ETSI ETS 300 759 ed.1 (1997-10)

Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM

DE/DECT-060019

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Avtentikacijski modul (DAM) DECT - Preskušalna specifikacija za DAM

General Information

• Status: Published
• Publication Date: 07-Oct-1997
• Technical Committee: DECT 6 - Authentication module
• Current Stage: 12 - Completion
• Due Date: 24-Oct-1997
• Completion Date: 08-Oct-1997
• Mandate: T-306
• Ref Project: SIST ETS 300 759:2001 - Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 759 Edition 13SIST ETS 300 759:2001en01-IHEUXDU-20013SIST ETS 300 759:2001SLOVENSKI
STANDARD



SIST ETS 300 759:2001



EUROPEANETS 300 759TELECOMMUNICATIONOctober 1997STANDARDSource: DECTReference: DE/DECT-060019ICS:33.020Key words:DAM, DECT, radio, testingDigital Enhanced Cordless Telecommunications (DECT);DECT Authentication Module (DAM);Test specification for DAMETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: [e-mail].: [phone] - Fax: [phone]Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1997. All rights reserved.SIST ETS 300 759:2001



Page 2ETS 300 759: October 1997Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 759:2001



Page 3ETS 300 759: October 1997ContentsForeword.111Scope.132Normative references.133Definitions and abbreviations.133.1Definitions.133.2Abbreviations.144Test environment.144.1Test equipment.144.1.1PE simulator.144.1.2Signal generation device.144.1.3Precision force-inducing contacting device.144.1.4Temperature controllable environment.144.1.5Temperature measuring device.154.1.6Voltage Measuring Device.154.1.7Precision measuring device.154.1.8Current measuring device.154.2IUT default conditions.154.3Default data formatting.154.4Test procedure.154.5Test requirement.165Test group hierarchy.175.1Test groups under DAM.175.2Test groups under PHY.185.3Test groups under ELEC.185.4Test groups under LOG.195.5Test groups under SEC.195.6Test groups under CMD.205.7Test groups under CEF.206Test procedure.216.1Physical characteristics.216.1.1Format and layout.216.1.1.1ID-1 card.216.1.1.1.1Definition and applicability.216.1.1.1.2Conformance requirement.216.1.1.1.3Test purpose.226.1.1.1.4Method of test.226.1.1.1.5Test requirement.226.1.1.2Plug-in card.226.1.1.2.1Definition and applicability.226.1.1.2.2Conformance requirement.236.1.1.2.3Test purpose.236.1.1.2.4Method of test.236.1.1.2.5Test requirement.236.1.2Temperature range for card operation.246.1.2.1Definition and applicability.246.1.2.2Conformance requirement.246.1.2.3Test purpose.246.1.2.4Method of test.246.1.2.5Test requirement.256.1.3Contacts.256.1.3.1Definition and applicability.25SIST ETS 300 759:2001



