ETSI EN 301 614-2 V1.1.2 (1999-02)
Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2: Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)
Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2: Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)
DEN/DECT-040104-2
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Digitalno omrežje z integriranimi storitvami (ISDN) - Vzajemno delovanje DECT/ISDN v obliki posredovalnega sistema - 2. del: Preskuševalna specifikacija, odvisna od profila (PSTS), za prenosno radijsko zaključitev (PT)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.REOLNLDigital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2: Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 301 614-2 V.1.23SIST EN 301 614-2:en01-QRYHPEHr-3SIST EN 301 614-2:SLOVENSKI
STANDARD
EN 301 614-2 V1.1.2 (1999-02)European Standard (Telecommunications series)Digital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN);DECT/ISDN interworking forintermediate system configuration;Part 2: Profile Specific Test Specification (PSTS) forPortable radio Termination (PT)SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)2ReferenceDEN/DECT-040104-2 (ey0i0idc.PDF)KeywordsDECT, ICS, ISDN, profileETSIPostal addressF-06921 Sophia Antipolis Cedex - FRANCEOffice address650 Route des Lucioles - Sophia AntipolisValbonne - FRANCETel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/88Internetsecretariat@etsi.frIndividual copies of this ETSI deliverablecan be downloaded fromhttp://www.etsi.orgIf you find errors in the present document, send yourcomment to: editor@etsi.frCopyright NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1999.All rights reserved.SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)3ContentsIntellectual Property Rights.7Foreword.71Scope.82Normative references.83Definitions and abbreviations.113.1Definitions.113.2Abbreviations.114DECT NWK layer protocol.124.1Additional Test Purposes (TPs).124.1.1Additional TPs for IIP CC specific behaviours.134.1.1.1Test group PT/CC/BV/IS.134.1.1.2Test group PT/CC/BI/IS.134.1.1.3Test group PT/CC/BO/IS.144.1.1.4Test group PT/CC/TI/IS.144.1.2Additional TPs for IIP LCE specific behaviours.144.1.2.1Test group PT/LC/BV/IS.144.2Abstract Test Method (ATM).144.3Relevant test cases.144.4Additional test cases.164.5Modified test cases.165DECT Data Link Control layer (DLC) layer protocol.175.1Additional TPs.175.1.1Additional TPs for C-plane class B procedures.195.1.1.1Test group CA.195.1.1.2Test group BV.215.1.1.3Test group BI.225.1.1.4Test group BO.235.1.2Additional TPs for U-plane LU7 procedures.245.1.2.1Test group BV.245.1.3Additional TPs for U-plane LU8 procedures.245.1.3.1Test group BV.245.2ATM.255.3Relevant test cases.255.4Additional test cases.255.4.1Additional test cases for C-plane class B.255.4.2Additional test cases for U-plane LU7.255.4.3Additional test cases for U-plane LU8.255.5Modified test cases.256DECT MAC layer protocol.266.1Additional TPs.266.1.1Additional TPs for advanced symmetric connections.276.1.2Additional TPs for C-plane switching procedures.276.1.2.1Dynamic switching CF to CS: DIFS initiated.276.1.2.2Dynamic switching CS to CF: DIPS initiated.286.1.2.3Dynamic switching CS to CF: DIFS initiated.286.1.2.4Dynamic switching CSx to CSy: DIFS initiated.296.1.3Additional TPs for U-plane switching procedures.296.1.3.1Connection handover procedure.296.1.3.2Release of part of double slot procedure.306.2ATM.306.3Relevant test cases.306.4Additional test cases.31SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)46.4.1Additional test cases for advanced symmetric connections.316.4.2Additional test cases for C-plane switching procedures.316.4.3Additional test cases for U-plane switching procedures.316.5Modified test cases.327DECT PHL protocol.327.1Additional TPs.327.2ATM.327.3Relevant test cases.327.4Additional test cases.327.5Modified test cases.328ISDN basic access protocols.338.1Applicability of ATS.338.2Additional TPs.338.3ATM.338.4Relevant test cases.339DECT/ISDN IIP profile.349.1Profile TSS.349.1.1Test groups.349.1.1.1Functional modules.349.1.1.2Main test groups.349.1.1.2.1Capability (CA) tests.349.1.1.2.2BV tests.359.1.1.2.3BO tests.359.1.1.2.4BI tests.359.2Profile TPs.359.2.1TP definition conventions.359.2.2TP naming conventions.369.2.3Sources of TP definitions.369.2.4TPs for IWU Link Association Entity.379.2.5TPs for IWU missing resource management.379.2.6TPs for IWU Call Control specific procedures.389.3Profile ATM.389.4Profile untestable TPs.399.5Profile ATS conventions.409.5.1Declarations part naming conventions.409.5.1.1Type and structured type definitions.409.5.1.2Operations definitions.409.5.1.3Parameter declarations.409.5.1.4Selection expression definitions.409.5.1.5Constant declarations.409.5.1.6Test suite variable declarations.419.5.1.7Test case variable declarations.419.5.1.8PCO declarations.419.5.1.9Timer declarations.419.5.1.10ASP type definitions.419.5.1.11PDU type definitions.429.5.1.12Alias definitions.429.5.2Constraints part naming conventions.429.5.3Dynamic part naming conventions.429.5.3.1Test Case identifier.439.5.3.2Test Step identifier.439.5.3.3Default identifier.439.5.3.4General aspects.439.5.3.5ATS abbreviations.449.5.4Declaration part implementation conventions.449.5.5Constraint part implementation conventions.449.5.6Dynamic part implementation conventions.459.5.7Documentation implementation