Thermal insulating products for building applications — Determination of short-term water absorption by partial immersion

ISO 29767:2008 specifies the equipment and procedures for determining the short-term water absorption of specimens by partial immersion. ISO 29767:2008 is applicable to thermal insulating products.

Produits isolants thermiques destinés aux applications du bâtiment — Détermination de l'absorption d'eau à court terme par immersion partielle

General Information

Status
Withdrawn
Publication Date
28-Oct-2008
Withdrawal Date
28-Oct-2008
Current Stage
9599 - Withdrawal of International Standard
Start Date
27-Jun-2019
Completion Date
27-Jun-2019
Ref Project

RELATIONS

Buy Standard

Standard
ISO 29767:2008 - Thermal insulating products for building applications -- Determination of short-term water absorption by partial immersion
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 29767
First edition
2008-11-01
Thermal insulating products for building
applications — Determination of short-
term water absorption by partial
immersion
Produits isolants thermiques destinés aux applications du bâtiment —
Détermination de l'absorption d'eau à court terme par immersion
partielle
Reference number
ISO 29767:2008(E)
ISO 2008
---------------------- Page: 1 ----------------------
ISO 29767:2008(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2008

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 29767:2008(E)
Contents Page

Foreword............................................................................................................................................................ iv

Introduction ........................................................................................................................................................ v

1 Scope ..................................................................................................................................................... 1

2 Normative references ........................................................................................................................... 1

3 Principle................................................................................................................................................. 1

4 Apparatus .............................................................................................................................................. 1

5 Test specimens ..................................................................................................................................... 3

6 Procedure .............................................................................................................................................. 3

7 Calculation and expression of results................................................................................................ 5

8 Accuracy of measurement................................................................................................................... 5

9 Test report ............................................................................................................................................. 6

© ISO 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 29767:2008(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 29767 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the

built environment, Subcommittee SC 1, Test and measurement methods.
iv © ISO 2008 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 29767:2008(E)
Introduction

This International Standard comprises the original EN 1609:1996, EN 1609:1996/AC:1997 and its

Amendment 1:2006 prepared by Technical Committee CEN/TC 88, Thermal insulating materials and products,

which have been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in

tropical countries.

This International Standard is one of a series of documents specifying test methods, based on existing

European Standards, that are being adopted by ISO. This “package” of standards includes the following group

of interrelated documents.
International Standard Respective
EN standard

ISO 29465, Thermal insulating products for building applications — Determination of length EN 822

and width

ISO 29466, Thermal insulating products for building applications — Determination of EN 823

thickness

ISO 29467, Thermal insulating products for building applications — Determination of EN 824

squareness

ISO 29468, Thermal insulating products for building applications — Determination of flatness EN 825

ISO 29469, Thermal insulating products for building applications — Determination of EN 826

compression behaviour

ISO 29470, Thermal insulating products for building applications — Determination of the EN 1602

apparent density

ISO 29471, Thermal insulating products for building applications — Determination of EN 1603

dimensional stability under constant normal laboratory conditions (23 °C/50 % relative

humidity)

ISO 29472, Thermal insulating products for building applications — Determination of EN 1604

dimensional stability under specified temperature and humidity conditions

ISO 29764, Thermal insulating products for building applications — Determination of EN 1605

deformation under specified compressive load and temperature conditions

ISO 29765, Thermal insulating products for building applications — Determination of tensile EN 1607

strength perpendicular to faces

ISO 29766, Thermal insulating products for building applications — Determination of tensile EN 1608

strength parallel to faces

ISO 29767, Thermal insulating products for building applications — Determination of short- EN 1609

term water absorption by partial immersion
© ISO 2008 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO 29767:2008(E)

ISO 29768, Thermal insulating products for building applications — Determination of linear EN 12085

dimensions of test specimens

ISO 29769, Thermal insulating products for building applications — Determination of EN 12430

behaviour under point load

ISO 29770, Thermal insulating products for building applications — Determination of EN 12431

thickness for floating-floor insulating products

ISO 29771, Thermal insulating materials for building applications — Determination of organic EN 13820

content

ISO 29803, Thermal insulation products for building applications — Determination of the EN 13497

resistance to impact of external thermal insulation composite systems (ETICS)

ISO 29804, Thermal insulation products for building applications — Determination of the EN 13494

tensile bond strength of the adhesive and of the base coat to the thermal insulation material

ISO 29805, Thermal insulation products for building applications — Determination of the EN 13496

mechanical properties of glass fibre meshes
vi © ISO 2008 – All rights reserved
---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 29767:2008(E)
Thermal insulating products for building applications —
Determination of short-term water absorption by partial
immersion
1 Scope

This International Standard specifies the equipment and procedures for determining the short-term water

absorption of specimens by partial immersion. This International Standard is applicable to thermal insulating

products.

NOTE The procedure specified by this International Standard is intended to simulate the water absorption caused by

a 24 h raining period during construction work.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the editio
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.