91.100.60 - Thermal and sound insulating materials
ICS 91.100.60 Details
Thermal and sound insulating materials
Isolierstoffe. Dammstoffe
Matériaux d'isolation thermique et acoustique
Materiali za toplotno in zvočno izolacijo
General Information
This document specifies the requirements for factory-made aerogel blankets, which are used for the thermal insulation of building applications. This document specifies insulation that exhibits thermal insulating performance through high porosity and nano-sized pores by compounding aerogel with net-like fibrous material, e.g. polyester, glass fibre, ceramic fibre. The products are delivered as a blanket type. This document describes product characteristics and includes procedures for testing, evaluation of conformity and marking and labelling. This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application.Â
- Standard14 pagesEnglish languagesale 15% off
- Draft14 pagesEnglish languagesale 15% off
This European Standard specifies the equipment and procedure for determining the resistance to impact of design ETICS kits with renders.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This draft European Standard specifies the requirements for factory made calcium silicate products with or without lamination or coating which are used for the thermal insulation of buildings.
Calcium silicate products have also the capability to regulate air moisture in building rooms, which means to absorb moisture from the air and opposite to give the moisture back to the room due to the capillarity of the product.
Calcium silicate insulation material comprising hydrated calcium silicate, normally reinforced by incorporated fibres. The main crystal phases are Xonotlite, Tobermorite with or without Wollastonite.
The products are manufactured in the form of boards, segments and prefabricated ware.
This draft European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
This draft European Standard does not specify the required level or class of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
This draft European Standard is not valid for products with declared thermal resistance lower than 0,13 m2 K/W or a declared thermal conductivity greater than 0,075 W/(mK) at 10 °C.
This draft European Standard does not cover aerated concrete, autoclaved aerated concrete, mineral foam insulating products and sand-lime bricks as well as in situ insulation products and products intended to be used for the insulation of the building equipment and industrial installations.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
This standard defines requirements for factory made Vacuum Insulation Panels (VIP), which are used for the thermal insulation of buildings. This standard describes the product properties and contains test methods and rules for conformity evaluations, identification and labelling. The determination of VIP properties influencing the service life time and VIP performance is content of this standard as well. The standard provides a test method to determine the ageing of the product including the influence of the linear thermal bridges at the edges.
This standard is applicable for all types of VIP independent of the core material or type of envelope. It is also applicable for VIP using desiccants but not getters, due to a lack of experience with ageing of these panels.
This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
Products with a declared thermal resistance RD lower than 0,5 m2 K/W or a declared thermal conductivity λD according to Annex C of this Standard greater than 0,015 W/(m⋅K) are not covered by this standard.
This standard does not cover products intended to be used for the insulation of building equipment and industrial installations.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies an alternating airflow method for the determination of the airflow resistance[1] [2] of porous materials for acoustical applications.
Determination of the airflow resistance based on static flow is described in ISO 9053-1.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an alternating airflow method for the determination of the airflow resistance[5], [6] of porous materials for acoustical applications. Determination of the airflow resistance based on static flow is described in ISO 9053‑1.
- Standard20 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This Standard is applicable to full size thermal insulating products and test specimens. This standard can also be applied to the individual layers of multi layered products. It specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the equipment and test method for determining the effects of successive cycling from dry conditions at 20 °C to wet conditions at 20 °C on the mechanical properties and moisture content of the product. It is applicable to thermal insulating products.
The propose of this document is to simulate the freeze–thaw effects on thermal insulating products which are frequently exposed to water and low temperature conditions, e.g. inverted roofs and unprotected ground insulation.
The test is to be performed continuously using an automatic process of cycling between the specified conditions.
This test method is not recommended for all thermal insulating products. If relevant, the product standards will state for which products this International Standard is applicable.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the equipment and test method for determining the compressive creep of specimens under various conditions of stress.
This document is applicable to thermal insulating products.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the equipment and test method for determining the compressive creep of specimens under various conditions of stress. This document is applicable to thermal insulating products.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
- Draft16 pagesEnglish languagesale 15% off
This document specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. This document is applicable to full size thermal insulating products and test specimens. This document can also be applied to the individual layers of multi‑layered products.
