ETSI EN 303 035-2 V1.2.1 (2001-12)
Terrestrial Trunked Radio (TETRA); Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive; Part 2: Direct Mode Operation (DMO)
Terrestrial Trunked Radio (TETRA); Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive; Part 2: Direct Mode Operation (DMO)
REN/TETRA-02044-2
Harmonizirani evropski standard (EN) za opremo TETRA, ki zajema bistvene zahteve člena 3.2 direktive o radijski in telekomunikacijski terminalski opremi (R&TTE) - 2. del: Neposredno obratovanje (DMO).
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LVWYHQHTerrestrial Trunked Radio (TETRA); Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive; Part 2: Direct Mode Operation (DMO)33.070.10Prizemni snopovni radio (TETRA)Terrestrial Trunked Radio (TETRA)ICS:Ta slovenski standard je istoveten z:EN 303 035-2 Version 1.2.136IST EN 303 035-2 V1.2.1:200en01-QRYHPEHU3SIST EN 303 035-2:200SLOVENSKI
STANDARD
SIST EN 303 035-2 V1.2.1:2003
ETSI EN 303 035-2 V1.2.1 (2001-12)Candidate Harmonized European Standard (Telecommunications series) Terrestrial Trunked Radio (TETRA);Harmonized EN for TETRA equipment covering essentialrequirements under article 3.2 of the R&TTE Directive;Part 2: Direct Mode Operation (DMO) SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 2
Reference REN/TETRA-02044-2 Keywords DMO, radio, regulation, TETRA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2001. All rights reserved.
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 3 Contents Intellectual Property Rights.6 Foreword.6 Introduction.7 1 Scope.9 2 References.10 3 Definitions and abbreviations.12 3.1 Definitions.12 3.2 Abbreviations.14 4 Technical requirements specifications.15 4.1 Environmental profile.15 4.2 Conformance requirements.15 4.2.1 Requirements associated with frequency and channel allocation.16 4.2.2 Requirements associated with transmitting functions.19 4.2.3 Requirements associated with receiving functions.23 4.2.4 Requirements associated with control and monitoring functions.24 4.2.4.1 Requirements for the radio layer.24 4.2.4.2 Requirements for the lower MAC layer.26 4.2.4.3 Managed DMO requirements.27 4.2.4.4 Requirements for the upper MAC layer.28 4.2.4.5 Requirements for the DMMM layer.32 4.2.4.6 Requirements for the DMCC layer.33 5 Testing for compliance with technical requirements.36 5.1 Environmental conditions for testing.36 5.2 Interpretation of the measurement results.36 5.3 Essential radio test suites.37 5.3.1 Reference test specifications.37 5.3.2 Test configuration.38 5.3.3 Test specification for DM-MS.39 5.3.3.1 Radio layer test specification for DM-MS.39 5.3.3.1.1 Test case index for radio layer for DM-MS.39 5.3.3.1.2 Test case selection expression definitions for radio layer for DM-MS.40 5.3.3.1.3 Test suite parameter definitions for radio layer for DM-MS.40 5.3.3.2 Managed DMO test specification for DM-MS.41 5.3.3.2.1 Test suite structure Managed DMO.41 5.3.3.2.2 Test case index for Managed DMO.41 5.3.3.2.3 Test case selection expression definitions for Managed DMO.41 5.3.3.2.4 Test suite parameter definitions for Managed DMO.42 5.3.3.3 Upper MAC layer test specification for DM-MS.42 5.3.3.3.1 Upper MAC layer test specification for DM-MS for operation MS to MS.42 5.3.3.3.2 Upper MAC layer test specification for DM-MS for operation with DMO Repeater type 1.44 5.3.3.3.3 Upper MAC layer test specification for DM-MS for operation with DMO Repeater type 2.47 5.3.3.3.4 Upper MAC layer test specification for DM-MS for operation with DMO Gateway.48 5.3.3.4 Direct Mode Mobility Management (DMMM) test specification for DM-MS for operation with DMO Gateway.50 5.3.3.4.1 Test suite structure for DMMM for MS-GW.50 5.3.3.4.2 Test case index for DMMM for DM-MS.50 5.3.3.4.3 Test case selection expression