IEC 62317-4:2005/COR1:2016
(Corrigendum)Corrigendum 1 - Ferrite cores - Dimensions - Part 4: RM-cores and associated parts
Corrigendum 1 - Ferrite cores - Dimensions - Part 4: RM-cores and associated parts
Corrigendum 1 - Noyaux ferrites - Dimensions - Partie 4: Noyaux RM et pièces associées
General Information
Relations
Standards Content (Sample)
IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 62317-4 IEC 62317-4
Edition 1.0 2005-09 Édition 1.0 2005-09
FERRITE CORES – DIMENSIONS – – NOYAUX FERRITES – DIMENSIONS –
Part 4: RM-cores and associated parts Partie 4: Noyaux RM et pièces associées
CO RRI G ENDU M 1
Table 1
...
This May Also Interest You
IEC 62024-1:2024 is available as IEC 62024-1:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62024-1:2024 specifies the electrical characteristics and measuring methods for the nanohenry range chip inductor that is normally used in the high frequency (over 100 kHz) range.
This edition includes the following significant technical changes with respect to the previous edition:
a) addition of S parameter measurement;
b) addition of the inductance, Q-factor and impedance of an inductor which are measured by the reflection coefficient method with a network analyzer;
c) addition of the resonance frequency of an inductor which is measured by a two-port network analyzer;
d) addition of the mounting method for a surface mounting inductor with Pb-free solder.
- Standard102 pagesEnglish languagesale 15% off
- Standard63 pagesEnglish and French languagesale 15% off
IEC 63093-13:2019 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PQ-cores and low-profile PQI-cores made of ferrite, and the locations of their terminal pins on a 2,54 mm printed wiring grid in relation to the base outlines of the cores. It also gives guidance on allowable limits of surface irregularities applicable to PQ-cores in accordance with the relevant generic specification.
This first edition cancels and replaces the second edition of IEC 62317-13 published in 2015 and the first edition of IEC 60424-8 published in 2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous editions of IEC 62317-13 and IEC 60424-8:
a) IEC 63093-13 integrates IEC 62317-13 and IEC 60424-8;
b) IEC 60424-8:2015, Table 1, has been included in Annex B as Table B.1.
- Standard2 pagesEnglish and French languagesale 15% off
IEC 62044-3:2023 is available as IEC 62044-3:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62044-3:2023 specifies measuring methods for power loss and amplitude permeability of magnetic cores forming the closed magnetic circuits intended for use at high excitation levels in inductors, chokes, transformers and similar devices for power electronics applications. This second edition cancels and replaces the first edition published in 2000. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: addition of Annex F and Annex G.
- Standard143 pagesEnglish languagesale 15% off
- Standard93 pagesEnglish and French languagesale 15% off
IEC 63300:2023 provides the test methods for the electrical and magnetic properties of magnetic powder cores used for inductive components in electronics equipment, switch-mode power supplies and power conversion equipment, and introduces measuring principles, scope of application and matters of importance for each method.
The parameters used to characterize the magnetic powder cores include: inductance factor, effective permeability, complex relative permeability, temperature coefficient of permeability, frequency coefficient of permeability, DC bias characteristic, power loss, and quality factor. This document is the basis for determining the characteristic parameters of magnetic powder cores.
- Standard111 pagesEnglish and French languagesale 15% off
IEC 63299:2022 specifies classification rules for metallic magnetic powder cores used in inductive components fulfilling the requirements of the electronics industries. This document addresses the following objectives for magnetic powder cores suppliers and users:
- cross-reference between core materials from multiple suppliers;
- assistance to users in understanding the published technical data in catalogues when comparing multiple suppliers;
- guidance to users in selecting the most applicable core for each application;
- establishing uniform benchmarks for suppliers for performance in the new development of core material.
- Standard23 pagesEnglish and French languagesale 15% off
IEC 63093-10:2022 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PM-cores made of magnetic oxides, the main dimensions for coil formers to be used with these cores and the locations of their pins on a modular printed wiring grid in relation to the base outlines of cores. It also specifies the effective parameter values to be used in calculations and gives guidelines on allowable limits of surface irregularities applicable to the PM-cores.
- Standard40 pagesEnglish and French languagesale 15% off
IEC 63182-3:2021 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of E-cores made of metallic magnetic powder, the essential dimensions of coil formers to be used with them as well as the effective parameter values to be used in calculations involving them, and gives guidelines on allowable limits of surface irregularities applicable to E-cores.
This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard24 pagesEnglish and French languagesale 15% off
IEC 63182-5:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives the guidelines on allowable limits of surface irregularities for cylinder-cores made of metallic magnetic powder.
This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard20 pagesEnglish and French languagesale 15% off
IEC 63182-4:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives guidelines on allowable limits of surface irregularities for block-cores made of metallic magnetic powder.
This document is a specification about surface irregularities which is useful in the negotiations between suppliers and users of magnetic powder-cores.
- Standard17 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.