IEC TS 62903:2023
(Main)Ultrasonics - Measurements of electroacoustical parameters and acoustic output power of spherically curved transducers using the self-reciprocity method
Ultrasonics - Measurements of electroacoustical parameters and acoustic output power of spherically curved transducers using the self-reciprocity method
IEC TS 62903:2023:
a ) establishes the free-field convergent spherical wave self-reciprocity method for ultrasonic transducer calibration,
b) establishes the measurement conditions and experimental procedure required to determine the transducer's electroacoustic parameters and acoustic output power using the self-reciprocity method,
c) establishes the criteria for checking the reciprocity of these transducers and the linear range of the focused field, and
d) provides guiding information for the assessment of the overall measurement uncertainties for radiation conductance.
This document is applicable to:
1) circular spherically curved concave focusing transducers without a centric hole working in the linear amplitude range,
2) measurements in the frequency range 0,5 MHz to 15 MHz, and
3) acoustic pressure amplitudes in the focused field within the linear amplitude range.
Characterization and sensitivity calibration of hydrophones using the reciprocity method are not addressed in this document but covered in IEC 62127-2 and IEC 60565-1.
IEC TS 62903:2023 cancels and replaces the first edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Several quantities are recognized as complex-valued quantities in the definitions and in the main text.
b) Annex I was added to provide typical measurement ranges and to provide example calibration results.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC TS 62903 ®
Edition 2.0 2023-06
TECHNICAL
SPECIFICATION
Ultrasonics – Measurements of electroacoustical parameters and acoustic
output power of spherically curved transducers using the self-reciprocity
method
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62903 ®
Edition 2.0 2023-06
TECHNICAL
SPECIFICATION
Ultrasonics – Measurements of electroacoustical parameters and acoustic
output power of spherically curved transducers using the self-reciprocity
method
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 17.140.50 ISBN 978-2-8322-7107-0
– 2 – IEC TS 62903:2023 IEC 2023
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Symbols . 13
5 General . 14
6 Requirements of the measurement system . 15
6.1 Apparatus configuration . 15
6.2 Measurement water tank . 15
6.3 Fixing, positioning and orientation systems . 15
6.4 Reflector . 15
6.5 Current monitor (probe) . 15
6.6 Oscilloscope . 16
6.7 Measurement hydrophone . 16
7 Measurement of the effective half-aperture of the spherically curved transducer . 16
7.1 Setup . 16
7.2 Alignment and positioning of the hydrophone in the field . 16
7.3 Measurements of the beamwidth and the effective half-aperture . 16
7.4 Calculations of the focus half-angle and the effective area . 17
8 Measurements of the electroacoustical parameters and the acoustic output power . 17
8.1 Self-reciprocity method for transducer calibration . 17
8.1.1 Experimental procedures . 17
8.1.2 Criterion for checking the linearity of the focused field . 17
8.1.3 Criterion for checking the reciprocity of the transducer . 18
8.2 Calculations of the transmitting response to current (voltage) and voltage
sensitivity . 18
8.3 Calculations of the transmitting response at geometric focus to current
(voltage) . 18
8.4 Calculation of the pulse-echo sensitivity level . 19
8.5 Measurements of the radiation conductance and the mechanical quality
factor Q . 19
m
8.5.1 Calculations of the acoustic output power and the radiation
conductance . 19
8.5.2 Measurement of the frequency response of the radiation conductance . 19
8.6 Measurement of the electroacoustic efficiency . 19
8.6.1 Calculation of the electric input power . 19
8.6.2 Calculation of the electroacoustic efficiency . 20
8.7 Measurement of the electric impedance (admittance) . 20
9 Measurement uncertainty . 20
Annex A (informative) Relation of the average amplitude reflection coefficient on a
plane interface of water-stainless steel and the focus half-angle for a normally
incident beam of a circular spherically curved transducer [6],[7] . 21
Annex B (informative) Diffraction correction coefficient G in the free-field self-
sf
reciprocity calibration method for circular spherically curved transducers in water
neglecting attenuation [7],[8],[9] . 25
Annex C (informative) Calculation of the diffraction correction coefficient G (R/λ,β) in
sf
the free-field self-reciprocity calibration in a non-attenuating medium for a circular
spherically curved transducer [7],[8],[9],[10] . 27
Annex D (informative) Speed of sound and attenuation in water. 30
