ISO/IEC 14543-5-22:2010
(Main)Information technology — Home electronic system (HES) architecture — Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Application profile — File profile
Information technology — Home electronic system (HES) architecture — Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Application profile — File profile
ISO/IEC 14543-5-22:2010(E) specifies the file data streaming application profile, device interaction flow model, the request and response messages in the device interaction process, and the service description format of the devices based on Intelligent Grouping and Resource Sharing (IGRS), ISO/IEC 14543-5-1. It is applicable to resource sharing and service collaboration of file data stream among computers, consumer electronics, and communication devices in a Local Area Network (LAN) or Personal Area Network (PAN) environment, especially in a wireless dynamic network.
Technologies de l'information — Architecture des systèmes électroniques domestiques (HES) — Partie 5-22: Groupage intelligent et partage des ressources pour HES, classe 2 et classe 3 — Profil d'application — Profil de fichier
General Information
Standards Content (Sample)
ISO/IEC 14543-5-22
Edition 1.0 2010-02
INTERNATIONAL
STANDARD
Information technology – Home electronic system (HES) architecture –
Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and
Class 3 – Application profile – File profile
ISO/IEC 14543-5-22:2010(E)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2010 ISO/IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about ISO/IEC copyright or have an enquiry about obtaining additional rights to this
publication, please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
---------------------- Page: 2 ----------------------
ISO/IEC 14543-5-22
Edition 1.0 2010-02
INTERNATIONAL
STANDARD
Information technology – Home electronic system (HES) architecture –
Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and
Class 3 – Application profile – File profile
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
V
ICS 35.200 ISBN 2-8318-1076-1
---------------------- Page: 3 ----------------------
– 2 – 14543-5-22 © ISO/IEC:2010(E)
CONTENTS
FOREWORD.4
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Abbreviations .6
4 Conformance.6
5 System .7
5.1 Application scenario .7
5.2 Design criteria .7
5.2.1 Relationship between file profile and IGRS .7
5.2.2 Relationship between file profile and transport protocols .7
5.2.3 Relationship between file profile and existing file sharing system .7
5.2.4 Relationship between file profile and file format.8
5.2.5 Device supported by file profile.8
5.3 Interaction model.8
6 Interaction flow of IGRS file profile .8
6.1 Overview .8
6.2 Simple Interaction Flow .9
6.3 Complete interaction flow .10
7 FileServer.13
7.1 General .13
7.2 FileAccessManagement Service .14
7.2.1 General .14
7.2.2 FileAccessManagement Service Type.14
7.2.3 FileAccessManagement Service Attribute .14
7.2.4 Data Types of FileAccessManagement Service.15
7.2.5 Invocation interface of FileAccessManagement Service.15
7.2.6 FileAccessManagement Service error codes definition .25
7.3 FileConnectionManagement Service.25
7.3.1 General .25
7.3.2 FileConnectionManagement Service Type .25
7.3.3 FileConnectionManagement Service Attribute.26
7.3.4 FileConnectionManagement Service Data Type.26
7.3.5 Invocation Interface of FileConnectionManagement Service .26
7.3.6 FileConnectionManagement Service error codes definition .28
8 FileClient.28
8.1 General .28
8.2 FileClient Engine .29
9 Session .29
9.1 Session setup.29
9.1.1 General .29
9.1.2 Session setup condition.29
9.1.3 Session setup process.29
9.2 Session termination.29
10 Service invocation message format .30
---------------------- Page: 4 ----------------------
14543-5-22 © ISO/IEC:2010(E) – 3 –
10.1 General .30
10.2 Service invocation request message .30
10.3 Service invocation response message.31
10.4 Content directory object update notification message .32
10.5 Service attribute update notification message.33
Annex A (normative) Description of data type generation rules .35
Annex B (normative) Information device – IGRS – File profile message format .38
Annex C (normative) File profile – FileAccessManagement Service description.wsdl .59
Annex D (normative) File profile – FileConnectionManagement Service
description.wsdl .69
Bibliography.72
Figure 1 – IGRS file profile interaction model.8
Figure 2 – Simple interaction flow model.10
Figure 3 – Complete Interaction Flow of Shared File.13
Table 1 – FileAccessManagement Service Attribute List .14
Table 2 – FileAccessManagement Service Data Type .15
Table 3 – FileConnectionManagement Service Attribute .26
Table 4 – FileConnectionManagement Service Data Type .26
Table 5 – Service invocation request message .30
Table 6 – Service invocation response message.31
Table 7 – Content directory object update notification message .32
Table 8 – Service attribute update notification message.34
Table B.1 – IGRS file profile service invocation request message .38
Table B.2 – Service invocation response message .39
Table B.3 – File/Directory object update notification message.40
Table B.4 – Service attribute update notification message .42
---------------------- Page: 5 ----------------------
– 4 – 14543-5-22 © ISO/IEC:2010(E)
INFORMATION TECHNOLOGY –
HOME ELECTRONIC SYSTEM (HES) ARCHITECTURE –
Part 5-22: Intelligent grouping and resource sharing for HES
Class 2 and Class 3 – Application profile – File profile
FOREWORD
1) ISO (International Organization for Standardization) and IEC (International Electrotechnical Commission) form the
specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in
the development of International Standards. Their preparation is entrusted to technical committees; any ISO and
IEC member body interested in the subject dealt with may participate in this preparatory work. International
governmental and non-governmental organizations liaising with ISO and IEC also participate in this preparation.
