ETSI EN 301 502 V9.2.0 (2010-08)
Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive
Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive
REN/MSG-00005
Globalni sistem mobilnih komunikacij (GSM) - Harmonizirani EN za opremo za bazne postaje, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Pričujoči dokument velja za naslednje tipe {radijske} {telekomunikacijsko terminalne} opreme: GSM bazne postaje.
Pričujoči dokument je namenjen, da zajema določbe Direktive 1999/5/EC (direktive R&TTE)[i.2], člena 3.2, ki navaja, da »… radijska oprema je narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.« Glede na motnje sistemov, ki delujejo v sosednjih pasovih, je zagotovljeno vodenje za enojni BTS nosilec in večkratni BTS nosilec v Poročilu ECC 146 [i.4]. Poleg pričujočega dokumenta se drugi EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2], lahko uporabljajo za opremo znotraj področja uporabe pričujočega dokumenta.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.7(Global System for Mobile communications (GSM) - Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive33.070.50Globalni sistem za mobilno telekomunikacijo (GSM)Global System for Mobile Communication (GSM)ICS:Ta slovenski standard je istoveten z:EN 301 502 Version 9.2.1SIST EN 301 502 V9.2.1:2010en01-december-2010SIST EN 301 502 V9.2.1:2010SLOVENSKI
STANDARD
SIST EN 301 502 V9.2.1:2010
ETSI EN 301 502 V9.2.1 (2010-10)Harmonized European Standard (Telecommunications series) Global System for Mobile communications (GSM);Harmonized EN for Base Station Equipmentcovering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 502 V9.2.1:2010
ETSI ETSI EN 301 502 V9.2.1 (2010-10) 2
Reference REN/MSG-00005 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 502 V9.2.1:2010
ETSI ETSI EN 301 502 V9.2.1 (2010-10) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 10 3 Definitions and abbreviations . 10 3.1 Definitions . 10 3.2 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Environmental profile . 13 4.2 Conformance requirements . 13 4.2.1 Modulation accuracy. 14 4.2.1.1 Definition . 14 4.2.1.2 Limit . 14 4.2.1.3 Conformance . 15 4.2.2 Mean transmitted RF carrier power . 15 4.2.2.1 Definition . 15 4.2.2.2 Limit . 15 4.2.2.3 Conformance . 16 4.2.3 Transmitted RF carrier power versus time . 16 4.2.3.1 Definition . 16 4.2.3.2 Limit . 16 4.2.3.3 Conformance . 19 4.2.4 Adjacent channel power . 19 4.2.4.1 Spectrum due to modulation and wideband noise . 20 4.2.4.1.1 Definition. 20 4.2.4.1.2 Limit . 20 4.2.4.1.3 Conformance . 22 4.2.4.2 Switching transients spectrum . 22 4.2.4.2.1 Definition. 22 4.2.4.2.2 Limit . 22 4.2.4.2.3 Conformance . 22 4.2.5 Spurious emissions from the transmitter antenna connector . 22 4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 22 4.2.5.1.1 Definition. 22 4.2.5.1.2 Limit . 22 4.2.5.1.3 Conformance . 22 4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 22 4.2.5.2.1 Definition. 23 4.2.5.2.2 Limit . 23 4.2.5.2.3 Conformance . 24 4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 24 4.2.5.3.1 Definition. 24 4.2.5.3.2 Limit . 24 4.2.5.3.3 Conformance . 24 4.2.6 Intermodulation attenuation . 24 4.2.6.1 Definition . 24 4.2.6.2 Limit . 24 SIST EN 301 502 V9.2.1:2010
