ISO/IEC 10373-9:2011
(Main)Identification cards — Test methods — Part 9: Optical memory cards — Holographic recording method
Identification cards — Test methods — Part 9: Optical memory cards — Holographic recording method
ISO/IEC 10373-9:2011 defines test methods for characteristics of identification cards according to the definition given in ISO/IEC 7810. It is specific to optical memory cards that use the holographic recording method technology. Each test method is cross‑referenced to one or more base standards, i.e. ISO/IEC 7810 or one or more of the supplementary International Standards that define the information storage technologies employed in identification card applications.
Cartes d'identification — Méthodes d'essai — Partie 9: Cartes à mémoire optique — Méthode d'enregistrement holographique
General Information
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 10373-9
First edition
2011-08-01
Identification cards — Test methods —
Part 9:
Optical memory cards — Holographic
recording method
Cartes d'identification — Méthodes d'essai —
Partie 9: Cartes à mémoire optique — Méthode d'enregistrement
holographique
Reference number
ISO/IEC 10373-9:2011(E)
©
ISO/IEC 2011
---------------------- Page: 1 ----------------------
ISO/IEC 10373-9:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 10373-9:2011(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Default items applicable to the test methods.2
4.1 Test environment.2
4.2 Pre-conditioning .2
4.3 Selection of test methods.2
4.4 Default tolerance .2
4.5 Total measurement uncertainty .2
5 Test methods .3
5.1 Location of accessible optical area and reference track .3
5.1.1 Procedure.3
5.1.2 Test report.3
5.2 Skew.3
5.2.1 Apparatus for skew measurement.4
5.2.2 Procedure for skew measurement.4
5.2.3 Test report.5
5.3 Hologram size.5
5.3.1 Apparatus for hologram size measurement .5
5.3.2 Procedure for hologram size measurement .5
5.3.3 Test report.5
5.4 Arrangement of multiple holograms .5
5.4.1 Apparatus for measuring the arrangement of multiple holograms .6
5.4.2 Procedure for measuring the arrangement of multiple holograms .6
5.4.3 Test report.6
5.5 Optical properties of the media .6
5.5.1 Apparatus for measuring the optical properties of the media.7
5.5.2 Procedure for measuring the optical properties of the media.7
5.5.3 Test report.8
Bibliography.9
© ISO/IEC 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 10373-9:2011(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 10373-9 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identification.
ISO/IEC 10373 consists of the following parts, under the general title Identification cards — Test methods:
⎯ Part 1: General characteristics
⎯ Part 2: Cards with magnetic stripes
⎯ Part 3: Integrated circuit cards with contacts and related interface devices
⎯ Part 5: Optical memory cards
⎯ Part 6: Proximity cards
⎯ Part 7: Vicinity cards
⎯ Part 8: USB-ICC
⎯ Part 9: Optical memory cards — Holographic recording method
iv © ISO/IEC 2011 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 10373-9:2011(E)
Introduction
ISO/IEC 10373 defines test methods in support of ISO/IEC 11695, which specifies optical holographic
memory cards and the use of such cards for the storage and interchange of digital data.
The International Organization for Standardization (ISO) and International Electrotechnical Commission (IEC)
draw attention to the fact that it is claimed that compliance with this document may involve the use of patents.
ISO and the IEC take no position concerning the evidence, validity and scope of these patent rights.
The holders of these patent rights have assured ISO and the IEC that they are willing to negotiate licences
under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this
respect, the statements of the holders of these patent rights are registered with ISO and the IEC. Information
may be obtained from:
Certego GmbH
Lichtenbergstrasse 8
85748 Garching
Germany
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights other than those identified above. ISO and the IEC shall not be held responsible for identifying any or
all such patent rights.
© ISO/IEC 2011 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO/IEC 10373-9:2011(E)
Identification cards — Test methods —
Part 9:
Optical memory cards — Holographic recording method
1 Scope
This part of ISO/IEC 10373 defines test methods for characteristics of identification cards according to the
definition given in ISO/IEC 7810. It is specific to optical memory cards that use the holographic recording
method technology. Each test method is cross-referenced to one or more base standards, i.e. ISO/IEC 7810
or one or more of the supplementary International Standards that define the information storage technologies
employed in identification card applications.
NOTE 1 Criteria for acceptability do not form part of ISO/IEC 10373, but will be found in the International Standards
mentioned above.
NOTE 2 Test methods defined in this part of ISO/IEC 10373 are intended to be performed separately. A given card is
not required to pass through all the tests sequentially.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 11695-2, Identification cards — Optical memory cards — Holographic recording method — Part 2:
Dimensions and location of accessible optical area
ISO/IEC 11695-3, Identification cards — Optical memory cards — Holographic recording method — Part 3:
Optical properties and characteristics
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
test method
method for testing characteristics of identification cards for the purpose of confirming t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.