D.1 General . 30
D.2 Speed of sound for propagation in water [14] . 30
D.3 Acoustic attenuation coefficient for propagation in water . 30
Annex E (informative) Principle of reciprocity calibration for spherically curved
transducers [7],[8],[9],[16],[17],[18],[19] . 32
E.1 Principle of reciprocity calibration for an ideal spherically focused field of a
transducer . 32
E.2 Principle of reciprocity calibration of a real spherically focused field of a
transducer . 33
E.3 Self-reciprocity calibration of a spherically curved transducer . 33
Annex F (informative) Experimental arrangements . 38
F.1 Experimental arrangement for determining the effective radius of a
transducer [7],[8],[9],[24] . 38
F.2 Experimental arrangement of the self-reciprocity calibration method for a
spherically curved transducer [8],[9],[24],[25] . 38
Annex G (informative) Relationships between the electroacoustical parameters used
in this application [24] . 40
G.1 Relationship between the free-field transmitting response to voltage
(current) and the voltage sensitivity with the radiation conductance . 40
G.2 Relationship between the radiation conductance and the electroacoustic
efficiency . 41
G.3 Relationship between the transmitting response and voltage and acoustic
output power . 41
G.4 Relationship between the pulse echo sensitivity and the radiation
conductance . 41
Annex H (informative) Evaluation and expression of uncertainty in the measurements
of the radiation conductance . 42
H.1 Executive standard . 42
H.2 Evaluation of uncertainty in the measurement of the radiation conductance . 42
H.2.1 Mathematical expression . 42
H.2.2 Type A evaluation of standard uncertainty . 42
H.2.3 Type B evaluation of standard uncertainty . 43
H.2.4 Evaluation of the combined standard uncertainty for the radiation
conductance . 45
Annex I (informative) Measurement range for power and pressure and examples of
electroacoustical parameters obtained . 49
I.1 Measurement range of acoustic pressure and power . 49
I.1.1 Lower limit of acoustic power . 49
I.1.2 Upper limit of pressure [27] . 49
I.2 Calibrated example of electroacoustical parameters . 50
I.2.1 1 MHz focusing transducer with air backing of diameter 80 mm and
focal length 200 mm . 50
I.2.2 5 MHz focusing transducer with air backing of diameter 20 mm and
focal length 20 mm . 51
Bibliography . 52
– 4 – IEC TS 62903:2023 IEC 2023
Figure A.1 – Relation curve of the amplitude reflection coefficient r(θ ) on the interface
i
of water-stainless steel for a plane wave with the incident angle θ . 23
i
Figure A.2 – Average amplitude reflection coefficient r (β) on the plane interface of
av
water-stainless steel in the geometric focal plane of a spherically curved transducer
plotted against the focus half-angle β . 24
Figure C.1 – Geometry of the concave radiating surface A of a spherically curved
transducer and its virtual image surface A′ for their symmetry of mirror-images about
the geometric focal plane (x,y,0) . 27
Figure E.1 – Spherical coordinates . 34
Figure E.2 – Function G (kasinθ), diffraction pattern F (kasinθ) and F (kasinθ) in the
a 0 0
geometric focal plane [10] . 35
Figure F.1 – Sch
...
IEC TS 62903 ®
Edition 2.0 2023-06
REDLINE VERSION
TECHNICAL
SPECIFICATION
colour
inside
Ultrasonics – Measurements of electroacoustical parameters and acoustic
output power of spherically curved transducers using the self-reciprocity
method
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62903 ®
Edition 2.0 2023-06
REDLINE VERSION
TECHNICAL
SPECIFICATION
colour
inside
Ultrasonics – Measurements of electroacoustical parameters and acoustic
output power of spherically curved transducers using the self-reciprocity
method
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 17.140.50 ISBN 978-2-8322-7137-7
– 2 – IEC TS 62903:2023 RLV IEC 2023
CONTENTS
FOREWORD . 5
INTRODUCTION . 2
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Symbols . 13
5 General . 15
6 Requirements of the measurement system . 15
6.1 Apparatus configuration . 15
6.2 Measurement water tank . 15
6.3 Fixturing Fixing, positioning and orientation systems. 16
6.4 Reflector . 16
6.5 Current monitor (probe) . 16
6.6 Oscilloscope . 16
6.7 Measurement hydrophone . 16
7 Measurement of the effective half-aperture of the spherically curved transducer . 17
7.1 Setup . 17
7.2 Alignment and positioning of the hydrophone in the field . 17
7.3 Measurements of the beamwidth and the effective half-aperture . 17
7.4 Calculations of the focus half-angle and the effective area . 17
8 Measurements of the electroacoustical parameters and the acoustic output power . 18
8.1 Self-reciprocity method for transducer calibration . 18
8.1.1 Experimental procedures . 18
8.1.2 Criterion for checking the linearity of the focused field . 18