- Standard4 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Draft4 pagesEnglish languagesale 15% off
This document specifies the equipment and test method for determining the effects of successive cycling from dry conditions at −20 °C to wet conditions at 20 °C on the mechanical properties and moisture content of thermal insulating products. This document is intended to simulate the freeze?thaw effects on thermal insulating products which are frequently exposed to water and low temperature conditions, e.g. inverted roofs and unprotected ground insulation.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Draft7 pagesEnglish languagesale 15% off
ISO 4898:2018 specifies requirements and methods of testing for three categories of rigid cellular plastics thermal-insulation products for buildings. It covers rigid cellular plastics in the form of flat or profiled boards, with or without natural skins. They can also be faced or laminated with foil, plastic or metal films or sheets, mineral coatings, paper, cardboard or other materials.
ISO 4898:2018 is not applicable to materials used for the thermal insulation of pipes and vessels, for impact sound absorption or for acoustical insulation.
ISO 4898:2018 covers the following cellular materials used in the thermal insulation of buildings:
- PF based on phenolic polymer;
- EPS based on expanded polystyrene;
- XPS based on extruded polystyrene;
- PUR based on polyurethane.
The limiting quality values in this document are for use only in the specification of materials between purchaser and supplier, and are not intended to be used for design purposes.
Additional requirements for special applications can be added to those specified in this document by agreement between purchaser and supplier.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesEnglish languagesale 15% off
This document specifies test methods for the evaluation of the mechanical properties for moisture curing, self-curing activatable or water drying foams dispensed from single pressurized foam containers.
This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
The following test methods are described:
- Method 1 - Compression strength: This test method describes how to determine the compressive strength of a cured foam. It gives an indication of the foams resistance against area distributed pressure. The maximum endurable stress is determined.
- Method 2 - Movement capability: This test method describes how to determine the movement capability of cured foam. The result gives an indication of the degree of flexibility of the cured foam.
- Method 3 - Bonding strength: The method displays the measurement of the bonding power of a One Component (Foam) Adhesive, dispensed from a pressurized foam container, between two substrates with direct contact.
- Method 4 - Tensile strength: This test method describes how to determine the maximum stress a cured foam can withstand while being stretched before breaking. The result gives an indication of the elasticity of the cured foam.
- Method 5 - Shear strength: This method displays the behaviour of a foam system towards shear forces. It shows the strength and the bonding power of the foam as the sandwich element between wooden plates. The test is conducted according to EN 12090.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for products of loose-filled expanded polystyrene (EPS) beads and bonded expanded polystyrene beads for in-situ installation in masonry cavity walls and frame constructions.
This document is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling.
This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
NOTE To avoid water penetration in masonry walls special tests adjusted to local climate might be needed.
This document does not cover factory made expanded polystyrene (EPS) insulation products or factory made or in-situ products intended to be used for the insulation of building equipment and industrial installations.
Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this document.
This document does not cover products intended for airborne sound insulation and for acoustic absorption applications.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for products of loose-filled expanded polystyrene (EPS) beads and bonded expanded polystyrene beads for in-situ installation in masonry cavity walls and frame constructions.
This document is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling.
This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
NOTE To avoid water penetration in masonry walls special tests adjusted to local climate might be needed.
This document does not cover factory made expanded polystyrene (EPS) insulation products or factory made or in-situ products intended to be used for the insulation of building equipment and industrial installations.
Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this document.
This document does not cover products intended for airborne sound insulation and for acoustic absorption applications.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies equipment and procedures for determining the resistance of kits out of external thermal insulation composite systems (ETICS) to tension and/or shear forces.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the equipment and procedures for determining the tensile bond strength of an adhesive or a base coat (as a component of External Thermal Insulation Composite Systems) to a thermal insulation product.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies the equipment and procedures for determining the long term water absorption of test specimens by diffusion. It is applicable to thermal insulating products. It is intended to simulate the water absorption of products subjected to high relative humidities, approximating to 100 %, on both sides and subjected to a water vapour pressure gradient for a long period of time e.g. inverted roof or unprotected ground insulation.
The test is not applicable for all types of thermal insulating products. The product standard should state for which of its products, if any, this test is applicable.
NOTE For unprotected ground insulation the temperature of 50 °C may be replaced by a lower temperature, when more data is available.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies the equipment and procedures for determining the long term water absorption of test specimens. It is applicable to thermal insulating products.