Page 4ETS 300 759: October 19976.1.3.2Conformance requirement.256.1.3.3Test purpose.256.1.3.4Method of test.256.1.3.5Test requirement.256.2Electronic signals and transmission protocols.266.2.1Supply voltage Vcc (contact C1).266.2.1.1Voltage limits.266.2.1.1.1Definition and applicability.266.2.1.1.2Conformance requirement.266.2.1.1.3Test purpose.266.2.1.1.4Method of test.266.2.1.1.5Test requirement.276.2.1.2Current limits.276.2.1.2.1Definition and applicability.276.2.1.2.2Conformance requirement.276.2.1.2.3Test purpose.276.2.1.2.4Method of test.276.2.1.2.5Test requirement.286.2.1.3Idle current limits.286.2.1.3.1Definition and applicability.286.2.1.3.2Conformance requirement.286.2.1.3.3Test purpose.286.2.1.3.4Method of test.286.2.1.3.5Test requirement.296.2.1.4Current limits at all frequencies.296.2.1.4.1Definition and applicability.296.2.1.4.2Conformance requirement.296.2.1.4.3Test purpose.296.2.1.4.4Method of test.296.2.1.4.5Test requirement.296.2.2Reset RST (contact C2).306.2.2.1Static operation.306.2.2.1.1Definition and applicability.306.2.2.1.2Conformance requirement.306.2.2.1.3Test purpose.306.2.2.1.4Method of test.306.2.2.1.5Test requirement.316.2.2.2Dynamic operation.316.2.2.2.1Definition and applicability.316.2.2.2.2Conformance requirement.316.2.2.2.3Test purpose.316.2.2.2.4Method of test.316.2.2.2.5Test requirement.316.2.3Clock CLK (contact C3).326.2.3.1Frequency and duty cycle.326.2.3.1.1Definition and applicability.326.2.3.1.2Conformance requirement.326.2.3.1.3Test purpose.326.2.3.1.4Method of test.326.2.3.1.5Test requirement.336.2.3.2Voltage and current.336.2.3.2.1Definition and applicability.336.2.3.2.2Conformance requirement.336.2.3.2.3Test purpose.336.2.3.2.4Method of test.336.2.3.2.5Test requirement.346.2.3.3Dynamic operation.346.2.3.3.1Definition and applicability.346.2.3.3.2Conformance requirement.356.2.3.3.3Test purpose.356.2.3.3.4Method of test.356.2.3.3.5Test requirement.356.2.4I/O (contact C7).35SIST ETS 300 759:2001



Page 5ETS 300 759: October 19976.2.4.1Voltage and current.356.2.4.1.1Definition and applicability.356.2.4.1.2Conformance requirement.366.2.4.1.3Test purpose.366.2.4.1.4Method of test.366.2.4.1.5Test requirement.366.2.4.2Dynamic operation.366.2.4.2.1Definition and applicability.366.2.4.2.2Conformance requirement.376.2.4.2.3Test purpose.376.2.4.2.4Method of test.376.2.4.2.5Test requirement.376.2.5States.376.2.5.1Definition and applicability.376.2.5.2Conformance requirement.376.2.5.3Test purpose.386.2.5.4Method of test.386.2.5.5Test requirement.386.2.6Answer To Reset (ATR).386.2.6.1ATR content.386.2.6.1.1Definition and applicability.386.2.6.1.2Conformance requirement.396.2.6.1.3Test purpose.396.2.6.1.4Method of test.396.2.6.1.5Test requirement.406.2.6.2PTS procedure.406.2.6.2.1Definition and applicability.406.2.6.2.2Conformance requirement.406.2.6.2.3Test purpose.406.2.6.2.4Method of test.416.2.6.2.5Test requirement.416.2.7Major Capabilities.416.2.7.1Definition and applicability.416.2.7.2Conformance requirement.416.2.7.3Test purpose.416.2.7.4Method of test.426.2.7.5Test requirement.426.3Logical model.426.3.1File identifier.426.3.1.1File-type identification.426.3.1.1.1Definition and applicability.426.3.1.1.2Conformance requirement.426.3.1.1.3Test purpose.426.3.1.1.4Method of test.426.3.1.1.5Test requirement.436.3.1.2File ID assignments.436.3.1.2.1Definition and applicability.436.3.1.2.2Conformance requirement.436.3.1.2.3Test purpose.436.3.1.2.4Method of test.436.3.1.2.5Test requirement.436.3.2Dedicated files.446.3.2.1Definition and applicability.446.3.2.2Conformance requirement.446.3.2.3Test purpose.446.3.2.4Method of test.446.3.2.5Test requirement.456.3.3Elementary Files.456.3.3.1Definition and applicability.456.3.3.2Conformance requirement.456.3.3.3Test purpose.466.3.3.4Method of test.466.3.3.5Test requirement.46SIST ETS 300 759:2001



