ISO/IEC 11695-3:2017

Identification cards — Optical memory cards — Holographic recording method — Part 3: Optical properties and characteristics

ISO/IEC 11695-3:2017 specifies the optical properties and characteristics of optical memory cards using the holographic recording method.

Cartes d'identification — Cartes à mémoire optique — Méthode d'enregistrement holographique — Partie 3: Propriétés et caractéristiques optiques

General Information

• Status: Published
• Publication Date: 26-Apr-2017
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 05-Sep-2022

Relations

• Revises: ISO/IEC 11695-3:2008 - Identification cards — Optical memory cards — Holographic recording method — Part 3: Optical properties and characteristics
• Effective Date: 09-Aug-2014

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 11695-3
Second edition
2017-04
Identification cards — Optical
memory cards — Holographic
recording method —
Part 3:
Optical properties and characteristics
Cartes d’identification — Cartes à mémoire optique — Méthode
d’enregistrement holographique —
Partie 3: Propriétés et caractéristiques optiques
Reference number
ISO/IEC 11695-3:2017(E)
©
ISO/IEC 2017

---------------------- Page: 1 ----------------------
ISO/IEC 11695-3:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO/IEC 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 11695-3:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Reading/writing test conditions . 2
4.1 Test methods . 2
4.2 Default test environment and conditioning . 2
5 Optical properties and characteristics . 2
5.1 Surface roughness/scattering . 2
5.2 Reflectivity of blank accessible optical area . 2
5.2.1 Spatial resolution . 2
Bibliography .3
© ISO/IEC 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 11695-3:2017(E)

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
The committee responsible for this document is ISO/IEC JTC 1, Information technology, SC 17, Cards and
personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 11695-3:2008), which has been
technically revised.
A list of all the parts in the ISO/IEC 11695 series can be found on the ISO website.
iv © ISO/IEC 2017 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 11695-3:2017(E)

Introduction
This document is one of a series of standards describing the parameters for optic
...