ISO/IEC 7816-2:1999/Amd 1:2004

Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimensions and location of the contacts — Amendment 1: Assignment of contacts C4 and C8

Cartes d'identification — Cartes à circuit intégré à contacts — Partie 2: Cartes à contact — Dimensions et emplacements des contacts — Amendement 1: Attribution des contacts C4 et C8

General Information

• Status: Withdrawn
• Publication Date: 10-Jun-2004
• Withdrawal Date: 10-Jun-2004
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17/WG 4 - Generic interfaces and protocols for security devices
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 11-Oct-2007

Relations

• Revised: ISO/IEC 7816-2:2007 - Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimensions and location of the contacts
• Effective Date: 15-Apr-2008
• Amends: ISO/IEC 7816-2:1999 - Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimensions and location of the contacts
• Effective Date: 06-Jun-2022
• Child: ISO/IEC 7816-2:1999 - Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimensions and location of the contacts
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 7816-2
First edition
1999-03-01
AMENDMENT 1
2004-06-01
Identification cards — Integrated circuit
cards —
Part 2:
Cards with contacts — Dimensions and
location of the contacts
AMENDMENT 1: Assignment of contacts C4
and C8
Cartes d'identification — Cartes à circuit intégré —
Partie 2: Cartes à contacts — Dimensions et emplacements des
contacts
AMENDEMENT 1: Attribution des contacts C4 et C8




Reference number
ISO/IEC 7816-2:1999/Amd.1:2004(E)
©
ISO/IEC 2004

---------------------- Page: 1 ----------------------
ISO/IEC 7816-2:1999/Amd.1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO/IEC 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2004 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 7816-2:1999/Amd.1:2004(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Amendment 1 to ISO/IEC 7816-2:1999 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information techn
...