conventions.45SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)59.6Test case and TP mapping.46Annex A (normative):Profile IXIT proforma.47A.1Identification summary.47A.2ATS summary.47A.3Test laboratory.47A.4Client identification.48A.5System Under Test (SUT).48A.6Profile information.49A.6.1NWK layer.49A.6.2DLC layer.51A.6.3MAC layer.53Annex B (normative):Profile Conformance Test Report (Profile CTR) proforma.55B.1Identification summary.55B.1.1Protocol conformance test report.55B.1.2IUT identification.55B.1.3Testing environment.56B.1.4Limits and reservation.56B.1.5Comments.56B.2IUT conformance status.56B.3Static conformance summary.57B.4Dynamic conformance summary.57B.5Static conformance review report.57B.6Test campaign report.58B.7Observations.58Annex C (normative):System Conformance Test Report (SCTR) proforma.59C.1Identification summary.59C.1.1System conformance test report.59C.1.2Test laboratory.59C.1.3Client identification.60C.1.4SUT.60C.1.5Profile identification.60C.1.6Nature of conformance testing.61C.1.7Limits and reservations.61C.1.8Record of agreement.61C.1.9Comments.62C.2System report summary for DECT/ISDN IIP PT.62C.2.1Profile testing summary for DECT NWK layer protocol.62C.2.2Profile testing summary for DECT DLC layer protocol.63C.2.3Profile testing summary for DECT MAC layer protocol.64C.2.4Profile testing summary for DECT PHL protocol.65C.2.5Profile testing summary for ISDN L2, L1 basic access protocol.66C.2.6Profile testing summary for DECT/ISDN IIP Profile.67Annex D (normative):Profile IXIT Requirements List (XRL) proforma.68D.1Profile eXtra Requirement List for IIP - PT part.68D.1.1Parameters for IWU layer.68D.1.2Specific parameters for NWK layer.68D.1.3Specific parameters for DLC layer.69SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)6D.1.4Specific parameters for MAC layer.69Annex E (normative):Modifications of DECT Common Interface (CI) PCTR proforma.70E.1Modifications of DECT NWK layer PCTR proforma.70E.2Modifications of DECT DLC layer PCTR proforma.73E.3Modifications of DECT MAC layer PCTR proforma.76E.4Observations.77Annex F (normative):Abstract Test Suite (ATS) - NWK layer.78F.1The TTCN Graphical form (TTCN.GR).78F.2The TTCN Machine Processable form (TTCN.MP).78Annex G (normative):Abstract Test Suite (ATS) - DLC layer.79G.1The TTCN Graphical form (TTCN.GR).79G.2The TTCN Machine Processable form (TTCN.MP).79Annex H (normative):Abstract Test Suite (ATS) - MAC layer.80H.1The TTCN Graphical form (TTCN.GR).80H.2The TTCN Machine Processable form (TTCN.MP).80Annex J (normative):Abstract Test Suite (ATS) - Interworking Unit (IWU).81J.1The TTCN Graphical form (TTCN.GR).81J.2The TTCN Machine Processable form (TTCN.MP).81History.82SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)7Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respectof ETSI standards", which is available free of charge from the ETSI Secretariat. Latest updates are available on theETSI Web server (http://www.etsi.org/ipr).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)which are, or may be, or may become, essential to the present document.ForewordThis European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced CordlessTelecommunications (DECT).The present document is part 2 of a multi-part EN covering the DECT/ISDN interworking for intermediate systemconfiguration, as identified below:Part 1:"Profile Test Specification (PTS) summary";Part 2:"Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)".National transposition datesDate of adoption of this EN:25 December 1998Date of latest announcement of this EN (doa):31 March 1999Date of latest publication of new National Standardor endorsement of this EN (dop/e):30 September 1999Date of withdrawal of any conflicting National Standard (dow):30 September 1999SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)81ScopeThe present document contains the test specification for Digital Enhanced Cordless Telecommunications/IntegratedServices Digital Network (DECT/ISDN) Interworking for Intermediate system Profile (IIP) Portable Part (PP)applications as specified in ETS 300 822 [22].This test specification provides conformance tests for DECT/ISDN terminal equipment conforming toETS 300 822 [22]. The main objective is to perform a high probability of inter-operability between the DECT/ISDNterminal equipment and an ISDN network. The DECT/ISDN terminal equipment contains Fixed Parts (FPs) and PPs thatmay be supplied by different manufacturers.The International Organization for Standardization (ISO) standard for the methodology of conformance testingISO/IEC 9646 [23] to [29] is used as the basis for the test methodology, and as the basis for test case specification.The test cases if listed in the present document have been derived from the corresponding ATS. Additional DECT/ISDNIIP specific test cases are included where required.Annex A provides Profile Implementation eXtra Information for Testing (IXIT) proforma part of this specification.Annex B provides Profile Conformance Test Report (Profile CTR) proforma part of this specification.Annex C provides System Conformance Test Report proforma (SCTR) part of this specification.Annex D provides the Profile IXIT Requirements List (XRL) proforma part of this specification.Annex E provides modifications of DECT layer PCTR proforma of this specification.Annex F provides the Tree and Tabular Combined Notation (TTCN) part for DECT Network (NWK) layer