definitions DMMM for DM-MS.50 5.3.3.4.4 Test suite parameter definitions for DMMM for DM-MS.51 5.3.3.5 Direct Mode Call Control (DMCC) test specification for DM-MS.51 5.3.3.5.1 DMCC test specification for DM-MS for operation MS to MS.51 5.3.3.5.2 DMCC test specification for DM-MS for operation with DMO Repeater type 1.55 5.3.3.5.3 DMCC test specification for DM-MS for operation with DMO Repeater type 2.56 5.3.3.5.4 DMCC test specification for DM-MS for operation with DMO Gateway.58 SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 4 5.3.4 Test specification for DM-REP1.61 5.3.4.1 Radio layer test specification for DM-REP1.61 5.3.4.1.1 Test case index for radio layer for DM-REP1.61 5.3.4.1.2 Test case selection expression definitions for radio layer for DM-REP1.62 5.3.4.1.3 Test suite parameter definitions for radio layer for DM-REP1.63 5.3.4.2 Upper MAC layer test specification for DM-REP1.63 5.3.4.2.1 Test suite structure for Upper MAC layer for DM-REP1.63 5.3.4.2.2 Test case index for Upper MAC layer for DM-REP1.63 5.3.4.2.3 Test case selection expression definitions for Upper MAC layer for DM-REP1.64 5.3.4.2.4 Test suite parameter definitions for Upper MAC layer for DM-REP1.64 5.3.5 Test specification for DM-REP2.65 5.3.5.1 Radio layer test specification for DM-REP2.65 5.3.5.1.1 Test case index for radio layer for DM-REP2.65 5.3.5.1.2 Test case selection expression definitions for radio layer for DM-REP2.66 5.3.5.1.3 Test suite parameter definitions for radio layer for DM-REP2.67 5.3.5.2 Upper MAC layer test specification for DM-REP2.67 5.3.5.2.1 Test suite structure for Upper MAC layer for DM-REP2.67 5.3.5.2.2 Test case index for Upper MAC layer for DM-REP2.67 5.3.5.2.3 Test case selection expression definitions for Upper MAC layer for DM-REP2.68 5.3.5.2.4 Test suite parameter definitions for Upper MAC layer for DM-REP2.68 5.3.6 Test specification for DM-GATE.69 5.3.6.1 Radio layer test specification for DM-GATE.69 5.3.6.1.1 Test case index for radio layer for DM-GATE.69 5.3.6.1.2 Test case selection expression definitions for radio layer for DM-GATE.69 5.3.6.1.3 Test suite parameter definitions for radio layer for DM-GATE.69 Annex A (normative): The EN Requirements Table (EN-RT).70 A.1 General capabilities of equipment.71 A.1.1 Type of equipment.71 A.1.2 Modes of operation for DM-MS.71 A.1.3 Protocol layers.71 A.1.4 Services and capabilities.73 A.1.4.1 Services and capabilities for DM-MS.73 A.1.4.2 Services and capabilities for DM-REP1.75 A.1.4.3 Services and capabilities for DM-REP2.75 A.1.4.4 Services and capabilities for DM-GATE.75 A.1.5 Environmental profile.76 A.2 Radio layer requirements.76 A.2.1 Radio layer requirements associated with frequency and channel allocation.76 A.2.2 Radio layer requirements associated with transmitting functions.79 A.2.3 Radio layer requirements associated with receiving functions.81 A.2.4 Radio layer requirements associated with control and monitoring functions.82 A.3 Medium Access Control (MAC) layer requirements.83 A.3.1 Lower MAC.83 A.3.2 Managed DMO.84 A.3.3 Upper MAC.84 A.3.3.1 Upper MAC for DM-MS.84 A.3.3.2 Upper MAC for DM-REP1.87 A.3.3.3 Upper MAC for DM-REP2.89 A.3.3.4 Upper MAC for DM-GATE.90 A.4 Direct Mode Mobility Management (DMMM) requirements.91 A.5 Direct Mode Call Control (DMCC) requirements.92 A.5.1 DMCC for DM-MS.92 A.5.2 DMCC for DM-GATE.95 Annex B (normative): Declarations on capabilities and parameters supported.98 B.1 Radio layer.98 B.2 Managed Direct Mode Operation (M-DMO).99 SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 5 B.3 Medium Access Control (MAC).99 B.3.1 Upper MAC for DM-MS.99 B.3.1.1 Upper MAC for DM-MS for operation MS to MS.99 B.3.1.2 Upper MAC for DM-MS for operation with DMO Repeater type 1.100 B.3.1.3 Upper