Page 6ETS 300 759: October 19976.3.4Methods for selecting the DECT application.466.3.4.1Definition and applicability.466.3.4.2Conformance requirement.476.3.4.3Test purpose.476.3.4.4Method of test.476.3.4.5Test requirement.476.3.5Methods for selecting a file.486.3.5.1Definition and applicability.486.3.5.2Conformance requirement.486.3.5.3Test purpose.486.3.5.4Method of test.496.3.5.5Test requirement.506.3.6Reservation of file IDs.506.3.6.1Definition and applicability.506.3.6.2Conformance requirement.506.3.6.3Test purpose.506.3.6.4Method of test.516.3.6.5Test requirement.516.4Security services and facilities.516.4.1Algorithms and processes.516.4.2Authentication.526.4.3UAK allocation.526.4.4File access control.526.4.4.1ALWAYS, CHV1, FT-AUT and NEVER.526.4.4.1.1Definition and applicability.526.4.4.1.2Conformance requirement.536.4.4.1.3Test purpose.536.4.4.1.4Method of test.536.4.4.1.5Test requirement.546.4.4.2CHV2.546.4.4.2.1Definition and applicability.546.4.4.2.2Conformance requirement.546.4.4.2.3Test purpose.546.4.4.2.4Method of test.556.4.4.2.5Test requirement.556.4.5Subscription registration maintenance.556.5Description of the functions.556.5.1SELECT function.556.5.1.1Definition and applicability.556.5.1.2Conformance requirement.566.5.1.3Test purpose.566.5.1.4Method of test.566.5.1.5Test requirement.576.5.2STATUS function.586.5.2.1Definition and applicability.586.5.2.2Conformance requirement.586.5.2.3Test purpose.586.5.2.4Method of test.596.5.2.5Test requirement.596.5.3READ BINARY function.596.5.3.1Definition and applicability.596.5.3.2Conformance requirement.606.5.3.3Test purpose.606.5.3.4Method of test.606.5.3.5Test requirement.616.5.4UPDATE BINARY function.616.5.4.1Definition and applicability.616.5.4.2Conformance requirement.616.5.4.3Test purpose.616.5.4.4Method of test.626.5.4.5Test requirement.626.5.5READ RECORD function.626.5.5.1Definition and applicability.62SIST ETS 300 759:2001



Page 7ETS 300 759: October 19976.5.5.2Conformance requirement.636.5.5.3Test purpose.636.5.5.4Method of test.646.5.5.5Test requirement.656.5.6UPDATE RECORD function.656.5.6.1Definition and applicability.656.5.6.2Conformance requirement.656.5.6.3Test purpose.666.5.6.4Method of test.666.5.6.5Test requirement.676.5.7SEEK function.686.5.7.1Definition and applicability.686.5.7.2Conformance requirement.686.5.7.3Test purpose.686.5.7.4Method of test.696.5.7.5Test requirement.706.5.8INCREASE function.706.5.8.1Definition and applicability.706.5.8.2Conformance requirement.716.5.8.3Test purpose.716.5.8.4Method of test.716.5.8.5Test requirement.716.5.9VERIFY CHV function.716.5.9.1Definition and applicability.716.5.9.2Conformance requirement.726.5.9.3Test purpose.726.5.9.4Method of test.726.5.9.5Test requirement.736.5.10CHANGE CHV function.736.5.10.1Definition and applicability.736.5.10.2Conformance requirement.746.5.10.3Test purpose.746.5.10.4Method of test.746.5.10.5Test requirement.756.5.11DISABLE CHV function.756.5.11.1Definition and applicability.756.5.11.2Conformance requirement.766.5.11.3Test purpose.766.5.11.4Method of test.766.5.11.5Test requirement.776.5.12ENABLE CHV function.776.5.12.1Definition and applicability.776.5.12.2Conformance requirement.776.5.12.3Test purpose.786.5.12.4Method of test.786.5.12.5Test requirement.796.5.13UNBLOCK CHV function.796.5.13.1Definition and applicability.796.5.13.2Conformance requirement.796.5.13.3Test purpose.796.5.13.4Method of test.806.5.13.5Test requirement.806.5.14INVALIDATE function.816.5.14.1Definition and applicability.816.5.14.2Conformance requirement.816.5.14.3Test purpose.816.5.14.4Method of test.816.5.14.5Test requirement.826.5.15REHABILITATE function.826.5.15.1Definition and applicability.826.5.15.2Conformance requirement.826.5.15.3Test purpose.826.5.15.4Method of test.83SIST ETS 300 759:2001