ETSI ETSI EN 301 502 V9.2.1 (2010-10) 4 4.2.6.2.1 For all BTSs except multicarrier BTS . 24 4.2.6.2.2 For multicarrier BTS . 25 4.2.6.3 Conformance . 25 4.2.7 Intra Base Station System intermodulation attenuation . 25 4.2.7.1 Definition . 25 4.2.7.2 Limit . 25 4.2.7.2.1 For all BTSs except multicarrier BTS . 25 4.2.7.2.2 For multicarrier BTS . 25 4.2.7.3 Conformance . 25 4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 25 4.2.8.1 Definition . 25 4.2.8.2 Limit . 26 4.2.9 Static Reference Sensitivity Level . 27 4.2.9.1 Definition . 27 4.2.9.2 Limit . 27 4.2.9.3 Conformance . 30 4.2.10 Multipath Reference Sensitivity Level . 30 4.2.10.1 Definition . 30 4.2.10.2 Limit . 30 4.2.10.3 Conformance . 37 4.2.11 Reference Interference Level . 37 4.2.11.1 Definition . 37 4.2.11.2 Limit . 38 4.2.11.3 Conformance . 51 4.2.12 Blocking Characteristics . 51 4.2.12.1 Definition . 51 4.2.12.2 Limit . 51 4.2.12.2.1 Blocking . 51 4.2.12.2.2 Spurious response . 52 4.2.12.3 Conformance . 52 4.2.13 Intermodulation characteristics . 52 4.2.13.1 Definition . 52 4.2.13.2 Limit . 53 4.2.13.3 Conformance . 53 4.2.14 AM suppression . 53 4.2.14.1 Definition . 53 4.2.14.2 Limit . 53 4.2.14.3 Conformance . 53 4.2.15 Spurious emissions from the receiver antenna connector . 53 4.2.15.1 Definition . 53 4.2.15.2 Limit . 54 4.2.15.3 Conformance . 54 4.2.16 Radiated spurious emissions . 54 4.2.16.1 Definition . 54 4.2.16.2 Limit . 54 4.2.16.3 Conformance . 54 5 Testing for compliance with technical requirements . 54 5.1 Environmental conditions for testing . 54 5.2 Interpretation of the measurement results . 55 5.3 Essential radio test suites . 56 5.3.1 Modulation accuracy. 56 5.3.1.1 Test case . 56 5.3.1.2 Test Environment . 57 5.3.2 Mean transmitted RF carrier power . 57 5.3.2.1 Test case . 57 5.3.2.2 Test Environment . 58 5.3.3 Transmitted RF carrier power versus time . 58 5.3.3.1 Test case . 58 5.3.3.2 Test Environment . 59 5.3.4 Adjacent channel power . 59 5.3.4.1 Spectrum due to modulation and wideband noise . 59 SIST EN 301 502 V9.2.1:2010
ETSI ETSI EN 301 502 V9.2.1 (2010-10) 5 5.3.4.1.1 Test case . 59 5.3.4.1.2 Test Environment . 60 5.3.4.2 Switching transients spectrum . 60 5.3.4.2.1 Test case . 60 5.3.4.2.2 Test Environment . 61 5.3.5 Spurious emissions from the transmitter antenna connector . 62 5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 62 5.3.5.1.1 Test case . 62 5.3.5.1.2 Test Environment . 62 5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 62 5.3.5.2.1 All base stations except multicarrier BTS . 62 5.3.5.2.2 Multicarrier BTS . 63 5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 65 5.3.5.3.1 Test case . 65 5.3.5.3.2 Test Environment . 66 5.3.6 Intermodulation attenuation . 66 5.3.6.1 Test case . 66 5.3.6.2 Test Environment . 68 5.3.7 Intra Base Station System intermodulation attenuation . 68 5.3.7.1 Test case . 68 5.3.7.2 Test Environment . 69 5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 69 5.3.8.1 Test case . 69 5.3.8.2 Test Environment . 71 5.3.9 Static reference sensitivity level . 71 5.3.9.1 Test case . 71 5.3.9.2 Test Environment . 73 5.3.10 Multipath Reference Sensitivity Level . 73 5.3.10.1 Test case . 73 5.3.10.2 Test Environment . 78 5.3.11 Reference Interference Level . 78 5.3.11.1 Test case . 78 5.3.11.2 Test Environment . 85 5.3.12 Blocking Characteristics . 85 5.3.12.1 Test case . 86 5.3.12.2 Test Environment . 89 5.3.13 Intermodulation characteristics . 89 5.3.13.1 Test case . 89 5.3.13.2 Test Environment . 91 5.3.14 AM suppression . 91 5.3.14.1 Test case . 91 5.3.14.2 Test Environment . 92 5.3.15 Spurious emissions from the receiver antenna connector . 92 5.3.15.1 Test case . 93 5.3.15.2 Test Environment . 93 5.3.16 Radiated spurious emissions . 93 5.3.16.1 Test case . 94 5.3.16.2 Test Environment . 95 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 96 Annex B (normative): General test conditions and declarations . 98 B.1 Declaration by manufacturer . 98 B.1.1 Output power and determination of power class . 98 B.1.2 Specified frequency range . 98 B.1.3 Frequency hopping . 99 B.1.4 RF power control .