MAC for DM-MS for operation with DMO Repeater type 2.100 B.3.1.4 Upper MAC for DM-MS for operation with DMO Gateway.101 B.3.2 Upper MAC for DMO Repeater type 1.102 B.3.3 Upper MAC for DMO Repeater type 2.102 B.4 Direct Mode Mobility Management (DMMM).102 B.5 Direct Mode Call Control (DMCC).103 B.5.1 DMCC for DM-MS for operation MS to MS.103 B.5.2 DMCC for DM-MS for operation with DMO Repeater type 1.103 B.5.3 DMCC for DM-MS for operation with DMO Repeater type 2.104 B.5.4 DMCC for DM-MS for operation with DMO Gateway.104 Annex C (normative): Test Specification for Managed DMO.106 C.1 Introduction.106 C.2 Test Suite Structure and Test Purposes (TSS&TP).106 C.2.1 Test Suite Structure (TSS).106 C.2.2 Test purposes.106 C.2.2.1 M-DMO-MS MAC (M_DMO_MSMS_MAC) tests.106 C.2.2.1.1 M-DMO-MS MAC capability tests.106 C.3 Abstract Test Specification for Managed DMO.107 C.3.1 Abstract Test Method (ATM) for Managed DMO.107 C.3.2 Abstract Test Suite (ATS) for Managed DMO.107 C.3.2.1 The TTCN Graphical form (TTCN.GR).107 C.3.2.2 The TTCN Machine Processable form (TTCN.MP).107 Annex D (informative): The EN title in the official languages.108 Annex E (informative): Justifications for requirements.109 Annex F (informative): Bibliography.110 History.111
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive") [1]. Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A. The present document is part 2 of a multi-part deliverable covering Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive, as identified below: Part 1: "Voice plus Data (V+D)"; Part 2: "Direct Mode Operation (DMO)".
National transposition dates Date of adoption of this EN: 14 December 2001 Date of latest announcement of this EN (doa): 31 March 2002 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 September 2002 Date of withdrawal of any conflicting National Standard (dow): 30 September 2003
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 7 Introduction The present document is part of a set of standards designed to fit in a modular structure to cover all radio and telecommunications terminal equipment under the R&TTE Directive [1]. Each standard is a module in the structure. The modular structure is shown in figure 1.
- If needed, new standards for human exposure to Electromagnetic Fields, - if needed, new standards for acoustic safety Use of spectrum * If needed Scoped by
equipment
class or type Scoped by frequency and/or equipment type Disability* Privacy* Fraud* No harm to the network* Emergency* Interworking via
the network* Interworking with the network* Non-radio Radio (RE) Non-TTE TTE 3.1b 3.2 3.3c 3.3b 3.3a 3.3d 3.3e 3.3f Radio Product EMC EN 301 489 multi-part EMC standar Generic and product standards also notified under EMC Directive Standards also notified under LV Directive 3.1a New radio harmonized standards Spectrum EMC Safety
Figure 1: Modular structure for the various standards used under the R&TTE Directive SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 8 The left hand edge of the figure shows the different clauses of article 3 of the R&TTE Directive [1]. For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present document essential requirements in these areas have to be adopted by the Commission. If such essential requirements are adopted, and as far and as long as they are applicable, they will justify individual standards whose scope is likely to be specified by function or interface type. The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The scopes of these standards are specified either by frequency (normally in the case where frequency bands are harmonized) or by radio equipment type. For article 3.1b the diagram shows EN 301 489, the multi-part product EMC standard for radio used under the EMC Directive [2].