Page 8ETS 300 759: October 19976.5.15.5Test requirement.836.5.16ASK RANDOM function.836.5.16.1Definition and applicability.836.5.16.2Conformance requirement.846.5.16.3Test purpose.846.5.16.4Method of test.846.5.16.5Test requirement.846.5.17PT AUTHENTICATION function.846.5.17.1Definition and applicability.846.5.17.2Conformance requirement.856.5.17.3Test purpose.856.5.17.4Method of test.856.5.17.5Test requirement.866.5.18FT AUTHENTICATION function.866.5.18.1Definition and applicability.866.5.18.2Conformance requirement.876.5.18.3Test purpose.876.5.18.4Method of test.876.5.18
...

SLOVENSKI STANDARD
SIST ETS 300 759:2001
01-september-2001
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH'(&7$YWHQWLNDFLMVNLPRGXO
'$0'(&73UHVNXãDOQDVSHFLILNDFLMD]D'$0
Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module
(DAM); Test specification for DAM
Ta slovenski standard je istoveten z: ETS 300 759 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
SIST ETS 300 759:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 759:2001

---------------------- Page: 2 ----------------------

SIST ETS 300 759:2001
EUROPEAN ETS 300 759
TELECOMMUNICATION October 1997
STANDARD
Source: DECT Reference: DE/DECT-060019
ICS: 33.020
Key words: DAM, DECT, radio, testing
Digital Enhanced Cordless Telecommunications (DECT);
DECT Authentication Module (DAM);
Test specification for DAM
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: [e-mail]
Tel.: [phone] - Fax: [phone]
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1997. All rights reserved.

---------------------- Page: 3 ----------------------

SIST ETS 300 759:2001
Page 2
ETS 300 759: October 1997
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 759:2001
Page 3
ETS 300 759: October 1997
Contents
Foreword .11
1 Scope .13
2 Normative references.13
3 Definitions and abbreviations .13
3.1 Definitions .13
3.2 Abbreviations .14
4 Test environment .14
4.1 Test equipment .14
4.1.1 PE simulator.14
4.1.2 Signal generation device .14
4.1.3 Precision force-inducing contacting device .14
4.1.4 Temperature controllable environment .14
4.1.5 Temperature measuring device .15
4.1.6 Voltage Measuring Device .15
4.1.7 Precision measuring device .15
4.1.8 Current measuring device .15
4.2 IUT default conditions .15
4.3 Default data formatting .15
4.4 Test procedure.15
4.5 Test requirement.16
5 Test group hierarchy .17
5.1 Test groups under DAM.17
5.2 Test groups under PHY .18
5.3 Test groups under ELEC .18
5.4 Test groups under LOG.19
5.5 Test groups under SEC .19
5.6 Test groups under CMD .20
5.7 Test groups under CEF .20
6 Test procedure .21
6.1 Physical characteristics.21
6.1.1 Format and layout .21
6.1.1.1 ID-1 card.21
6.1.1.1.1 Definition and applicability.21
6.1.1.1.2 Conformance requirement.21
6.1.1.1.3 Test purpose.22
6.1.1.1.4 Method of test .22
6.1.1.1.5 Test requirement.22
6.1.1.2 Plug-in card.22
6.1.1.2.1 Definition and applicability.22
6.1.1.2.2 Conformance requirement.23
6.1.1.2.3 Test purpose.23
6.1.1.2.4 Method of test .23
6.1.1.2.5 Test requirement.23
6.1.2 Temperature range for card operation .24
6.1.2.1 Definition and applicability .24
6.1.2.2 Conformance requirement.24
6.1.2.3 Test purpose.24
6.1.2.4 Method of test.24
6.1.2.5 Test requirement .25
6.1.3 Contacts .25
6.1.3.1 Definition and applicability .25