conformingto the requirements of this specification.Annex G provides the Tree and Tabular Combined Notation (TTCN) part for DECT DLC layer conforming to therequirements of this specification.Annex H provides the Tree and Tabular Combined Notation (TTCN) part for DECT Medium Access Control (MAC)layer conforming to the requirements of this specification.Annex J provides the Tree and Tabular Combined Notation (TTCN) part for DECT/ISDN IWU - IIP profile.2Normative referencesReferences may be made to:a)specific versions of publications (identified by date of publication, edition number, version number, etc.), inwhich case, subsequent revisions to the referenced document do not apply; orb)all versions up to and including the identified version (identified by "up to and including" before the versionidentity); orc)all versions subsequent to and including the identified version (identified by "onwards" following the versionidentity); ord)publications without mention of a specific version, in which case the latest version applies.A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the samenumber.[1]EN 301 241-1: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; ProfileImplementation Conformance Statement (ICS); Part 1: Portable radio Termination (PT)".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)9[2]EN 301 614-2: " Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2:Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)".[3]ETS 300 012 (1992) including Amendment 2 (1996): "Integrated Services Digital Network(ISDN); Basic user-network interface; Layer 1 specification and test principles".[4]Void.[5]EN 300 175-2: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 2: Physical Layer (PHL)".[6]EN 300 175-3: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 3: Medium Access Control (MAC) layer".[7]EN 300 175-4: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 4: Data Link Control (DLC) layer".[8]EN 300 175-5: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 5: Network (NWK) layer".[9]EN 300 176-1: "Digital Enhanced Cordless Telecommunications (DECT); Approval testspecification (ATS); Part 1: Radio".[10]ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 2: General protocol specification[ITU-T Recommendation Q.921 (1993), modified]".[11]ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 4: Protocol Implementation ConformanceStatement (PICS) proforma specification for the general protocol".[12]ETS 300 476-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 1: Network (NWK)layer - Portable radio Termination (PT)".[13]ETS 300 476-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 2: Data LinkControl (DLC) layer - Portable radio Termination (PT)".[14]ETS 300 476-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 3: Medium AccessControl (MAC) layer - Portable radio Termination (PT)".[15]ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer".[16]EN 300 497-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for MediumAccess Control (MAC) layer".[17]EN 300 497-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Portable radio Termination (PT)".[18]ETS 300 497-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - DataLink Control (DLC) layer".[19]ETS 300 497-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC) layer".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)10[20]ETS 300 497-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) -Network (NWK) layer - Portable radio Termination (PT)".[21]ETS 300 497-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 7: Abstract Test Suite (ATS) for Network (NWK) layer -Portable radio Termination (PT)".[22]ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration;Interworking and profile specification".[23]ISO/IEC 9646-1 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 1: General concepts". (See alsoCCITT Recommendation X.290 (1991)).[24]ISO/IEC 9646-2 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 2: Abstract test suite specification". (See alsoCCITT Recommendation X.291 (1991)).[25]ISO/IEC 9646-3 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 3: The Tree and Tabular Combined Notation TTCN)".(See also CCITT Recommendation X.292 (1992)).[26]ISO/IEC 9646-4 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 4: Test realization". (See alsoCCITT Recommendation X.292 (1992)).[27]ISO/IEC 9646-5 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 5: Requirements on test laboratories and clients for theconformance assessment process". (See also CCITT Recommendation X.292 (1992)).[28]ISO/IEC 9646-6 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 6: Protocol profile test specification".[29]ISO/IEC 9646-7 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 7: Implementation Conformance Statement".[30]TBR 3: "Integrated Services Digital Network (ISDN); Attachment requirements for terminalequipment to connect to an ISDN using ISDN basic access".[31]TBR 22: "Radio Equipment and Systems (RES); Attachment requirements for terminal equipmentfor Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP)applications".