For article 3.1a the diagram shows the existing safety standards currently used under the LV Directive [3] and new standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be required. The bottom of the figure shows the relationship of the standards to radio equipment and telecommunications terminal equipment. A particular equipment may be radio equipment, telecommunications terminal equipment or both. A radio spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant essential requirement under the R&TTE Directive [1] is adopted by the Commission and if the equipment in question is covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential requirements under the R&TTE Directive [1] may be covered in a set of standards. The modularity principle has been taken because: - it minimizes the number of standards needed. Because equipment may, in fact, have multiple interfaces and functions it is not practicable to produce a single standard for each possible combination of functions that may occur in an equipment; - it provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published; - it clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 9 1 Scope The present document specifies the technical characteristics to be provided by Terrestrial Trunked Radio (TETRA) radio and telecommunications terminal equipment, which uses the TETRA technology for Direct Mode Operation at the air interface to support the Direct Mode Operation (DMO) functionality.
The present document applies at the TETRA Direct Mode Operation (DMO) Air interface of the following radio and telecommunications terminal equipment types: 1) TETRA Direct Mode Mobile Station (DM-MS); 2) TETRA Direct Mode Gateway (DM-GATE); 3) TETRA Direct Mode Repeater type 1 (DM-REP1); 4) TETRA Direct Mode Repeater type 2 (DM-REP2). In addition to the basic technical characteristics of a DM-MS required for operation with another DM-MS (MS-MS), the technical characteristics for operation with DM-GATE (MS-GW), DM-REP1 (MS-REP1) and DM-REP2 (MS-REP2) are specified. It applies to terminal equipment operating within the frequency ranges, allocated to TETRA by the ERC Decisions ERC/DEC(96)01 [30] and ERC/DEC(96)04 [31]. These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. Table 1: Radiocommunications service frequency bands Type of Service Radiocommunications service frequency bands (MHz) Emergency Access, ERC/DEC(96)01 [30] 380 to 385
Emergency Access, ERC/DEC(96)01 [30] 390 to 395 Civil Access, ERC/DEC(96)04 [31] 410 to 430 Civil Access, ERC/DEC(96)04 [31] 870 to 876
Civil Access, ERC/DEC(96)04 [31] 915 to 921 Civil Access, ERC/DEC(96)04 [31] 450 to 470 Civil Access, ERC/DEC(96)04 [31] 385 to 390 Civil Access, ERC/DEC(96)04 [31] 395 to 399,99
The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1], article 3.2, which states that ". radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful inter
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LVWYHQHTerrestrial Trunked Radio (TETRA); Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive; Part 2: Direct Mode Operation (DMO)33.070.10Prizemni snopovni radio (TETRA)Terrestrial Trunked Radio (TETRA)ICS:Ta slovenski standard je istoveten z:EN 303 035-2 Version 1.2.1SIST EN 303 035-2 V1.2.1:2003en01-marec-2003SIST EN 303 035-2 V1.2.1:2003SLOVENSKI
STANDARD
SIST EN 303 035-2 V1.2.1:2003
ETSI EN 303 035-2 V1.2.1 (2001-12)Candidate Harmonized European Standard (Telecommunications series) Terrestrial Trunked Radio (TETRA);Harmonized EN for TETRA equipment covering essentialrequirements under article 3.2 of the R&TTE Directive;Part 2: Direct Mode Operation (DMO) SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 2
Reference REN/TETRA-02044-2 Keywords DMO, radio, regulation, TETRA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2001. All rights reserved.
