IEC 61156-3:2008
(Main)Multicore and symmetrical pair/quad cables for digital communications - Part 3: Work area cable - Sectional specification
Multicore and symmetrical pair/quad cables for digital communications - Part 3: Work area cable - Sectional specification
IEC 61156-3:2008(E) defines individually screened, common overall core screen and unscreened pairs or quads in cables for work area wiring. These cables are suitable for the various communication systems for which the reference is given in the relevant detail specification. The cables covered by this sectional specification are intended to operate with voltages and currents normally adopted for communication systems. These cables should not be connected to low impedance sources, for example, the public mains electricity supply. The cables are specifically intended for work area wiring as defined in ISO/IEC 11801. This third edition cancels and replaces the second edition published in 2003. This edition constitutes a technical revision and includes the following significant technical changes with respect to the previous edition:
a) new requirements for new cables Cat3, and Cat5 applications;
b) a better numbering in order to take into account the generic specification.
General Information
Relations
Standards Content (Sample)
IEC 61156-3
Edition 3.0 2008-11
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –
Part 3: Work area cable – Sectional specification
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61156-3
Edition 3.0 2008-11
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –
Part 3: Work area cable – Sectional specification
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
N
ICS 33.120.20 ISBN 978-2-88910-420-8
– 2 – 61156-3 © IEC:2008(E)
CONTENTS
FOREWORD.4
1 General .6
1.1 Scope.6
1.2 Normative references .6
1.3 Installation considerations.6
2 Definitions, materials and cable construction.6
2.1 Definitions .6
2.2 Materials and cable construction.7
2.2.1 General remarks.7
2.2.2 Cable construction .7
2.2.3 Conductor.7
2.2.4 Insulation.7
2.2.5 Colour code of insulation.7
2.2.6 Cable element .7
2.2.7 Screening of the cable element .7
2.2.8 Cable make-up .8
2.2.9 Screening of the cable core.8
2.2.10 Sheath.8
2.2.11 Colour of sheath .8
2.2.12 Identification .8
2.2.13 Finished cable .8
3 Characteristics and requirements.8
3.1 General remarks.8
3.2 Electrical characteristics .9
3.2.1 Conductor resistance .9
3.2.2 Resistance unbalance.9
3.2.3 Dielectric strength.9
3.2.4 Insulation resistance .9
3.2.5 Mutual capacitance .9
3.2.6 Capacitance unbalance.9
3.2.7 Transfer impedance.9
3.3 Transmission characteristics.9
3.3.1 Velocity of propagation (phase velocity) .9
3.3.2 Attenuation .10
3.3.3 Unbalance attenuation .10
3.3.4 Near-end crosstalk (NEXT) .10
3.3.5 Characteristic impedance.11
3.3.6 Structural Return Loss (SRL) .11
3.4 Mechanical and dimensional characteristics and requirements .12
3.4.1 Dimensional requirements.12
3.4.2 Elongation at break of the conductors .12
3.4.3 Elongation at break of the insulation.12
3.4.4 Elongation at break of the sheath.12
3.4.5 Tensile strength of the sheath .12
3.4.6 Crush test of the cable.12
3.4.7 Impact test of the cable.12
3.4.8 Repeated bending of the cable.12
61156-3 © IEC:2008(E) – 3 –
3.4.9 Tensile performance of the cable .13
3.5 Environmental characteristics .13
3.5.1 Shrinkage of insulation.13
3.5.2 Wrapping test of insulation after thermal ageing .13
3.5.3 Bending test of insulation at low temperature .13
3.5.4 Elongation at break of the sheath after ageing.13
3.5.5 Tensile strength of the sheath after ageing.13
3.5.6 Sheath pressure test at high temperature.13
3.5.7 Cold bend test of the cable .13
3.5.8 Heat shock test.13
3.5.9 Flame propagation characteristics of a single cable.13
3.5.10 Flame propagation characteristics of bunched cables.13
3.5.11 Acid gas evolution.13
3.5.12 Smoke generation.14
3.5.13 Toxic gas emission .14
3.5.14 Combined flame and smoke test for cables in environmental air
handling space .14
4 Introduction to the blank detail specification .14
Table 1 – Constants .
Table 2 – NEXT, PSNEXT constants .11
Table 3 – Input impedance values .11
Table 4 – Function fitted impedance .11
Table 5 – Structural return loss (dB min) .12
– 4 – 61156-3 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES
FOR DIGITAL COMMUNICATIONS –
Part 3: Work area cable –
Sectional specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61156-6 has been prepared by subcommittee 46C: Wires and
symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors,
R.F. and microwave passive components and accessories.
This third edition cancels and replaces the second edition published in 2003. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) new requirements for new cables Cat3, and Cat5 applications;
b) a better numbering in order to take into account
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.