2) In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.
3) The formal decisions or agreements of IEC and ISO on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested IEC and ISO member bodies.
4) IEC, ISO and ISO/IEC publications have the form of recommendations for international use and are accepted
by IEC and ISO member bodies in that sense. While all reasonable efforts are made to ensure that the
technical content of IEC, ISO and ISO/IEC publications is accurate, IEC or ISO cannot be held responsible for
the way in which they are used or for any misinterpretation by any end user.
5) In order to promote international uniformity, IEC and ISO member bodies undertake to apply IEC, ISO and
ISO/IEC publications transparently to the maximum extent possible in their national and regional publications.
Any divergence between any ISO/IEC publication and the corresponding national or regional publication
should be clearly indicated in the latter.
6) ISO and IEC provide no marking procedure to indicate their approval and cannot be rendered responsible for
any equipment declared to be in conformity with an ISO/IEC publication.
7) All users should ensure that they have the latest edition of this publication.
8) No liability shall attach to IEC or ISO or its directors, employees, servants or agents including individual experts
and members of their technical committees and IEC or ISO member bodies for any personal injury, property
damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees)
and expenses arising out of the publication of, use of, or reliance upon, this ISO/IEC publication or any other IEC,
ISO or ISO/IEC publications.
9) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
10) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
International Standard ISO/IEC 14543-5-22 was prepared by subcommittee 25: Intercon-
nection of information technology equipment, of ISO/IEC joint technical committee 1:
Information technology.
The list of all currently available parts of ISO/IEC 14543 series, under the general title
Information technology – Home electronic system (HES) architecture, can be found on the
IEC web site.
This International Standard has been approved by vote of the member bodies, and the voting
results may be obtained from the address given on the second title page.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 6 ----------------------
14543-5-22 © ISO/IEC:2010(E) – 5 –
INTRODUCTION
ISO/IEC 14543-5, Intelligent Grouping and Resource Sharing for HES (IGRS), is divided into
seven parts:
¾ Part 5-1: Core protocol
• Specifies the TCP/IP protocol stack as the basis and the HTTP protocol as the
message-exchanging framework among devices.
• Defines a series of device and service interaction/invocation standards, including
device and service discovery protocol, device and service description, service
invocation, security mechanisms, etc.
• Specifies core protocols for a type of home network that supports streaming media
and other high-speed data transport within a home.
¾ Part 5-21: Application profile – AV profile
• Based on the IGRS Core Protocol.
• Defines a device and service interaction mechanism, as well as application interfaces
used in IGRS Basic Applications.
¾ Part 5-22: Application profile – File profile
• Based on the IGRS Core Protocol.
• Defines a device and service interaction mechanism, as well as application interfaces
used in IGRS Basic Applications.
¾ Part 5-3: Basic application
• Includes an IGRS basic application list.
• Defines a basic application framework.
• Addresses operation specifics (device grouping, service description template, etc.),
function definitions, and service invocation interfaces.
¾ Part 5-4: Device validation
• Defines a standard method to validate an IGRS-compliant device.
¾ Part 5-5: Device types
• Defines IGRS Device types used in IGRS applications.
¾ Part 5-6: Service types
• Defines basic service types used in IGRS applications.
---------------------- Page: 7 ----------------------
– 6 – 14543-5-22 © ISO/IEC:2010(E)
INFORMATION TECHNOLOGY –
HOME ELECTRONIC SYSTEM (HES) ARCHITECTURE –
Part 5-22: Intelligent grouping and resource sharing for HES
Class 2 and Class 3 – Application profile – File profile
1 Scope
This part of ISO/IEC 14543 specifies the file data streaming application profile, device
interaction flow model, the request and response messages in the device interaction process,
and the service description format of the devices based on Intelligent Grouping and Resource
Sharing (IGRS), ISO/IEC 14543-5-1.
This standard is applicable to resource sharing and service collaboration of file data stream
among computers, consumer electronics, and communication devices in a Local Area Network
(LAN) or Personal Area Network (PAN) environment, especially in a wireless dynamic network.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
The provisions of the referenced specifications other than ISO/IEC, IEC, ISO and ITU
documents, as identified in this clause, are valid within the context of this International
Standard. The reference to such a specification within this International Standard does not
give it any further status within ISO or IEC. In particular, it does not give the referenced
specification the status of an International Standard.