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 3 Contents Intellectual Property Rights.6 Foreword.6 Introduction.7 1 Scope.9 2 References.10 3 Definitions and abbreviations.12 3.1 Definitions.12 3.2 Abbreviations.14 4 Technical requirements specifications.15 4.1 Environmental profile.15 4.2 Conformance requirements.15 4.2.1 Requirements associated with frequency and channel allocation.16 4.2.2 Requirements associated with transmitting functions.19 4.2.3 Requirements associated with receiving functions.23 4.2.4 Requirements associated with control and monitoring functions.24 4.2.4.1 Requirements for the radio layer.24 4.2.4.2 Requirements for the lower MAC layer.26 4.2.4.3 Managed DMO requirements.27 4.2.4.4 Requirements for the upper MAC layer.28 4.2.4.5 Requirements for the DMMM layer.32 4.2.4.6 Requirements for the DMCC layer.33 5 Testing for compliance with technical requirements.36 5.1 Environmental conditions for testing.36 5.2 Interpretation of the measurement results.36 5.3 Essential radio test suites.37 5.3.1 Reference test specifications.37 5.3.2 Test configuration.38 5.3.3 Test specification for DM-MS.39 5.3.3.1 Radio layer test specification for DM-MS.39 5.3.3.1.1 Test case index for radio layer for DM-MS.39 5.3.3.1.2 Test case selection expression definitions for radio layer for DM-MS.40 5.3.3.1.3 Test suite parameter definitions for radio layer for DM-MS.40 5.3.3.2 Managed DMO test specification for DM-MS.41 5.3.3.2.1 Test suite structure Managed DMO.41 5.3.3.2.2 Test case index for Managed DMO.41 5.3.3.2.3 Test case selection expression definitions for Managed DMO.41 5.3.3.2.4 Test suite parameter definitions for Managed DMO.42 5.3.3.3 Upper MAC layer test specification for DM-MS.42 5.3.3.3.1 Upper MAC layer test specification for DM-MS for operation MS to MS.42 5.3.3.3.2 Upper MAC layer test specification for DM-MS for operation with DMO Repeater type 1.44 5.3.3.3.3 Upper MAC layer test specification for DM-MS for operation with DMO Repeater type 2.47 5.3.3.3.4 Upper MAC layer test specification for DM-MS for operation with DMO Gateway.48 5.3.3.4 Direct Mode Mobility Management (DMMM) test specification for DM-MS for operation with DMO Gateway.50 5.3.3.4.1 Test suite structure for DMMM for MS-GW.50 5.3.3.4.2 Test case index for DMMM for DM-MS.50 5.3.3.4.3 Test case selection expression definitions DMMM for DM-MS.50 5.3.3.4.4 Test suite parameter definitions for DMMM for DM-MS.51 5.3.3.5 Direct Mode Call Control (DMCC) test specification for DM-MS.51 5.3.3.5.1 DMCC test specification for DM-MS for operation MS to MS.51 5.3.3.5.2 DMCC test specification for DM-MS for operation with DMO Repeater type 1.55 5.3.3.5.3 DMCC test specification for DM-MS for operation with DMO Repeater type 2.56 5.3.3.5.4 DMCC test specification for DM-MS for operation with DMO Gateway.58 SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 4 5.3.4 Test specification for DM-REP1.61 5.3.4.1 Radio layer test specification for DM-REP1.61 5.3.4.1.1 Test case index for radio layer for DM-REP1.61 5.3.4.1.2 Test case selection expression definitions for radio layer for DM-REP1.62 5.3.4.1.3 Test suite parameter definitions for radio layer for DM-REP1.63 5.3.4.2 Upper MAC layer test specification for DM-REP1.63 5.3.4.2.1 Test suite structure for Upper MAC layer for DM-REP1.63 5.3.4.2.2 Test case index for Upper MAC layer for DM-REP1.63 5.3.4.2.3 Test case selection expression definitions for Upper MAC layer for DM-REP1.64 5.3.4.2.4 Test suite parameter definitions for Upper MAC layer for DM-REP1.64 5.3.5 Test specification for DM-REP2.65 5.3.5.1 Radio layer test specification for DM-REP2.65 5.3.5.1.1 Test case index for radio layer for DM-REP2.65 5.3.5.1.2 Test case selection expression definitions for radio layer for DM-REP2.66 5.3.5.1.3 Test suite parameter definitions for radio layer for DM-REP2.67 5.3.5.2 Upper MAC