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)113Definitions and abbreviations3.1DefinitionsFor the purposes of the present document, the following terms and definitions apply:a)the terms defined in ISO/IEC 9646-7 [29]; andb)the definitions in ETS 300 822 [22].3.2AbbreviationsFor the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 [23], ISO/IEC 9646-6 [28],ISO/IEC 9646-7 [29], ETS 300 822 [22] apply. In particular, the following abbreviations apply:ASPAbstract Service PrimitiveATMAbstract Test MethodATSAbstract Test SuiteBIInvalid BehaviourBOInopportune BehaviourBVValid BehaviourCACApability testsCCCall Control entityCICommon InterfaceDECTDigital Enhanced Cordless TelecommunicationsDLCData Link Control layerFPFixed PartFTFixed radio TerminationICSImplementation Conformance StatementISDNIntegrated Services Digital NetworkISOInternational Organization for StandardizationIUTImplementation Under TestIXITImplementation Extra Information for TestingLCELink Control EntityMACMedium Access Control layerMMMobility Management entityMTCMain Text ComponentNWKNetWorKPDUProtocol Data UnitPHLPhysical LayerPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPPPortable PartPSTSProfile Specific Test SpecificationPTPortable radio TerminationPTSProfile Test SpecificationSAPService Access PointSCSSystem Conformance StatementSUTSystem Under TestTPTest PurposeTSSTest Suite StructureXRLIXIT Requirements listSIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)124DECT NWK layer protocol4.1Additional Test Purposes (TPs)Figure 1 shows the Network (NWK) Test Suite Structure (TSS) defined in ETS 300 497-6 [20] for the conformancetesting.CCLCICCICRSCBVBIITBVBITIBVBVTIISMLLRLSRSBOTIBIBVMOBVLLLEAUPRKACACABOMMLOPMNWKMEBOOCITIDARCHFigure 1: NWK TSSSIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)13No TP for Call Control entity (CC) entity of the NWK layer as specified in ETS 300 497-6 [20] applies withoutmodification. The test groups "Portable radio Termination (PT)/CC/Valid Behaviour (BV)/IS", "PT/CC/InopportuneBehaviour (BO)/IS", "PT/CC/Invalid Behaviour (BI)/IS" and "PT/CC/TI/IS" have been added to test the intermediatesystem profile specific behaviours.All TPs for Link Control Entity (LCE) entity of the NWK layer as specified in ETS 300 497-6 [20] apply. The testgroups "PT/LC/BV/IS", has been added to test the intermediate system profile specific behaviours.No TP for CISS entity of the NWK layer is relevant.4.1.1Additional TPs for IIP CC specific behaviours4.1.1.1Test group PT/CC/BV/ISTP-PT-CC-BV-IS-01ETS 300 822 [22], subclause 10.1.3 and annex CInitial condition: The signalling link is established, the CC state is t10.Check that the Implementation Under Test (IUT) supports segmentation of longISDN messages into two <> with a <>sent in five or more consecutive messagesTP-PT-CC-BV-IS-02ETS 300 822 [22], subclause 10.1.3 and annex CInitial condition: The signalling link is established, the CC state is t10.Check that the IUT supports segmentation of medium sized ISDN messagesinto one <> in two consecutive messagesTP-PT-CC-BV-IS-03ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch the ISDN channel B1 separately.TP-PT-CC-BV-IS-04ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch the ISDN channel B2 separately.TP-PT-CC-BV-IS-05ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch both the ISDN channels B1 and B2.TP-PT-CC-BV-IS-06ETS 300 822 [22], subclause 10.2.2Initial condition: a first link supports the U-plane for B1 channel and Cssignalling data, the second one supports only the U-plane for B2 and is in statet10Check that the U-plane for B2 when no longer needed, the IUT supports itsrelease using the normal release procedure.TP-PT-CC-BV-IS-07ETS 300 822 [22], subclause 10.2.2Initial condition: a first link supports the U-plane for B1 channel and Cssignalling data, the second one supports only the U-plane for B2 and is in statet08.Check that the U-plane for B2 when no longer needed, the IUT supports itsrelease using the normal release procedure.TP-PT-CC-BV-IS-08ETS 300 822 [22], subclause 10.2.3Initial condition: The U-plane is connected, the CC is in state t10.Check that the IUT supports disconnection/connection of the U-plane link bymeans of {IWU-INFO} messages4.1.1.2Test group PT/CC/BI/ISTP-PT-CC-BI-IS-01EN 300 175-5 [8], subclause 17.6.1Initial condition: The link is not established, the CC is in state t00Verify that the IUT sends a {CC_RELEASE_COM} on receipt of a {CC_SETUP}message with a mandatory information element missing.TP-PT-CC-BI-IS-02EN 300 175-5 [8], subclause 17.6.2Initial condition: The link is not established, the CC is in state t00Verify that the IUT sends a {CC_RELEASE_COM} on receipt of a {CC_SETUP}message containing a mandatory information element with wrong content.TP-PT-CC-BI-IS-03EN 300 175-5 [8], subclause 17.4.1Initial condition: The link is not established, the CC is in state t00Verify that the IUT ignores an unrecognized message, when it is constructed asa {CC_SETUP} with one bit wrong in the <>SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)144.1.1.3Test group PT/CC/BO/ISTP-PT-CC-B0-IS-01EN 300 175-5 [8], subclause 9.3.2.8Initial condition: The link is established, the CC is in state t08Verify that the IUT ignores an unexpected message {CC_CALL_PROC} in statet08.4.1.1.4Test group PT/CC/TI/ISTP-PT-CC-TI-IS-01EN 300 175-5 [8], subclause 9.3.2.8Initial condition: The link is established, the CC is in state t08Verify that the IUT, after having started timer P-, releases the callusing the normal procedure when the timer expires after the defined time. The{CC_R