...
Draft ETSI EN 301 502 V9.1.1 (2010-03)
Harmonized European Standard (Telecommunications series)
Global System for Mobile communications (GSM);
Harmonized EN for Base Station Equipment covering
the essential requirements of article 3.2 of
the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 502 V9.1.1 (2010-03)
Reference
REN/MSG-00005
Keywords
GSM
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 502 V9.1.1 (2010-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions and abbreviations . 10
3.1 Definitions . 10
3.2 Abbreviations . 12
4 Technical requirements specifications . 12
4.1 Environmental profile . 12
4.2 Conformance requirements . 13
4.2.1 Modulation accuracy. 13
4.2.1.1 Definition . 13
4.2.1.2 Limit . 13
4.2.1.3 Conformance . 14
4.2.2 Mean transmitted RF carrier power . 14
4.2.2.1 Definition . 14
4.2.2.2 Limit . 15
4.2.2.3 Conformance . 15
4.2.3 Transmitted RF carrier power versus time . 15
4.2.3.1 Definition . 15
4.2.3.2 Limit . 16
4.2.3.3 Conformance . 18
4.2.4 Adjacent channel power . 18
4.2.4.1 Spectrum due to modulation and wideband noise . 19
4.2.4.1.1 Definition. 19
4.2.4.1.2 Limit . 19
4.2.4.1.3 Conformance . 21
4.2.4.2 Switching transients spectrum . 21
4.2.4.2.1 Definition. 21
4.2.4.2.2 Limit . 21
4.2.4.2.3 Conformance . 21
4.2.5 Spurious emissions from the transmitter antenna connector . 21
4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 21
4.2.5.1.1 Definition. 21
4.2.5.1.2 Limit . 21
4.2.5.1.3 Conformance . 22
4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 22
4.2.5.2.1 Definition. 22
4.2.5.2.2 Limit . 22
4.2.5.2.3 Conformance . 23
4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 23
4.2.5.3.1 Definition. 23
4.2.5.3.2 Limit . 23
4.2.5.3.3 Conformance . 23
4.2.6 Intermodulation attenuation . 23
4.2.6.1 Definition . 23
4.2.6.2 Limit . 23
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 502 V9.1.1 (2010-03)
4.2.6.2.1 For all BTSs except multicarrier BTS . 23
4.2.6.2.2 For multicarrier BTS . 24
4.2.6.3 Conformance . 24
4.2.7 Intra Base Station System intermodulation attenuation . 24
4.2.7.1 Definition . 24
4.2.7.2 Limit . 24
4.2.7.2.1 For all BTSs except multicarrier BTS . 24
4.2.7.2.2 For multicarrier BTS . 24
4.2.7.3 Conformance . 24
4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 25
4.2.8.1 Definition . 25
4.2.8.2 Limit . 25
4.2.9 Static Reference Sensitivity Level . 26
4.2.9.1 Definition . 26
4.2.9.2 Limit . 26
4.2.9.3 Conformance . 29
4.2.10 Multipath Reference Sensitivity Level . 29
4.2.10.1 Definition . 29
4.2.10.2 Limit . 29
4.2.10.3 Conformance . 36
4.2.11 Reference Interference Level . 36
4.2.11.1 Definition . 36
4.2.11.2 Limit . 37
4.2.11.3 Conformance . 50
4.2.12 Blocking Characteristics . 50
4.2.12.1 Definition . 50
4.2.12.2 Limit . 50
4.2.12.2.1 Blocking . 50
4.2.12.2.2 Spurious response . 51
4.2.12.3 Conformance . 51
4.2.13 Intermodulation characteristics . 51
4.2.13.1 Definition . 51
4.2.13.2 Limit . 51
4.2.13.3 Conformance . 51
4.2.14 AM suppression . 51
4.2.14.1 Definition . 51
4.2.14.2 Limit . 52
4.2.14.3 Conformance . 52