layer test specification for DM-REP2.67 5.3.5.2.1 Test suite structure for Upper MAC layer for DM-REP2.67 5.3.5.2.2 Test case index for Upper MAC layer for DM-REP2.67 5.3.5.2.3 Test case selection expression definitions for Upper MAC layer for DM-REP2.68 5.3.5.2.4 Test suite parameter definitions for Upper MAC layer for DM-REP2.68 5.3.6 Test specification for DM-GATE.69 5.3.6.1 Radio layer test specification for DM-GATE.69 5.3.6.1.1 Test case index for radio layer for DM-GATE.69 5.3.6.1.2 Test case selection expression definitions for radio layer for DM-GATE.69 5.3.6.1.3 Test suite parameter definitions for radio layer for DM-GATE.69 Annex A (normative): The EN Requirements Table (EN-RT).70 A.1 General capabilities of equipment.71 A.1.1 Type of equipment.71 A.1.2 Modes of operation for DM-MS.71 A.1.3 Protocol layers.71 A.1.4 Services and capabilities.73 A.1.4.1 Services and capabilities for DM-MS.73 A.1.4.2 Services and capabilities for DM-REP1.75 A.1.4.3 Services and capabilities for DM-REP2.75 A.1.4.4 Services and capabilities for DM-GATE.75 A.1.5 Environmental profile.76 A.2 Radio layer requirements.76 A.2.1 Radio layer requirements associated with frequency and channel allocation.76 A.2.2 Radio layer requirements associated with transmitting functions.79 A.2.3 Radio layer requirements associated with receiving functions.81 A.2.4 Radio layer requirements associated with control and monitoring functions.82 A.3 Medium Access Control (MAC) layer requirements.83 A.3.1 Lower MAC.83 A.3.2 Managed DMO.84 A.3.3 Upper MAC.84 A.3.3.1 Upper MAC for DM-MS.84 A.3.3.2 Upper MAC for DM-REP1.87 A.3.3.3 Upper MAC for DM-REP2.89 A.3.3.4 Upper MAC for DM-GATE.90 A.4 Direct Mode Mobility Management (DMMM) requirements.91 A.5 Direct Mode Call Control (DMCC) requirements.92 A.5.1 DMCC for DM-MS.92 A.5.2 DMCC for DM-GATE.95 Annex B (normative): Declarations on capabilities and parameters supported.98 B.1 Radio layer.98 B.2 Managed Direct Mode Operation (M-DMO).99 SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 5 B.3 Medium Access Control (MAC).99 B.3.1 Upper MAC for DM-MS.99 B.3.1.1 Upper MAC for DM-MS for operation MS to MS.99 B.3.1.2 Upper MAC for DM-MS for operation with DMO Repeater type 1.100 B.3.1.3 Upper MAC for DM-MS for operation with DMO Repeater type 2.100 B.3.1.4 Upper MAC for DM-MS for operation with DMO Gateway.101 B.3.2 Upper MAC for DMO Repeater type 1.102 B.3.3 Upper MAC for DMO Repeater type 2.102 B.4 Direct Mode Mobility Management (DMMM).102 B.5 Direct Mode Call Control (DMCC).103 B.5.1 DMCC for DM-MS for operation MS to MS.103 B.5.2 DMCC for DM-MS for operation with DMO Repeater type 1.103 B.5.3 DMCC for DM-MS for operation with DMO Repeater type 2.104 B.5.4 DMCC for DM-MS for operation with DMO Gateway.104 Annex C (normative): Test Specification for Managed DMO.106 C.1 Introduction.106 C.2 Test Suite Structure and Test Purposes (TSS&TP).106 C.2.1 Test Suite Structure (TSS).106 C.2.2 Test purposes.106 C.2.2.1 M-DMO-MS MAC (M_DMO_MSMS_MAC) tests.106 C.2.2.1.1 M-DMO-MS MAC capability tests.106 C.3 Abstract Test Specification for Managed DMO.107 C.3.1 Abstract Test Method (ATM) for Managed DMO.107 C.3.2 Abstract Test Suite (ATS) for Managed DMO.107 C.3.2.1 The TTCN Graphical form (TTCN.GR).107 C.3.2.2 The TTCN Machine Processable form (TTCN.MP).107 Annex D (informative): The EN title in the official languages.108 Annex E (informative): Justifications for requirements.109 Annex F (informative): Bibliography.110 History.111
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive") [1]. Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A. The present document is part 2 of a multi-part deliverable covering Harmonized EN for TETRA equipment covering essential requirements under article 3.2 of the R&TTE Directive, as identified below: Part 1: "Voice plus Data (V+D)"; Part 2: "Direct Mode Operation (DMO)".