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.REOLNLDigital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2: Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 301 614-2 Version 1.1.2SIST EN 301 614-2:2000en01-januar-2000SIST EN 301 614-2:2000SLOVENSKI
STANDARD
EN 301 614-2 V1.1.2 (1999-02)European Standard (Telecommunications series)Digital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN);DECT/ISDN interworking forintermediate system configuration;Part 2: Profile Specific Test Specification (PSTS) forPortable radio Termination (PT)SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)2ReferenceDEN/DECT-040104-2 (ey0i0idc.PDF)KeywordsDECT, ICS, ISDN, profileETSIPostal addressF-06921 Sophia Antipolis Cedex - FRANCEOffice address650 Route des Lucioles - Sophia AntipolisValbonne - FRANCETel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/88Internetsecretariat@etsi.frIndividual copies of this ETSI deliverablecan be downloaded fromhttp://www.etsi.orgIf you find errors in the present document, send yourcomment to: editor@etsi.frCopyright NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1999.All rights reserved.SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)3ContentsIntellectual Property Rights.7Foreword.71Scope.82Normative references.83Definitions and abbreviations.113.1Definitions.113.2Abbreviations.114DECT NWK layer protocol.124.1Additional Test Purposes (TPs).124.1.1Additional TPs for IIP CC specific behaviours.134.1.1.1Test group PT/CC/BV/IS.134.1.1.2Test group PT/CC/BI/IS.134.1.1.3Test group PT/CC/BO/IS.144.1.1.4Test group PT/CC/TI/IS.144.1.2Additional TPs for IIP LCE specific behaviours.144.1.2.1Test group PT/LC/BV/IS.144.2Abstract Test Method (ATM).144.3Relevant test cases.144.4Additional test cases.164.5Modified test cases.165DECT Data Link Control layer (DLC) layer protocol.175.1Additional TPs.175.1.1Additional TPs for C-plane class B procedures.195.1.1.1Test group CA.195.1.1.2Test group BV.215.1.1.3Test group BI.225.1.1.4Test group BO.235.1.2Additional TPs for U-plane LU7 procedures.245.1.2.1Test group BV.245.1.3Additional TPs for U-plane LU8 procedures.245.1.3.1Test group BV.245.2ATM.255.3Relevant test cases.255.4Additional test cases.255.4.1Additional test cases for C-plane class B.255.4.2Additional test cases for U-plane LU7.255.4.3Additional test cases for U-plane LU8.255.5Modified test cases.256DECT MAC layer protocol.266.1Additional TPs.266.1.1Additional TPs for advanced symmetric connections.276.1.2Additional TPs for C-plane switching procedures.276.1.2.1Dynamic switching CF to CS: DIFS initiated.276.1.2.2Dynamic switching CS to CF: DIPS initiated.286.1.2.3Dynamic switching CS to CF: DIFS initiated.286.1.2.4Dynamic switching CSx to CSy: DIFS initiated.296.1.3Additional TPs for U-plane switching procedures.296.1.3.1Connection handover procedure.296.1.3.2Release of part of double slot procedure.306.2ATM.306.3Relevant test cases.306.4Additional test cases.31SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)46.4.1Additional test cases for advanced symmetric connections.316.4.2Additional test cases for C-plane switching procedures.316.4.3Additional test cases for U-plane switching procedures.316.5Modified test cases.327DECT PHL protocol.327.1Additional TPs.327.2ATM.327.3Relevant test cases.327.4Additional test cases.327.5Modified test cases.328ISDN basic access protocols.338.1Applicability of ATS.338.2Additional TPs.338.3ATM.338.4Relevant test cases.339DECT/ISDN IIP profile.349.1Profile TSS.349.1.1Test groups.349.1.1.1Functional modules.349.1.1.2Main test groups.349.1.1.2.1Capability (CA) tests.349.1.1.2.2BV tests.359.1.1.2.3BO tests.359.1.1.2.4BI tests.359.2Profile TPs.359.2.1TP definition conventions.359.2.2TP naming conventions.369.2.3Sources of TP definitions.369.2.4TPs for IWU Link Association Entity.379.2.5TPs for IWU missing resource management.379.2.6TPs for IWU Call Control specific procedures.389.3Profile ATM.389.4Profile untestable TPs.399.5Profile ATS conventions.409.5.1Declarations part naming conventions.409.5.1.1Type and structured type definitions.409.5.1.2Operations definitions.409.5.1.3Parameter declarations.409.5.1.4Selection expression definitions.409.5.1.5Constant declarations.409.5.1.6Test suite variable declarations.419.5.1.7Test case variable declarations.419.5.1.8PCO declarations.419.5.1.9Timer declarations.419.5.1.10ASP type definitions.419.5.1.11PDU type definitions.429.5.1.12Alias definitions.429.5.2Constraints part naming conventions.429.5.3Dynamic part naming conventions.429.5.3.1Test Case identifier.439.5.3.2Test Step identifier.439.5.3.3Default identifier.439.5.3.4General aspects.439.5.3.5ATS abbreviations.449.5.4Declaration part implementation conventions.449.5.5Constraint part implementation conventions.449.5.6Dynamic part implementation conventions.459.5.7Documentation implementation conventions.45SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)59.6Test case and TP mapping.46Annex A (normative):Profile IXIT proforma.47A.1Identification summary.47A.2ATS summary.47A.3Test laboratory.47A.4Client identification.48A.5System Under Test (SUT).48A.6Profile information.49A.6.1NWK layer.49A.6.2DLC layer.51A.6.3MAC layer.53Annex B (normative):Profile Conformance Test Report (Profile CTR) proforma.55B.1Identification summary.55B.1.1Protocol conformance test report.55B.1.2IUT identification.55B.1.3Testing environment.56B.1.4Limits and reservation.56B.1.5Comments.56B.2IUT conformance status.56B.3Static conformance summary.57B.4Dynamic conformance