, TC-FT-MM-BV-LO-03, TC-FT-MM-BV-LO-05,TC-FT-MM-BV-LO-06.The test cases defined for the test group "FT/MM/BV/AR" in EN 300 497-9 [18] relevant for the profile according totheir own selection rules are:TC-FT-MM-BV-AR-01, TC-FT-MM-BV-AR-03, TC-FT-MM-BV-AR-06.The test cases defined for the test group "FT/MM/BV/K
...