8.1.3 Criterion for checking the reciprocity of the transducer . 18
8.2 Calculations of the transmitting response to current (voltage) and voltage
sensitivity . 18
8.3 Calculations of the transmitting response at geometric focus to current
(voltage) . 19
8.4 Calculation of the pulse-echo sensitivity level . 20
8.5 Measurements of the radiation conductance and the mechanical quality
factor Q . 20
m
8.5.1 Calculations of the acoustic output power and the radiation
conductance . 20
8.5.2 Measurement of the frequency response of the radiation conductance . 20
8.6 Measurement of the electroacoustic efficiency . 21
8.6.1 Calculation of the electric input power . 21
8.6.2 Calculation of the electroacoustic efficiency . 21
8.7 Measurement of the electric impedance (admittance) . 21
9 Measurement uncertainty . 21
Annex A (informative) Relation of the average amplitude reflection coefficient on a
plane interface of water-stainless steel and the focus half-angle for a normally incident
beam of a circular spherically curved transducer [6],[7] . 22
Annex B (informative) Diffraction correction coefficient G in the free-field self-
sf
reciprocity calibration method for circular spherically curved transducers in water
neglecting attenuation [7],[8],[9] . 27
Annex C (informative) Calculation of the diffraction correction coefficient G (R/λ,β) in
sf
the free-field self-reciprocity calibration in a non-attenuating medium for a circular
spherically curved transducer [7],[8],[9],[10] . 29
Annex D (informative) Speed of sound and attenuation in water. 32
D.1 General . 32
D.2 Speed of sound for propagation in water [14] . 32
D.3 Acoustic attenuation coefficient for propagation in water . 33
Annex E (informative) Principle of reciprocity calibration for spherically curved
transducers [7],[8],[9],[16],[17],[18],[19] . 34
E.1 Principle of reciprocity calibration for an ideal spherically focused field of a
transducer . 34
E.2 Principle of reciprocity calibration of a real spherically focused field of a
transducer . 35
E.3 Self-reciprocity calibration of a spherically curved transducer . 35
Annex F (informative) Experimental arrangements . 41
F.1 Experimental arrangement for determining the effective radius of a
transducer [7],[8],[9],[24] . 41
F.2 Experimental arrangement of the self-reciprocity calibration method for a
spherically curved transducer [8],[9],[24],[25] . 41
Annex G (informative) Relationships between the electroacoustical parameters used
in this application [24] . 43
G.1 Relationship between the free-field transmitting response to voltage
(current) and the voltage sensitivity with the radiation conductance . 43
G.2 Relationship between the radiation conductance and the electroacoustic
efficiency . 44
G.3 Relationship between the transmitting response and voltage and acoustic
output power . 44
G.4 Relationship between the pulse echo sensitivity and the radiation
conductance . 44
Annex H (informative) Evaluation and expression of uncertainty in the measurements
of the radiation conductance . 45
H.1 Executive standard . 45
H.2 Evaluation of uncertainty in the measurement of the radiation conductance . 45
H.2.1 Mathematical expression . 45
H.2.2 Type A evaluation of standard uncertainty . 45
H.2.3 Type B evaluation of standard uncertainty . 46
H.2.4 Evaluation of the combined standard uncertainty for the radiation
conductance . 49
Annex I (informative) Measurement range for power and pressure and examples of
electroacoustical parameters obtained . 52
I.1 Measurement range of acoustic pressure and power . 52
I.1.1 Lower limit of acoustic power . 52
I.1.2 Upper limit of pressure [27] . 52
I.2 Calibrated example of electroacoustical parameters . 53
I.2.1 1 MHz focusing transducer with air backing of diameter 80 mm and
focal length 200 mm . 53
I.2.2 5 MHz focusing transducer with air backing of diameter 20 mm and
focal length 20 mm . 54
Bibliography . 55
– 4 – IEC TS 62903:2023 RLV IEC 2023
Figure A.1 – Relation curve of the amplitude reflection coefficient r(θ ) on the interface
i
of water-stainless steel for a plane wave with the incident angle θ . 24
i
Figure A.2 – Average amplitude reflection coefficient r (β) on the plane interface of
av
water-stainless steel in the geometric focal plane of a spherically curved transducer
vs. plotted against the focus half-angle β . 26
Figure C.1 – Geometry of the concave radiating surface A of a spherically curved
transducer and its virtual image surface A′ for their symmetry of mirror-images about
the geometric focal plane (x,y,0) . 29
Figure E.1 – Spherical coordinates . 37
Figure E.2 – Function G (kasinθ), diffraction pattern F (kasinθ) and F (kasinθ) in the
a 0 0
geometric focal plane [10] . 38
Figure F.1 – Scheme of the measurement apparat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.