---------------------- Page: 5 ----------------------

SIST ETS 300 759:2001
Page 4
ETS 300 759: October 1997
6.1.3.2 Conformance requirement . 25
6.1.3.3 Test purpose . 25
6.1.3.4 Method of test . 25
6.1.3.5 Test requirement. 25
6.2 Electronic signals and transmission protocols . 26
6.2.1 Supply voltage Vcc (contact C1). 26
6.2.1.1 Voltage limits. 26
6.2.1.1.1 Definition and applicability. 26
6.2.1.1.2 Conformance requirement . 26
6.2.1.1.3 Test purpose . 26
6.2.1.1.4 Method of test . 26
6.2.1.1.5 Test requirement. 27
6.2.1.2 Current limits. 27
6.2.1.2.1 Definition and applicability. 27
6.2.1.2.2 Conformance requirement . 27
6.2.1.2.3 Test purpose . 27
6.2.1.2.4 Method of test . 27
6.2.1.2.5 Test requirement. 28
6.2.1.3 Idle current limits. 28
6.2.1.3.1 Definition and applicability. 28
6.2.1.3.2 Conformance requirement . 28
6.2.1.3.3 Test purpose . 28
6.2.1.3.4 Method of test . 28
6.2.1.3.5 Test requirement. 29
6.2.1.4 Current limits at all frequencies. 29
6.2.1.4.1 Definition and applicability. 29
6.2.1.4.2 Conformance requirement . 29
6.2.1.4.3 Test purpose . 29
6.2.1.4.4 Method of test . 29
6.2.1.4.5 Test requirement. 29
6.2.2 Reset RST (contact C2) . 30
6.2.2.1 Static operation . 30
6.2.2.1.1 Definition and applicability. 30
6.2.2.1.2 Conformance requirement . 30
6.2.2.1.3 Test purpose . 30
6.2.2.1.4 Method of test . 30
6.2.2.1.5 Test requirement. 31
6.2.2.2 Dynamic operation . 31
6.2.2.2.1 Definition and applicability. 31
6.2.2.2.2 Conformance requirement . 31
6.2.2.2.3 Test purpose . 31
6.2.2.2.4 Method of test . 31
6.2.2.2.5 Test requirement. 31
6.2.3 Clock CLK (contact C3) . 32
6.2.3.1 Frequency and duty cycle . 32
6.2.3.1.1 Definition and applicability. 32
6.2.3.1.2 Conformance requirement . 32
6.2.3.1.3 Test purpose . 32
6.2.3.1.4 Method of test . 32
6.2.3.1.5 Test requirement. 33
6.2.3.2 Voltage and current. 33
6.2.3.2.1 Definition and applicability. 33
6.2.3.2.2 Conformance requirement . 33
6.2.3.2.3 Test purpose . 33
6.2.3.2.4 Method of test . 33
6.2.3.2.5 Test requirement. 34
6.2.3.3 Dynamic operation . 34
6.2.3.3.1 Definition and applicability. 34
6.2.3.3.2 Conformance requirement . 35
6.2.3.3.3 Test purpose . 35
6.2.3.3.4 Method of test . 35
6.2.3.3.5 Test requirement. 35
6.2.4 I/O (contact C7) . 35