This International Standard specifies two options:
- Method 1 - partial immersion
- Method 2 - total immersion
The long term water absorption by partial immersion is intended to simulate the water absorption caused by long term water exposure.
The long term water absorption by total immersion is not directly related to the conditions on site, but has been recognized as a relevant condition of test for some products in some applications.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies the equipment and procedures for determining the short-term water absorption of specimens by partial immersion. It is applicable to thermal insulating products.
NOTE It is intended to simulate the water absorption caused by a 24 h raining period during construction work.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesGerman languagesale 10% offe-Library read for1 day
This document specifies equipment and procedures for determining the load-bearing capability ("pull-off") of kits out of external thermal insulation composite systems (ETICS) to tension and/or shear forces.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the test apparatus, materials and procedures for determining the tensile bond strength of an adhesive, a reinforced base coat or a rendering system to a thermal insulation product for use as components in External Thermal Insulation Composite Systems.
The test method described in this document is not applicable to PU foam adhesives. For testing such products see EN 17101.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for the installation of exterior insulation and finish systems (EIFS) for wall applications using material which meet the materials requirements of ISO 17738‑1 and the design requirements of ISO 17738‑3. This document further includes installation requirements for the EIFS materials that include a water resistive barrier (WRB) and decorative projections as part of the cladding system for walls. This document does not include requirements for the structural design of the substrate/building structural members or for the integrity of the substrate/building structural members to which the EIFS is to be attached, nor the requirements for installation or repair of the substrate/building structural members before installation commences. This document does not include requirements for the competence that an EIFS installer needs for installation of the system. The installation of EIFS on horizontal surfaces exposed to direct precipitation is outside the scope of this document.
- Standard20 pagesEnglish languagesale 15% off
This document specifies the design requirements, selection and application of exterior insulation and finish systems (EIFS) for use by building designers, building code officials, product manufacturers and contractors in order to sustain the installed performance and durability of EIFS. NOTE This document does not address all aspects related to EIFS design, selection and use. A working knowledge of applicable regional building codes and regulations is helpful when working with this document. There could be other considerations for specific installations that are not addressed by this document. This document contains design requirements for the design and installation of an EIFS as a wall cladding system. The document includes selection of materials that meet the requirements of ISO 17738‑1, and installation requirements in accordance with ISO 17738‑2 and covers the interfaces between EIFS and other building assemblies and components. This document refers to adhesively fastened systems, although mechanical fastening could be required in specific circumstances (refer to Annex A). For information on EIFS resiliency, refer to Annex B. This document does not specify the structural design of the substrate to which the EIFS is attached, nor does it provide design requirements when the installation of EIFS uses mechanical fasteners. This document is applicable to new and retrofit EIFS installations.
- Standard12 pagesEnglish languagesale 15% off
This document specifies the equipment and procedures for determining the short‑term water absorption of specimens by partial immersion. It is applicable to thermal insulating products.
NOTE It is intended to simulate the water absorption caused by a 24 h raining period during construction work.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesGerman languagesale 10% offe-Library read for1 day
This document specifies the equipment and procedures for determining the long-term water absorption of test specimens by diffusion. It is applicable to thermal insulating products. It is intended to simulate the water absorption of products subjected to high relative humidities, approximating to 100 %, on both sides and subjected to a water vapour pressure gradient for a long period of time e.g. inverted roof or unprotected ground insulation.
The test is not applicable for all types of thermal insulating products. The relevant product standard should state for which of its products, if any, this test is applicable.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the equipment and procedures for determining the long-term water absorption of test specimens. It is applicable to thermal insulating products.
This document specifies two methods:
— Method 1: Partial immersion;
— Method 2: Total immersion.
The long-term water absorption by partial immersion is intended to simulate the water absorption caused by long-term water exposure.
The long-term water absorption by total immersion is not directly related to the conditions on site, but has been recognized as a relevant condition of test for some products in some applications.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the equipment and procedures for determining the long-term water absorption of test specimens by diffusion. It is applicable to thermal insulating products. It is intended to simulate the water absorption of products subjected to high relative humidities, approximating to 100 %, on both sides and subjected to a water vapour pressure gradient for a long period of time e.g. inverted roof or unprotected ground insulation. The test is not applicable for all types of thermal insulating products. The relevant product standard should state for which of its products, if any, this test is applicable.