4.2.15 Spurious emissions from the receiver antenna connector . 52
4.2.15.1 Definition . 52
4.2.15.2 Limit . 52
4.2.15.3 Conformance . 52
4.2.16 Radiated spurious emissions . 53
4.2.16.1 Definition . 53
4.2.16.2 Limit . 53
4.2.16.3 Conformance . 53
5 Testing for compliance with technical requirements . 53
5.1 Environmental conditions for testing . 53
5.2 Interpretation of the measurement results . 53
5.3 Essential radio test suites . 55
5.3.1 Modulation accuracy. 55
5.3.1.1 Test case . 55
5.3.1.2 Test Environment . 56
5.3.2 Mean transmitted RF carrier power . 56
5.3.2.1 Test case . 56
5.3.2.2 Test Environment . 57
5.3.3 Transmitted RF carrier power versus time . 57
5.3.2.1 Test case . 57
5.3.2.2 Test Environment . 58
5.3.4 Adjacent channel power . 58
5.3.4.1 Spectrum due to modulation and wideband noise . 58
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 502 V9.1.1 (2010-03)
5.3.4.1.1 Test case . 58
5.3.4.1.2 Test Environment . 59
5.3.4.2 Switching transients spectrum . 59
5.3.4.2.1 Test case . 59
5.3.4.2.2 Test Environment . 60
5.3.5 Spurious emissions from the transmitter antenna connector . 61
5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 61
5.3.5.1.1 Test case . 61
5.3.5.1.2 Test Environment . 61
5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 61
5.3.5.2.1 All base stations except multicarrier BTS . 61
5.3.5.2.2 Multicarrier BTS . 63
5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 64
5.3.5.3.1 Test case . 64
5.3.5.3.2 Test Environment . 65
5.3.6 Intermodulation attenuation . 65
5.3.6.1 Test case . 65
5.3.6.2 Test Environment . 66
5.3.7 Intra Base Station System intermodulation attenuation . 67
5.3.7.1 Test case . 67
5.3.7.2 Test Environment . 68
5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 68
5.3.8.1 Test case . 68
5.3.8.2 Test Environment . 69
5.3.9 Static Reference Sensitivity Level . 69
5.3.9.1 Test case . 69
5.3.9.2 Test Environment . 71
5.3.10 Multipath Reference Sensitivity Level . 72
5.3.10.1 Test case . 72
5.3.10.2 Test Environment . 76
5.3.11 Reference Interference Level . 76
5.3.11.1 Test case . 76
5.3.11.2 Test Environment . 83
5.3.12 Blocking Characteristics . 83
5.3.12.1 Test case . 83
5.3.12.2 Test Environment . 87
5.3.13 Intermodulation characteristics . 87
5.3.13.1 Test case . 87
5.3.13.2 Test Environment . 88
5.3.14 AM suppression . 88
5.3.14.1 Test case . 88
5.3.14.2 Test Environment . 89
5.3.15 Spurious emissions from the receiver antenna connector . 89
5.3.15.1 Test case . 89
5.3.15.2 Test Environment . 90
5.3.16 Radiated spurious emissions . 90
5.3.16.1 Test case . 90
5.3.16.2 Test Environment . 91
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 92
Annex B (normative): General test conditions and declarations . 95
B.1 Declaration by manufacturer . 95
B.1.1 Output power and determination of power class . 95
B.1.2 Specified frequency range . 95
B.1.3 Frequency hopping . 96
B.1.4 RF power control . 96
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 502 V9.1.1 (2010-03)
B.1.5 Downlink discontinuous transmi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.