summary.57B.5Static conformance review report.57B.6Test campaign report.58B.7Observations.58Annex C (normative):System Conformance Test Report (SCTR) proforma.59C.1Identification summary.59C.1.1System conformance test report.59C.1.2Test laboratory.59C.1.3Client identification.60C.1.4SUT.60C.1.5Profile identification.60C.1.6Nature of conformance testing.61C.1.7Limits and reservations.61C.1.8Record of agreement.61C.1.9Comments.62C.2System report summary for DECT/ISDN IIP PT.62C.2.1Profile testing summary for DECT NWK layer protocol.62C.2.2Profile testing summary for DECT DLC layer protocol.63C.2.3Profile testing summary for DECT MAC layer protocol.64C.2.4Profile testing summary for DECT PHL protocol.65C.2.5Profile testing summary for ISDN L2, L1 basic access protocol.66C.2.6Profile testing summary for DECT/ISDN IIP Profile.67Annex D (normative):Profile IXIT Requirements List (XRL) proforma.68D.1Profile eXtra Requirement List for IIP - PT part.68D.1.1Parameters for IWU layer.68D.1.2Specific parameters for NWK layer.68D.1.3Specific parameters for DLC layer.69SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)6D.1.4Specific parameters for MAC layer.69Annex E (normative):Modifications of DECT Common Interface (CI) PCTR proforma.70E.1Modifications of DECT NWK layer PCTR proforma.70E.2Modifications of DECT DLC layer PCTR proforma.73E.3Modifications of DECT MAC layer PCTR proforma.76E.4Observations.77Annex F (normative):Abstract Test Suite (ATS) - NWK layer.78F.1The TTCN Graphical form (TTCN.GR).78F.2The TTCN Machine Processable form (TTCN.MP).78Annex G (normative):Abstract Test Suite (ATS) - DLC layer.79G.1The TTCN Graphical form (TTCN.GR).79G.2The TTCN Machine Processable form (TTCN.MP).79Annex H (normative):Abstract Test Suite (ATS) - MAC layer.80H.1The TTCN Graphical form (TTCN.GR).80H.2The TTCN Machine Processable form (TTCN.MP).80Annex J (normative):Abstract Test Suite (ATS) - Interworking Unit (IWU).81J.1The TTCN Graphical form (TTCN.GR).81J.2The TTCN Machine Processable form (TTCN.MP).81History.82SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)7Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respectof ETSI standards", which is available free of charge from the ETSI Secretariat. Latest updates are available on theETSI Web server (http://www.etsi.org/ipr).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)which are, or may be, or may become, essential to the present document.ForewordThis European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced CordlessTelecommunications (DECT).The present document is part 2 of a multi-part EN covering the DECT/ISDN interworking for intermediate systemconfiguration, as identified below:Part 1:"Profile Test Specification (PTS) summary";Part 2:"Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)";Part 3:"Profile Specific Test Specification (PSTS) for Fixed radio Termination (FT)".National transposition datesDate of adoption of this EN:25 December 1998Date of latest announcement of this EN (doa):31 March 1999Date of latest publication of new National Standardor endorsement of this EN (dop/e):30 September 1999Date of withdrawal of any conflicting National Standard (dow):30 September 1999SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)81ScopeThe present document contains the test specification for Digital Enhanced Cordless Telecommunications/IntegratedServices Digital Network (DECT/ISDN) Interworking for Intermediate system Profile (IIP) Portable Part (PP)applications as specified in ETS 300 822 [22].This test specification provides conformance tests for DECT/ISDN terminal equipment conforming toETS 300 822 [22]. The main objective is to perform a high probability of inter-operability between the DECT/ISDNterminal equipment and an ISDN network. The DECT/ISDN terminal equipment contains Fixed Parts (FPs) and PPs thatmay be supplied by different manufacturers.The International Organization for Standardization (ISO) standard for the methodology of conformance testingISO/IEC 9646 [23] to [29] is used as the basis for the test methodology, and as the basis for test case specification.The test cases if listed in the present document have been derived from the corresponding ATS. Additional DECT/ISDNIIP specific test cases are included where required.Annex A provides Profile Implementation eXtra Information for Testing (IXIT) proforma part of this specification.Annex B provides Profile Conformance Test Report (Profile CTR) proforma part of this specification.Annex C provides System Conformance Test Report proforma (SCTR) part of this specification.Annex D provides the Profile IXIT Requirements List (XRL) proforma part of this specification.Annex E provides modifications of DECT layer PCTR proforma of this specification.Annex F provides the Tree and Tabular Combined Notation (TTCN) part for DECT Network (NWK) layer conformingto the requirements of this specification.Annex G provides the Tree and Tabular Combined Notation (TTCN) part for DECT DLC layer conforming to therequirements of this specification.Annex H provides the Tree and Tabular Combined Notation (TTCN) part for DECT Medium Access Control (MAC)layer conforming to the requirements of this specification.Annex J provides the Tree and Tabular Combined Notation (TTCN) part for DECT/ISDN IWU - IIP profile.2Normative referencesReferences may be made to:a)specific versions of publications (identified by date of publication, edition number, version number, etc.), inwhich case, subsequent revisions to the referenced document do not apply; orb)all versions up to and including the identified version (identified by "up to and including" before the versionidentity); orc)all versions subsequent to and including the identified version (identified by "onwards" following the versionidentity); ord)publications without mention of a specific version, in which case the latest version applies.A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the samenumber.