- Standard4 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
This document specifies the equipment and procedures for determining the short‑term water absorption of specimens by partial immersion. It is applicable to thermal insulating products. NOTE It is intended to simulate the water absorption caused by a 24 h raining period during construction work.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies the equipment and procedures for determining the long-term water absorption of test specimens. It is applicable to thermal insulating products. This document specifies two methods: — Method 1: Partial immersion; — Method 2: Total immersion. The long-term water absorption by partial immersion is intended to simulate the water absorption caused by long-term water exposure. The long-term water absorption by total immersion is not directly related to the conditions on site, but has been recognized as a relevant condition of test for some products in some applications.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
This European Standard specifies requirements for loose-fill cellulose insulation (LFCI) products for the thermal and/or sound insulation of buildings when installed into walls, floors, galleries, roofs and ceilings.
This European Standard is a specification for the loose-fill cellulose insulation (LFCI) products before installation.
This European Standard describes the product characteristics and includes procedures for testing, marking and labelling and the rules for evaluation of conformity.
Products covered by this European Standard may also be used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered.
Products with a declared thermal conductivity at 10 °C greater than 0,060 W/(m K) or a declared thermal resistance lower than 0,25 m2 K/W are not covered by this European Standard.
This European Standard does not specify the required level of all properties to be achieved by a product to demonstrate fitness for purpose in a particular application. The required levels are to be found in local regulations or non-conflicting standards.
This European Standard does not cover factory made cellulose products placed on the market as bats, mats or boards intended to be used for the insulation of buildings or loose-fill cellulose products for the insulation of building equipment and industrial installations.
- Standard66 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for loose-fill cellulose insulation (LFCI) products for the thermal and/or sound insulation of buildings when installed into walls, floors, galleries, roofs and ceilings.
This European Standard is a specification for the loose-fill cellulose insulation (LFCI) products before installation.
This European Standard describes the product characteristics and includes procedures for testing, marking and labelling and the rules for evaluation of conformity.
Products covered by this European Standard may also be used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered.
Products with a declared thermal conductivity at 10 °C greater than 0,060 W/(m K) or a declared thermal resistance lower than 0,25 m2 K/W are not covered by this European Standard.
This European Standard does not specify the required level of all properties to be achieved by a product to demonstrate fitness for purpose in a particular application. The required levels are to be found in local regulations or non-conflicting standards.
This European Standard does not cover factory made cellulose products placed on the market as bats, mats or boards intended to be used for the insulation of buildings or loose-fill cellulose products for the insulation of building equipment and industrial installations.
- Standard66 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the measurement of the determination of the static airflow resistance[1,2], in a
laminar flow regime, of porous materials for acoustical applications.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Report specifies a method for the determination of ammonia from cellulose insulation products at 90% relative humidity (RH).
This document is based on the existing prEN 16516 standard which provides an horizontal reference method for the determination of emissions of regulated dangerous substances from construction products into indoor air.
- Technical report20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the measurement of the determination of the static airflow resistance[1,2], in a laminar flow regime, of porous materials for acoustical applications.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for blown and injected loose-fill mineral wool products for in-situ installation in lofts, masonry cavity walls and frame constructions.
This European Standard is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling.
This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
NOTE To avoid water penetration in masonry walls special tests adjusted to local climate might be needed.
This document does not cover factory made mineral wool (MW) insulation products or in-situ products intended to be used for the insulation of building equipment and industrial installations.
Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this document.
This document does not cover products intended for airborne sound insulation and for acoustic absorption applications.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Report specifies a method for the determination of ammonia from cellulose insulation products at 90% relative humidity (RH).
This document is based on the existing prEN 16516 standard which provides an horizontal reference method for the determination of emissions of regulated dangerous substances from construction products into indoor air.
- Technical report20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the measurement of the determination of the static airflow resistance[1,2], in a laminar flow regime, of porous materials for acoustical applications.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
This document specifies the requirements for blown and injected loose-fill mineral wool products for in situ installation in lofts, masonry cavity walls and frame constructions.
This document is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling.
This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
NOTE To avoid water penetration in masonry walls special tests adjusted to local climate might be needed.
This document does not cover factory made mineral wool (MW) insulation products or in situ products intended to be used for the insulation of building equipment and industrial installations.
Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this document.
This document does not cover products intended for airborne sound insulation and for acoustic absorption applications.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies methods of identification and test methods for the performance evaluation of one-component PU foams used as adhesive according to the ETICS specification (see WI 00088330).
Other foams are not covered by this European Standard.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods of identification and test methods for the performance evaluation of one-component PU foams used as adhesive foam.
Other foams are not covered by this document.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the classification, requirements and test methods for factory-made aluminosilicate wool products which are used for thermal insulation of industrial installations and building equipment, for non-refractory applications. The products are delivered as blanket, module, felt, board, paper, textile and other forms. This document describes product characteristics and testing methods, marking and labelling. This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application.
- Standard11 pagesEnglish languagesale 15% off
This document specifies requirements for factory-made products of sheep wool, which are used for the thermal insulation of buildings. This document applies to material containing more than 50 % (by mass) natural sheep wool, with the balance being polymeric material. The products are delivered as a mat or board with or without facings. This document describes product characteristics and testing methods, marking, labelling and packaging. Products covered in this document are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. The sheep wool mat and board thermal insulation is not to be used when the continuous service temperature of the substrate is outside the range of −60 °C to +80 °C. The use of mothproof agent residues is outside the scope of this document. This document does not address all the health and safety aspects associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices.
- Standard17 pagesEnglish languagesale 15% off
ISO 4898:2018 specifies requirements and methods of testing for three categories of rigid cellular plastics thermal-insulation products for buildings. It covers rigid cellular plastics in the form of flat or profiled boards, with or without natural skins. They can also be faced or laminated with foil, plastic or metal films or sheets, mineral coatings, paper, cardboard or other materials. ISO 4898:2018 is not applicable to materials used for the thermal insulation of pipes and vessels, for impact sound absorption or for acoustical insulation. ISO 4898:2018 covers the following cellular materials used in the thermal insulation of buildings: - PF based on phenolic polymer; - EPS based on expanded polystyrene; - XPS based on extruded polystyrene; - PUR based on polyurethane. The limiting quality values in this document are for use only in the specification of materials between purchaser and supplier, and are not intended to be used for design purposes. Additional requirements for special applications can be added to those specified in this document by agreement between purchaser and supplier.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesEnglish languagesale 15% off
This European Standard specifies the equipment and procedures for determining the dimensions, squareness and linearity of preformed pipe insulation, supplied in one piece, half sections or segments. It is applicable to thermal insulating products.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the equipment and procedures for determining the dimensions, squareness and linearity of preformed pipe insulation, supplied in one piece, half sections or segments. It is applicable to thermal insulating products.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies the characteristics and performances of gypsum based adhesives which are composed of gypsum plasters defined in EN 13279 1 and of additives. These adhesives are used for fixing to walls and partitions, gypsum board thermal/acoustic insulation composite panels according to EN 13950, gypsum plasterboard linings according to EN 520, gypsum boards with mat reinforcement according to EN 15283 1, gypsum fibre boards according to EN 15283 2 and other suitable products as reprocessed boards according to EN 14190 and cornices according to EN 14209. They assist in the construction of systems which provide thermal and acoustic performance.
It covers the following performance characteristics: reaction to fire, fire resistance and bond strength to be measured according to the corresponding European test methods.
It provides the assessment and verification of constancy of performance of the products.”
This standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction Industry and the reference tests for these characteristics.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for expanded polystyrene (EPS) beads and the adhesive, which are after installation used for the thermal insulation of buildings. The EPS beads and the adhesive are mixed and processed on site.
This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
This standard does not cover factory made insulation products in the form of prefabricated shapes or boards made of bonded EPS beads.
Products with a declared thermal resistance lower than 0,25 (m² x K)/W or a declared thermal conductivity at 10 °C greater than 0,1 W/(m x K) are not covered by this standard.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for expanded polystyrene (EPS) beads and the adhesive, which are after installation used for the thermal insulation of buildings. The EPS beads and the adhesive are mixed and processed on site.
This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
This standard does not cover factory made insulation products in the form of prefabricated shapes or boards made of bonded EPS beads.
Products with a declared thermal resistance lower than 0,25 (m² x K)/W or a declared thermal conductivity at 10 °C greater than 0,1 W/(m x K) are not covered by this standard.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day