IEC 61291-1:2012
(Main)Optical amplifiers - Part 1: Generic specification
Optical amplifiers - Part 1: Generic specification
IEC 61291-1:2012 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and waveguides (POWAs). This third edition cancels and replaces the second edition published in 2006. It is a technical revision that includes the following significant changes: the definitions related to transient behaviour have been extensively updated with terms from the 61290-4 series and the definition for gain ripple has been added.
Amplificateurs optiques - Partie 1: Spécification générique
La CEI 61291-1:2012 s'applique à tous les amplificateurs optiques (AO) et sous-ensembles à amplification optique, disponibles sur le marché. Elle s'applique aux AO utilisant des fibres pompées optiquement (AFO basés sur des fibres dopées aux terres rares ou sur l'effet Raman), des semiconducteurs (AOS), et des guides d'ondes (POWA). Cette troisième édition annule et remplace la deuxième édition publiée en 2006. Il s'agit d'une révision technique comprenant les modifications significatives suivantes: les définitions liées au comportement transitoire ont été mises à jour en profondeur avec des termes de la série 61290-4 et la définition relative à l'ondulation du gain a été ajoutée.
General Information
Relations
Standards Content (Sample)
IEC 61291-1 ®
Edition 3.0 2012-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical amplifiers –
Part 1: Generic Specification
Amplificateurs optiques –
Partie 1: Spécification générique
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC 61291-1 ®
Edition 3.0 2012-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical amplifiers –
Part 1: Generic Specification
Amplificateurs optiques –
Partie 1: Spécification générique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
V
CODE PRIX
ICS 33.180.20 ISBN 978-2-8322-0074-2
– 2 – 61291-1 © IEC:2012
CONTENTS
FOREWORD . 3
1 Scope and object . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
3.1 Overview . 6
3.2 Terms and definitions . 8
3.2.1 OA devices and distributed amplifiers . 8
3.2.2 OA-assemblies . 20
3.3 Abbreviated terms . 23
4 Classification . 24
5 Requirements . 25
5.1 Preferred values . 25
5.2 Sampling . 25
5.3 Product identification for storage and shipping . 25
5.3.1 Marking . 25
5.3.2 Labelling. 25
5.3.3 Packaging . 25
6 Quality assessment . 25
7 Electromagnetic compatibility (EMC) requirements . 25
8 Test methods . 26
Bibliography . 27
Index of definitions . 28
Figure 1 – OA device and assemblies . 7
Figure 2 – Optical amplifier in a multichannel application . 8
Table 1 – Grouping of parameters and corresponding test methods or references . 26
61291-1 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL AMPLIFIERS –
Part 1: Generic Specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61291-1 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This third edition cancels and replaces the second edition published in 2006. It is a technical
revision that includes the following significant changes: the definitions related to transient
behaviour have been extensively updated with terms from the 61290-4 series and the
definition for gain ripple has been added.
The text of this standard is based on the following documents:
CDV Report on voting
86C/1013/CDV 86C/1041/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
– 4 – 61291-1 © IEC:2012
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 61291 series, published under the general title Optical
amplifiers, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61291-1 © IEC:2012 – 5 –
OPTICAL AMPLIFIERS –
Part 1: Generic Specification
1 Scope and object
This part of IEC 61291 applies to all commercially available optical amplifiers (OAs) and
optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based
either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and
waveguides (POWAs). The object of this standard is:
– to establish uniform requirements for transmission, operation, reliability and environmental
properties of OAs;
– to provide assistance to the purchaser in the selection of consistently high-quality OA
products for his particular applications.
Parameters specified for OAs are those characterizing the transmission, operation, reliability
and environmental properties of the OA seen as a “black box” from a general point of view. In
the sectional and detail specifications a subset of these parameters will be specified
according to the type and application of the particular OA device or assembly.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.