ISO/IEC 14543-5-1, Information technology – Home electronic system (HES) architecture –
Part 5-1: Intelligent grouping and resource sharing for Class 2 and Class 3 – Core protocol
W3C SOAP 1.2: Simple Object Access Protocol Version 1.2
http://www.w3.org/2002/12/soap-envelope
3 Abbreviations
For the purposes of this document the following acronyms and abbreviations apply.
FAMS FileAccessManagement Service
FC FileClient
FCMS FileConnectionManagement Service
FS FileServer
IGRS Intelligent grouping and resource sharing
4 Conformance
In order to conform to this International Standard the following applies.
• The IGRS File profile interaction model shall conform to the system specification
described in Clause 5.
---------------------- Page: 8 ----------------------
14543-5-22 © ISO/IEC:2010(E) – 7 –
• File service interaction flow models shall conform to the specifications described in
Clause 6.
• The relevant File device (File Server, File Client) and service (FAMS, FCMS) shall
conform to the specification defined in Clause 7 and Clause 8 r e s pec t i ve l y.
• The file invocation session setup procedure and message formats shall conform to
specifications defined in Clause 9 an d Clau se 10 .
5 System
5.1 Application scenario
In small office and home environment, there are many kinds of digital devices used, such as
PC, Notebook, PDA, DC, DV, MP3, MP4, mobile phone, Set-Top-Box, etc. Typically, the user
may need to browse, copy, delete, read and write data files stored in these devices over the
network.
File profile is designed specifically for this objective. It sets up a middleware layer between
the users and different devices. This layer hides the underlying networking protocols, devices,
operating systems and file operation modes while providing a set of commonly shared file
access APIs for the application program developers. The user can access the files in devices
transparently in a network environment, without having to consider the devices and operating
systems.
The file profile enables the client to access shared files on servers from different locations,
and it includes the following functions:
a) retrieve client file access identity verification;
b) browse shared file/directory on server;
c) manage uploading/downloading of file/directory;
d) support simple management of file/directory in the shared directory of FileServer;
e) support file/directory update event subscription on FileServer;
f) support service update event subscription;
g) out-of-band transport negotiation when uploading/downloading file.
5.2 Design criteria
5.2.1 Relationship between file profile and IGRS
File profile includes two parts: one specifies the functional interfaces of IGRS
FileAccessManagement service and FileConnectionManagement service; and the other
specifies the interaction logical flows of these service functional interfaces.
5.2.2 Relationship between file profile and transport protocols
File profile is a higher layer application profile in the IGRS framework and does not rely on
specific transport protocols. Therefore it shall support any transport protocols such as FTP,
HTTP, etc.
5.2.3 Relationship between file profile and existing file sharing system
File profile defines a set of standardized file sharing access interface based on IGRS network.
It does not put any restrictions on the backend implementation. File profile shall support either
private systems developed by users, or existing file sharing systems such as ActiveDirectory,
SMB, NFS, etc.
---------------------- Page: 9 ----------------------
– 8 – 14543-5-22 © ISO/IEC:2010(E)
5.2.4 Relationship between file profile and file format
File profile is independent of any specific file format, which means it shall support interactions
with files of any arbitrary format.
5.2.5 Device supported by file profile
Theoretically, file profile can run on any IGRS devices, such as PC, Notebook, PDA, DC, DV,
MP3, MP4, mobile phone, Set-Top-Box, etc.
5.3 Interaction model
IGRS file profile is composed of two logical devices, FileServer and FileClient. FileServer is a
device that provides content, and it includes two services: FileAccessManagement Service
(FAMS) and FileConnectionManagement Service (FCMS). FileClient is a device that accesses
content, and it includes FileClient Engine. The user can access and manage the contents
published by FileServer from FileClient. All interaction functions shall be completed though
the services and engine running on these devices.
The interaction model covers two services, FileAccessManagement Service and
FileConnectionManagement Service, both of which run on FileServer. FileAccessManagement
Service is responsible for a majority of functions in the file interaction framework, including
file browsing management, file uploading/downloading management, client access rights
authentication, etc. FileConnectionManagement Service is used in out-of-band transport
protocol negotiation between FileServer and FileClient. FileClient Engine is a client
application program responsible for interactions with FileServer. An IGRS file profile
interaction model is shown in Figure 1.