[1]EN 301 241-1: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; ProfileImplementation Conformance Statement (ICS); Part 1: Portable radio Termination (PT)".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)9[2]EN 301 614-2: " Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration; Part 2:Profile Specific Test Specification (PSTS) for Portable radio Termination (PT)".[3]ETS 300 012 (1992) including Amendment 2 (1996): "Integrated Services Digital Network(ISDN); Basic user-network interface; Layer 1 specification and test principles".[4]Void.[5]EN 300 175-2: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 2: Physical Layer (PHL)".[6]EN 300 175-3: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 3: Medium Access Control (MAC) layer".[7]EN 300 175-4: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 4: Data Link Control (DLC) layer".[8]EN 300 175-5: "Digital European Cordless Telecommunications (DECT); Common Interface (CI);Part 5: Network (NWK) layer".[9]EN 300 176-1: "Digital Enhanced Cordless Telecommunications (DECT); Approval testspecification (ATS); Part 1: Radio".[10]ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 2: General protocol specification[ITU-T Recommendation Q.921 (1993), modified]".[11]ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Data link layer; Part 4: Protocol Implementation ConformanceStatement (PICS) proforma specification for the general protocol".[12]ETS 300 476-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 1: Network (NWK)layer - Portable radio Termination (PT)".[13]ETS 300 476-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 2: Data LinkControl (DLC) layer - Portable radio Termination (PT)".[14]ETS 300 476-3: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 3: Medium AccessControl (MAC) layer - Portable radio Termination (PT)".[15]ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer".[16]EN 300 497-1: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 1: Test Suite Structure (TSS) and Test Purposes (TP) for MediumAccess Control (MAC) layer".[17]EN 300 497-2: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI)Test Case Library (TCL); Part 2: Abstract Test Suite (ATS) for Medium Access Control (MAC)layer - Portable radio Termination (PT)".[18]ETS 300 497-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 4: Test Suite Structure (TSS) and Test Purposes (TP) - DataLink Control (DLC) layer".[19]ETS 300 497-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 5: Abstract Test Suite (ATS) - Data Link Control (DLC) layer".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)10[20]ETS 300 497-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) -Network (NWK) layer - Portable radio Termination (PT)".[21]ETS 300 497-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface(CI) Test Case Library (TCL); Part 7: Abstract Test Suite (ATS) for Network (NWK) layer -Portable radio Termination (PT)".[22]ETS 300 822: "Digital Enhanced Cordless Telecommunications (DECT); Integrated ServicesDigital Network (ISDN); DECT/ISDN interworking for intermediate system configuration;Interworking and profile specification".[23]ISO/IEC 9646-1 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 1: General concepts". (See alsoCCITT Recommendation X.290 (1991)).[24]ISO/IEC 9646-2 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 2: Abstract test suite specification". (See alsoCCITT Recommendation X.291 (1991)).[25]ISO/IEC 9646-3 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 3: The Tree and Tabular Combined Notation TTCN)".(See also CCITT Recommendation X.292 (1992)).[26]ISO/IEC 9646-4 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 4: Test realization". (See alsoCCITT Recommendation X.292 (1992)).[27]ISO/IEC 9646-5 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 5: Requirements on test laboratories and clients for theconformance assessment process". (See also CCITT Recommendation X.292 (1992)).[28]ISO/IEC 9646-6 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 6: Protocol profile test specification".[29]ISO/IEC 9646-7 (1991): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 7: Implementation Conformance Statement".[30]TBR 3: "Integrated Services Digital Network (ISDN); Attachment requirements for terminalequipment to connect to an ISDN using ISDN basic access".