National transposition dates Date of adoption of this EN: 14 December 2001 Date of latest announcement of this EN (doa): 31 March 2002 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 September 2002 Date of withdrawal of any conflicting National Standard (dow): 30 September 2003
SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 7 Introduction The present document is part of a set of standards designed to fit in a modular structure to cover all radio and telecommunications terminal equipment under the R&TTE Directive [1]. Each standard is a module in the structure. The modular structure is shown in figure 1.
- If needed, new standards for human exposure to Electromagnetic Fields, - if needed, new standards for acoustic safety Use of spectrum * If needed Scoped by
equipment
class or type Scoped by frequency and/or equipment type Disability* Privacy* Fraud* No harm to the network* Emergency* Interworking via
the network* Interworking with the network* Non-radio Radio (RE) Non-TTE TTE 3.1b 3.2 3.3c 3.3b 3.3a 3.3d 3.3e 3.3f Radio Product EMC EN 301 489 multi-part EMC standar Generic and product standards also notified under EMC Directive Standards also notified under LV Directive 3.1a New radio harmonized standards Spectrum EMC Safety
Figure 1: Modular structure for the various standards used under the R&TTE Directive SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 8 The left hand edge of the figure shows the different clauses of article 3 of the R&TTE Directive [1]. For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present document essential requirements in these areas have to be adopted by the Commission. If such essential requirements are adopted, and as far and as long as they are applicable, they will justify individual standards whose scope is likely to be specified by function or interface type. The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The scopes of these standards are specified either by frequency (normally in the case where frequency bands are harmonized) or by radio equipment type. For article 3.1b the diagram shows EN 301 489, the multi-part product EMC standard for radio used under the EMC Directive [2].
For article 3.1a the diagram shows the existing safety standards currently used under the LV Directive [3] and new standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be required. The bottom of the figure shows the relationship of the standards to radio equipment and telecommunications terminal equipment. A particular equipment may be radio equipment, telecommunications terminal equipment or both. A radio spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant essential requirement under the R&TTE Directive [1] is adopted by the Commission and if the equipment in question is covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential requirements under the R&TTE Directive [1] may be covered in a set of standards. The modularity principle has been taken because: - it minimizes the number of standards needed. Because equipment may, in fact, have multiple interfaces and functions it is not practicable to produce a single standard for each possible combination of functions that may occur in an equipment; - it provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published; - it clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. SIST EN 303 035-2 V1.2.1:2003
ETSI ETSI EN 303 035-2 V1.2.1 (2001-12) 9 1 Scope The present document specifies the technical characteristics to be provided by Terrestrial Trunked Radio (TETRA) radio and telecommunications terminal equipment, which uses the TETRA technology for Direct Mode Operation at the air interface to support the Direct Mode Operation (DMO) functionality.
The present document applies at the TETRA Direct Mode Operation (DMO) Air interface of the following radio and telecommunications terminal equipment types: 1) TETRA Direct Mode Mobile Station (DM-MS); 2) TETRA Direct Mode Gateway (DM-GATE); 3) TETRA Direct Mode Repeater type 1 (DM-REP1); 4) TETRA Direct Mode Repeater type 2 (DM-REP2). In addition to the basic technical characteristics of a DM-MS required for operation with another DM-MS (MS-MS), the technical characteristics for operation with DM-GATE (MS-GW), DM-REP1 (MS-REP1) and DM-REP2 (MS-REP2) are specified. It applies to terminal equipment operating within the frequency ranges, allocated to TETRA by the ERC Decisions ERC/DEC(96)01 [30] and ERC/DEC(96)04 [31]. These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. Table 1: Radiocommunications service frequency bands Type of Service Radiocommunications service frequency bands (MHz) Emergency Access, ERC/DEC(96)01 [30] 380 to 385
Emergency Access, ERC/DEC(96)01 [30] 390 to 395 Civil Access, ERC/DEC(96)04 [31] 410 to 430 Civil Access, ERC/DEC(96)04 [31] 870 to 876
Civil Access, ERC/DEC(96)04 [31] 915 to 921 Civil Access, ERC/DEC(96)04 [31] 450 to 470 Civil Access, ERC/DEC(96)04 [31] 385 to 390 Civil Access, ERC/DEC(96)04 [31] 395 to 399,99
The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1], article 3.2, which states that ". radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.