---------------------- Page: 6 ----------------------

SIST ETS 300 759:2001
Page 5
ETS 300 759: October 1997
6.2.4.1 Voltage and current .35
6.2.4.1.1 Definition and applicability.35
6.2.4.1.2 Conformance requirement.36
6.2.4.1.3 Test purpose.36
6.2.4.1.4 Method of test .36
6.2.4.1.5 Test requirement.36
6.2.4.2 Dynamic operation.36
6.2.4.2.1 Definition and applicability.36
6.2.4.2.2 Conformance requirement.37
6.2.4.2.3 Test purpose.37
6.2.4.2.4 Method of test .37
6.2.4.2.5 Test requirement.37
6.2.5 States .37
6.2.5.1 Definition and applicability .37
6.2.5.2 Conformance requirement.37
6.2.5.3 Test purpose.38
6.2.5.4 Method of test.38
6.2.5.5 Test requirement .38
6.2.6 Answer To Reset (ATR) .38
6.2.6.1 ATR content.38
6.2.6.1.1 Definition and applicability.38
6.2.6.1.2 Conformance requirement.39
6.2.6.1.3 Test purpose.39
6.2.6.1.4 Method of test .39
6.2.6.1.5 Test requirement.40
6.2.6.2 PTS procedure .40
6.2.6.2.1 Definition and applicability.40
6.2.6.2.2 Conformance requirement.40
6.2.6.2.3 Test purpose.40
6.2.6.2.4 Method of test .41
6.2.6.2.5 Test requirement.41
6.2.7 Major Capabilities.41
6.2.7.1 Definition and applicability .41
6.2.7.2 Conformance requirement.41
6.2.7.3 Test purpose.41
6.2.7.4 Method of test.42
6.2.7.5 Test requirement .42
6.3 Logical model.42
6.3.1 File identifier .42
6.3.1.1 File-type identification .42
6.3.1.1.1 Definition and applicability.42
6.3.1.1.2 Conformance requirement.42
6.3.1.1.3 Test purpose.42
6.3.1.1.4 Method of test .42
6.3.1.1.5 Test requirement.43
6.3.1.2 File ID assignments .43
6.3.1.2.1 Definition and applicability.43
6.3.1.2.2 Conformance requirement.43
6.3.1.2.3 Test purpose.43
6.3.1.2.4 Method of test .43
6.3.1.2.5 Test requirement.43
6.3.2 Dedicated files.44
6.3.2.1 Definition and applicability .44
6.3.2.2 Conformance requirement.44
6.3.2.3 Test purpose.44
6.3.2.4 Method of test.44
6.3.2.5 Test requirement .45
6.3.3 Elementary Files.45
6.3.3.1 Definition and applicability .45
6.3.3.2 Conformance requirement.45
6.3.3.3 Test purpose.46
6.3.3.4 Method of test.46
6.3.3.5 Test requirement .46

---------------------- Page: 7 ----------------------

SIST ETS 300 759:2001
Page 6
ETS 300 759: October 1997
6.3.4 Methods for selecting the DECT application. 46
6.3.4.1 Definition and applicability. 46
6.3.4.2 Conformance requirement . 47
6.3.4.3 Test purpose . 47
6.3.4.4 Method of test . 47
6.3.4.5 Test requirement. 47
6.3.5 Methods for selecting a file. 48
6.3.5.1 Definition and applicability. 48
6.3.5.2 Conformance requirement . 48
6.3.5.3 Test purpose . 48
6.3.5.4 Method of test . 49
6.3.5.5 Test requirement. 50
6.3.6 Reservation of file IDs. 50
6.3.6.1 Definition and applicability. 50
6.3.6.2 Conformance requirement . 50
6.3.6.3 Test purpose . 50
6.3.6.4 Method of test . 51
6.3.6.5 Test requirement. 51
6.4 Security services and facilities . 51
6.4.1 Algorithms and processes . 51
6.4.2 Authentication . 52
6.4.3 UAK allocation . 52
6.4.4 File access control. 52
6.4.4.1 ALWAYS, CHV1, FT-AUT and NEVER . 52
6.4.4.1.1 Definition and applicability. 52
6.4.4.1.2 Conformance requirement . 53
6.4.4.1.3 Test purpose . 53
6.4.4.1.4 Method of test . 53
6.4.4.1.5 Test requirement. 54
6.4.4.2 CHV2. 54
6.4.4.2.1 Definition and applicability. 54
6.4.4.2.2 Conformance requirement . 54
6.4.4.2.3 Test purpose . 54
6.4.4.2.4 Method of test . 55
6.4.4.2.5 Test requirement. 55
6.4.5 Subscription registration maintenance. 55
6.5 Description of the functions. 55
6.5.1 SELECT function . 55
6.5.1.1 Definition and applicability. 55
6.5.1.2 Conformance requirement . 56
6.5.1.3 Test purpose . 56
6.5.1.4 Method of test . 56
6.5.1.5 Test requirement. 57
6.5.2 STATUS function. 58
6.5.2.1 Definition and applicability. 58
6.5.2.2 Conformance requirement . 58
6.5.2.3 Test purpose . 58
6.5.2.4 Method of test . 59
6.5.2.5 Test requirement. 59
6.5.3 READ BINARY function. 59
6.5.3.1 Definition and applicability. 59
6.5.3.2 Conformance requirement . 60
6.5.3.3 Test purpose . 60
6.5.3.4 Method of test . 60
6.5.3.5 Test requirement. 61
6.5.4 UPDATE BINARY function . 61
6.5.4.1 Definition and applicability. 61
6.5.4.2 Conformance requirement . 61
6.5.4.3 Test purpose . 61
6.5.4.4 Method of test . 62
6.5.4.5 Test requirement. 62
6.5.5 READ RECORD function. 62
6.5.5.1 Definition and applicability. 62

