IEC TS 60034-32:2016

Rotating electrical machines - Part 32: Measurement of stator end-winding vibration at form-wound windings

IEC TS 60034-32:2016(E) is intended to provide consistent guidelines for measuring and reporting end-winding vibration behaviour during operation and at standstill. It
- defines terms for measuring, analysis and evaluation of stator end-winding vibration and related structural dynamics;
- gives guidelines for measuring dynamic / structural characteristics offline and stator end-winding vibrations online;
- describes instrumentation and installation practices for end-winding vibration measurement equipment;
- establishes general principles for documentation of test results;
- describes the theoretical background of stator end-winding vibrations. This part of IEC 60034 is applicable to three-phase synchronous generators and three-phase synchronous direct online (DOL) motors.

General Information

• Status: Published
• Publication Date: 14-Dec-2016
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 29.160.01 - Rotating machinery in general
• Technical Committee: TC 2 - Rotating machinery
• Drafting Committee: WG 32 - TC 2/WG 32
• Current Stage: PPUB - Publication issued
• Start Date: 28-Feb-2017
• Completion Date: 15-Dec-2016

Standards Content (Sample)

IEC TS 60034-32 ®
Edition 1.0 2016-12
TECHNICAL
SPECIFICATION
colour
inside
Rotating electrical machines –
Part 32: Measurement of stator end-winding vibration at form-wound windings

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]
CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC TS 60034-32 ®
Edition 1.0 2016-12
TECHNICAL
SPECIFICATION
colour
inside
Rotating electrical machines –

Part 32: Measurement of stator end-winding vibration at form-wound windings

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.160.01 ISBN 978-2-8322-3714-4

– 2 – IEC TS 60034-32:2016  IEC 2016
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 10
2 Normative references . 10
3 Terms, definitions and abbreviated terms . 11
3.1 Terms and definitions . 11
3.2 Abbreviated terms . 13
4 Causes and effects of stator end-winding vibrations . 14
5 Measurement of stator end-winding structural dynamics at standstill . 15
5.1 General . 15
5.2 Experimental modal analysis . 15
5.2.1 General . 15
5.2.2 Measurement equipment . 16
5.2.3 Measurement procedure . 17
5.2.4 Evaluation of measured frequency response functions, identification of
modes . 20
5.2.5 Elements of test report . 20
5.2.6 Interpretation of results . 21
5.3 Driving point analysis . 22
5.3.1 General . 22
5.3.2 Measurement equipment . 23
5.3.3 Measurement procedure . 23
5.3.4 Evaluation of measured FRFs, identification of modes . 23
5.3.5 Elements of test report . 24
5.3.6 Interpretation of results . 24
6 Measurement of end-winding vibration during operation . 25
6.1 General . 25
6.2 Measurement equipment . 25
6.2.1 General . 25
6.2.2 Vibration transducers . 26
6.2.3 Electro-optical converters for fiber optic systems . 27
6.2.4 Penetrations for hydrogen-cooled machines . 27
6.2.5 Data acquisition . 27
6.3 Sensor installation . 28
6.3.1 Sensor locations . 28
6.3.2 Good installation practices . 29
6.4 Most relevant dynamic characteristics to be retrieved . 30
6.5 Identification of operational deflection shapes . 31
6.6 Elements of test report . 31
6.7 Interpretation of results . 32
7 Repeated measurements for detection of structural changes . 33
7.1 General . 33
7.2 Reference measurements, operational parameters and their comparability . 33
7.3 Choice of measurement actions . 35
7.4 Aspects of machine’s condition and its history . 36
Annex A (informative) Background causes and effects of stator end-winding vibrations . 37

A.1 Stator end-winding dynamics . 37
A.1.1 Vibration modes and operating deflection shape . 37
A.1.2 Excitation of stator end-winding vibrations . 38
A.1.3 Relevant vibration characteristics of stator end-windings . 38
A.1.4 Influence of operational parameter . 41
A.2 Increased stator end-winding vibrations . 41
A.2.1 General aspects of increased vibration . 41
A.2.2 Increase of stator end-winding vibrations levels over time and potential
remedial actions . 42
A.2.3 Transient conditions as cause for structural changes . 43
A.2.4 Special aspects of main insulation . 44
A.3 Operational deflection shape of global stator end-winding vibrations . 44
A.3.1 General . 44
A.3.2 Force distributions relevant for global vibrational behaviour . 44
A.3.3 Idealized global vibration behaviour while in operation . 45
A.3.4 General vibration behaviour of stator end-windings . 47
A.3.5 Positioning of sensors for the measurement of global vibration level . 49
A.4 Operational deflection shape of local stator end-winding vibrations . 51
Annex B (informative) Data visualization . 52
B.1 General . 52
B.2 Standstill measurements . 53
B.3 Measurements during operation . 56
Bibliography . 62

Figure 1 – Stator end-winding of a turbogenerator (left) and a large motor (right) at
connection end with parallel rings . 7
Figure 2 – Example for an end-winding structure of an indirect cooled machine . 8
Figure 3 – Measurement structure with point numbering and indication of excitation . 19
Figure 4 – Simplified cause effect chain of stator end-winding vibration and influencing
operational parameters . 35
Figure A.1 – Illustration of global vibration modes . 40
Figure A.2 – Example of rotational force distribution for p = 1 . 45
Figure A.3 – Example of rotating operational vibration deflection wave for p = 1 . 46
Figure A.4 – Illustration of two vibration modes with different orientation in space
(example for p = 1) . 47
Figure A.5 – on-rotational operational vibration deflection wave (example for p = 1) . 48
Figure A.6 – Amplitude and phase distribution for a general case. . 49
Figure A.7 – Sensors for the measurement of global vibration level centred in the
winding zones . 50
Figure A.8 – Measurement of global vibration level with 6 equidistantly distributed
sensors in the centre of winding zones . 50
Figure A.9 – Example – Sensor positions for the measurement of local vibration level
of the winding connection relative to global vibration level . 51
Figure B.1 – Measurement structure with point numbering and indication of excitation . 52
Figure B.2 – Example for linearity test − Force signal and variance of related FRFs . 53
Figure B.3 – Example for reciprocity test – FRFs in comparison . 53
Figure B.4 – Example – Two overlay-plots of the same transfer functions but different
dimensions . 54

– 4 – IEC TS 60034-32:2016  IEC 2016
Figure B.5 – Shapes of the 4, 6 and 8-node modes with natural frequencies,
measurement in one plane . 55
Figure B.6 – Mode shape of a typical 4-node mode with different viewing directions
(stator end-winding and outer support ring) . 55
Figure B.7 – Example – Amplitude and phase of dynamic compliance and coherence . 56
Figure B.8 – 2-pole, 60 Hz generator – Trend in displacement over
...