FileClient
FileServer
FileAccessManagement
FileClient Engine
Service
IGRS
Network
FileConnectionM anagement
Service
File Out-of-band Transport
Figure 1 – IGRS file profile interaction model
6 Interaction flow of IGRS file profile
6.1 Overview
Based on the basic rights setting of the shared files on FileServer, the interaction flow of
IGRS file profile can be classified into two categories: simple interaction flow (see 6.2) an d
complete interaction flow (see 5.3). In simple interaction flow, only the required interfaces of
---------------------- Page: 10 ----------------------
14543-5-22 © ISO/IEC:2010(E) – 9 –
FileAccessManagement Service and FileConnectionManagement Service on FileServer are
applicable in this process. FileClient can browse, download shared file and directory, or
retrieve attributes of shared file and directory. In complete interaction flow, the applicable
interfaces include all required interfaces of FileAccessManagement Service and
FileConnectionManagement Service on FileServer and any optional interfaces except for
those that relate to subscription. FileClient can perform management operations on shared
files and directories, such as copy, move, delete, modify attributes, etc., or upload file to
FileServer, in addition to browse, search, download shared file and directory, or retrieve
attributes of shared file and directory. The detailed descriptions about services and interfaces
in interaction flow can be found in A nne x B .
6.2 Simple Interaction Flow
In simple interaction flow (see Figure 2), only the required interfaces of
FileAccessManagement Service and FileConnectionManagement Service on FileServer are
applicable. The FileClient shall access a shared file and directory in read-only mode, and is
allowed to browse, download a shared file/directory or retrieve attributes of a shared
file/directory. However, it shall not be allowed to modify a shared file/directory.
In a simple interaction flow, the invocation process of IGRS service interfaces between
FileClient and FileServer is described as follows.
a) IGRS service discovery: through IGRS service discovery mechanism, FileClient discovers
FileAccessManagement Service and FileConnectionManagement Service on FileServer.
b) Retrieve access right: a FileClient retrieves an authentication key to get an access right to
a shared file on FileServer through invoking FAMS::GetAuthenticationKey() interface of
FileAccessManagement Service on FileServer. FileClient can use any combination
information of DeviceID/DeviceName, UserName/Password, and Third-party
authentication mode of the local device, to retrieve authentication key from FileServer.
c) Browse a shared file/directory:
1) Retrieve sorting capability of a FileServer: a FileClient can retrieve a shared
file/directory sorting capability of a FileServer by invoking
FAMS::GetSortCapability() interface of FileAccessManagement Service on the
FileServer. For example, it can sort according to file names or the time of
modification.
2) Browse a shared file/directory on a FileServer: a FileClient can browse all the
files and sub-directory information in any specified shared directory by invoking
FAMS::Browse() interface of FileAccessManagement Service on FileServer.
3) Retrieve attributes of a shared file/directory: a FileClient can retrieve attributes
of any specified shared file/directory by invoking FAMS::GetAttribute() interface
of FileAccessManagement Service on a FileServer.
d) Setup a connection with a FileServer:
1) Retrieve transport protocols supported by a FileServer: a FileClient retrieves
transport protocols supported by a FileServer, by invoking
FCMS::GetProtocolInfo() interface of FileconnectionManagement Service on a
FileServer.
2) Select matching transport protocols: the use of retrieved transport protocols
supported by a FileServer according to 1) in step d), a FileClient selects
matching transport protocols supported by the device.
3) Connection preparation: a FileClient notifies a FileServer to prepare for a
connection setup, and retrieve the connection identifier for connection
management to be used in a subsequent interaction process, by invoking
FCMS::PrepareforConnection() interface of a FileConnectionManagement
Service on a FileServer.
e) Download a shared file/directory from a FileServer: a FileClient can set up the
downloading of a shared file/directory, and retrieve the URI list of a downloaded shared
---------------------- Page: 11 ----------------------
– 10 – 14543-5-22 © ISO/IEC:2010(E)
file/directory from a FileServer, by invoking FAMS::PrepareforDownload() interface of a
FileAccessManagement Service on a FileServer.
f) File/directory transport: a FileClient and FileServer use out-of-band transport protocols
and the URI retrieved in step e) to transport data. When the specified file/directory has
been transported, it goes to back to step e) to transport another file/directory if required.
g) Close connection and release resource: when the file transport has been completed, the
FileClient notifies the FileServer to close the connection between them and release the
resource, by invoking FCMS::ReleaseConnection() interface of FileConnection-
Management Service on FileServer.
Figure 2 – Simple interaction flow model
6.3 Complete interaction flow
In a complete interaction flow (see Figure 3), the applicable interfaces include all required
interfaces of the FileAccessManagement Service and FileConnectionManagement Service on
a FileServer and any optional interfaces except for those that relate to subscription. A
FileClient can perform management operations on shared files and directories, such as copy,
move, delete, modify attributes, etc., or upload a file to a FileServer, in addition to browse,
---------------------- Page: 12 ----------------------
14543-5-22 © ISO/IEC:2010(E) – 11 –
search and download a shared file and directory, or retrieve attributes of a shared file and
directory.
In a complete interaction flow, the invocation process of IGRS service interfaces between a
FileCl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.