[31]TBR 22: "Radio Equipment and Systems (RES); Attachment requirements for terminal equipmentfor Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP)applications".SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)113Definitions and abbreviations3.1DefinitionsFor the purposes of the present document, the following terms and definitions apply:a)the terms defined in ISO/IEC 9646-7 [29]; andb)the definitions in ETS 300 822 [22].3.2AbbreviationsFor the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 [23], ISO/IEC 9646-6 [28],ISO/IEC 9646-7 [29], ETS 300 822 [22] apply. In particular, the following abbreviations apply:ASPAbstract Service PrimitiveATMAbstract Test MethodATSAbstract Test SuiteBIInvalid BehaviourBOInopportune BehaviourBVValid BehaviourCACApability testsCCCall Control entityCICommon InterfaceDECTDigital Enhanced Cordless TelecommunicationsDLCData Link Control layerFPFixed PartFTFixed radio TerminationICSImplementation Conformance StatementISDNIntegrated Services Digital NetworkISOInternational Organization for StandardizationIUTImplementation Under TestIXITImplementation Extra Information for TestingLCELink Control EntityMACMedium Access Control layerMMMobility Management entityMTCMain Text ComponentNWKNetWorKPDUProtocol Data UnitPHLPhysical LayerPICSProtocol Implementation Conformance StatementPIXITProtocol Implementation eXtra Information for TestingPPPortable PartPSTSProfile Specific Test SpecificationPTPortable radio TerminationPTSProfile Test SpecificationSAPService Access PointSCSSystem Conformance StatementSUTSystem Under TestTPTest PurposeTSSTest Suite StructureXRLIXIT Requirements listSIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)124DECT NWK layer protocol4.1Additional Test Purposes (TPs)Figure 1 shows the Network (NWK) Test Suite Structure (TSS) defined in ETS 300 497-6 [20] for the conformancetesting.CCLCICCICRSCBVBIITBVBITIBVBVTIISMLLRLSRSBOTIBIBVMOBVLLLEAUPRKACACABOMMLOPMNWKMEBOOCITIDARCHFigure 1: NWK TSSSIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)13No TP for Call Control entity (CC) entity of the NWK layer as specified in ETS 300 497-6 [20] applies withoutmodification. The test groups "Portable radio Termination (PT)/CC/Valid Behaviour (BV)/IS", "PT/CC/InopportuneBehaviour (BO)/IS", "PT/CC/Invalid Behaviour (BI)/IS" and "PT/CC/TI/IS" have been added to test the intermediatesystem profile specific behaviours.All TPs for Link Control Entity (LCE) entity of the NWK layer as specified in ETS 300 497-6 [20] apply. The testgroups "PT/LC/BV/IS", has been added to test the intermediate system profile specific behaviours.No TP for CISS entity of the NWK layer is relevant.4.1.1Additional TPs for IIP CC specific behaviours4.1.1.1Test group PT/CC/BV/ISTP-PT-CC-BV-IS-01ETS 300 822 [22], subclause 10.1.3 and annex CInitial condition: The signalling link is established, the CC state is t10.Check that the Implementation Under Test (IUT) supports segmentation of longISDN messages into two <> with a <>sent in five or more consecutive messagesTP-PT-CC-BV-IS-02ETS 300 822 [22], subclause 10.1.3 and annex CInitial condition: The signalling link is established, the CC state is t10.Check that the IUT supports segmentation of medium sized ISDN messagesinto one <> in two consecutive messagesTP-PT-CC-BV-IS-03ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch the ISDN channel B1 separately.TP-PT-CC-BV-IS-04ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch the ISDN channel B2 separately.TP-PT-CC-BV-IS-05ETS 300 822 [22], subclause 10.2.1 and 6.3.2Initial condition: The link is not established, the CC is idle.Check that the IUT can switch both the ISDN channels B1 and B2.TP-PT-CC-BV-IS-06ETS 300 822 [22], subclause 10.2.2Initial condition: a first link supports the U-plane for B1 channel and Cssignalling data, the second one supports only the U-plane for B2 and is in statet10Check that the U-plane for B2 when no longer needed, the IUT supports itsrelease using the normal release procedure.TP-PT-CC-BV-IS-07ETS 300 822 [22], subclause 10.2.2Initial condition: a first link supports the U-plane for B1 channel and Cssignalling data, the second one supports only the U-plane for B2 and is in statet08.Check that the U-plane for B2 when no longer needed, the IUT supports itsrelease using the normal release procedure.TP-PT-CC-BV-IS-08ETS 300 822 [22], subclause 10.2.3Initial condition: The U-plane is connected, the CC is in state t10.Check that the IUT supports disconnection/connection of the U-plane link bymeans of {IWU-INFO} messages4.1.1.2Test group PT/CC/BI/ISTP-PT-CC-BI-IS-01EN 300 175-5 [8], subclause 17.6.1Initial condition: The link is not established, the CC is in state t00Verify that the IUT sends a {CC_RELEASE_COM} on receipt of a {CC_SETUP}message with a mandatory information element missing.TP-PT-CC-BI-IS-02EN 300 175-5 [8], subclause 17.6.2Initial condition: The link is not established, the CC is in state t00Verify that the IUT sends a {CC_RELEASE_COM} on receipt of a {CC_SETUP}message containing a mandatory information element with wrong content.TP-PT-CC-BI-IS-03EN 300 175-5 [8], subclause 17.4.1Initial condition: The link is not established, the CC is in state t00Verify that the IUT ignores an unrecognized message, when it is constructed asa {CC_SETUP} with one bit wrong in the <>SIST EN 301 614-2:2000
ETSIEN 301 614-2 V1.1.2 (1999-02)144.1.1.3Test group PT/CC/BO/ISTP-PT-CC-B0-IS-01EN 300 175-5 [8], subclause 9.3.2.8Initial condition: The link is established, the CC is in state t08Verify that the IUT ignores an unexpected message {CC_CALL_PROC} in statet08.4.1.1.4Test group PT/CC/TI/ISTP-PT-CC-TI-IS-01EN 300 175-5 [8], subclause 9.3.2.8Initial condition: The link is established, the CC is in state t08Verify that the IUT, after having started timer P-, releases the callusing the normal procedure when the timer expires after the define
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...