---------------------- Page: 8 ----------------------

SIST ETS 300 759:2001
Page 7
ETS 300 759: October 1997
6.5.5.2 Conformance requirement.63
6.5.5.3 Test purpose.63
6.5.5.4 Method of test.64
6.5.5.5 Test requirement .65
6.5.6 UPDATE RECORD function.65
6.5.6.1 Definition and applicability .65
6.5.6.2 Conformance requirement.65
6.5.6.3 Test purpose.66
6.5.6.4 Method of test.66
6.5.6.5 Test requirement .67
6.5.7 SEEK function .68
6.5.7.1 Definition and applicability .68
6.5.7.2 Conformance requirement.68
6.5.7.3 Test purpose.68
6.5.7.4 Method of test.69
6.5.7.5 Test requirement .70
6.5.8 INCREASE function .70
6.5.8.1 Definition and applicability .70
6.5.8.2 Conformance requirement.71
6.5.8.3 Test purpose.71
6.5.8.4 Method of test.71
6.5.8.5 Test requirement .71
6.5.9 VERIFY CHV function .71
6.5.9.1 Definition and applicability .71
6.5.9.2 Conformance requirement.72
6.5.9.3 Test purpose.72
6.5.9.4 Method of test.72
6.5.9.5 Test requirement .73
6.5.10 CHANGE CHV function.73
6.5.10.1 Definition and applicability .73
6.5.10.2 Conformance requirement.74
6.5.10.3 Test purpose.74
6.5.10.4 Method of test.74
6.5.10.5 Test requirement .75
6.5.11 DISABLE CHV function .75
6.5.11.1 Definition and applicability .75
6.5.11.2 Conformance requirement.76
6.5.11.3 Test purpose.76
6.5.11.4 Method of test.76
6.5.11.5 Test requirement .77
6.5.12 ENABLE CHV function .77
6.5.12.1 Definition and applicability .77
6.5.12.2 Conformance requirement.77
6.5.12.3 Test purpose.78
6.5.12.4 Method of test.78
6.5.12.5 Test requirement .79
6.5.13 UNBLOCK CHV function.79
6.5.13.1 Definition and applicability .79
6.5.13.2 Conformance requirement.79
6.5.13.3 Test purpose.79
6.5.13.4 Method of test.80
6.5.13.5 Test requirement .80
6.5.14 INVALIDATE function.81
6.5.14.1 Definition and applicability .81
6.5.14.2 Conformance requirement.81
6.5.14.3 Test purpose.81
6.5.14.4 Method of test.81
6.5.14.5 Test requirement .82
6.5.15 REHABILITATE function .82
6.5.15.1 Definition and applicability .82
6.5.15.2 Conformance requirement.82
6.5.15.3 Test purpose.82
6.5.15.4 Method of test.83

---------------------- Page: 9 ----------------------

SIST ETS 300 759:2001
Page 8
ETS 300 759: October 1997
6.5.15.5 T
...