ISO/IEC 18013-3:2017
(Main)Information technology — Personal identification — ISO-compliant driving licence — Part 3: Access control, authentication and integrity validation
Information technology — Personal identification — ISO-compliant driving licence — Part 3: Access control, authentication and integrity validation
ISO/IEC 18013 establishes guidelines for the design format and data content of an ISO-compliant driving licence (IDL) with regard to human-readable features (ISO/IEC 18013‑1), machine-readable technologies (ISO/IEC 18013‑2), and access control, authentication and integrity validation (ISO/IEC 18013‑3). It creates a common basis for international use and mutual recognition of the IDL without impeding individual countries/states to apply their privacy rules and national/community/regional motor vehicle authorities in taking care of their specific needs. ISO 18013-3:2017 - is based on the machine-readable data content specified in ISO/IEC 18013‑2; - specifies mechanisms and rules available to issuing authorities (IAs) for: - access control (i.e. limiting access to the machine-readable data recorded on the IDL), - document authentication (i.e. confirming that the document was issued by the claimed IA), and - data integrity validation (i.e. confirming that the data has not been changed since issuing). ISO 1813-3:2017 does not address issues related to the subsequent use of data obtained from the IDL, e.g. privacy issues.
Technologies de l'information — Identification des personnes — Permis de conduire conforme à l'ISO — Partie 3: Contrôle d'accès, authentification et validation d'intégrité
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 18013-3
Second edition
2017-04
Information technology — Personal
identification — ISO-compliant driving
licence —
Part 3:
Access control, authentication and
integrity validation
Technologies de l’information — Identification des personnes —
Permis de conduire conforme à l’ISO —
Partie 3: Contrôle d’accès, authentification et validation d’intégrité
Reference number
ISO/IEC 18013-3:2017(E)
©
ISO/IEC 2017
---------------------- Page: 1 ----------------------
ISO/IEC 18013-3:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO/IEC 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 18013-3:2017(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Abbreviated terms . 6
5 Conformance . 8
6 Functional requirements . 8
6.1 Access control . 8
6.2 Document authentication . 8
6.3 Data integrity validation . 8
7 Mapping of mechanisms to requirements and technologies .11
8 Mechanisms .12
8.1 Passive authentication .12
8.1.1 Purpose .12
8.1.2 Applicability .12
8.1.3 Description . . .12
8.1.4 Hash function .13
8.1.5 Signing method .14
8.2 Active authentication .17
8.2.1 Purpose .17
8.2.2 Applicability .17
8.2.3 Description . . .17
8.2.4 Mechanism .17
8.3 Scanning area identifier .19
8.3.1 Applicability .19
8.3.2 Description . . .19
8.4 Non-match alert .30
8.4.1 Purpose .30
8.4.2 Applicability .30
8.4.3 Description . . .30
8.4.4 Mechanism .31
8.5 Basic access protection .32
8.5.1 Purpose .32
8.5.2 Applicability .32
8.5.3 Description . . .32
8.5.4 Mechanism .33
8.6 Extended Access Control v1 .34
8.6.1 Purpose .34
8.6.2 Applicability .34
8.6.3 Description and mechanism .34
8.7 PACE .35
8.7.1 Purpose .35
8.7.2 Applicability .35
8.7.3 Description and mechanism .35
8.7.4 PACE relative to BAP .35
9 Security mechanism indicator .36
10 SIC LDS .37
10.1 General .37
10.2 EF.SOD – Document security object (short EF identifier = ‘1D’, Tag = ‘77’) .39
© ISO/IEC 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 18013-3:2017(E)
10.3 EF.DG12 Non-match alert (short EF identifier= ‘0C’, Tag = ‘71’) .39
10.4 EF.DG13 Active authentication (short EF identifier = ‘0D’, Tag = ‘6F’) .39
10.5 EF.DG14 EACv1 (short EF identifier = ‘0E’, Tag = ‘6E’) .40
10.6 EF.CardAccess if PACE is supported (short EF identifier = ‘1C’) .40
Annex A (informative) Public key infrastructure (PKI) .41
Annex B (normative) Basic access protection .51
Annex C (normative) PACE .67
Annex D (normative) Extended Access Control v1 .72
Annex E (normative) SIC command set .76
Annex F (normative) List of tags used .78
Bibliography .80
iv © ISO/IEC 2017 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 18013-3:2017(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
The committee responsible for this document is ISO/IEC JTC 1, Information technology, SC 17, Cards and
personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 18013-3:2009), which has been
technically revised. It also incorporates the Amendments ISO/IEC 18013-3:2009/Amd 1:2012 and
ISO/IEC 18013-3:2009/Amd 2:2014, and the Technical Corrigenda ISO/IEC 18013-3:2009/Cor 1:2011
and ISO/IEC 18013-3:2009/Cor 2:2013.
The most significant changes are the following:
— In the interest of interoperability of cards used for personal identification, the authentication
protocols for the IDL are simplified. Active Authentication is harmonised with other ISO standards
and thus BAP configurations 2, 3 and 4, as well as EAP are no longer supported by this document.
— Replacing EAP, the optional EACv1 protocol is defined for the IDL, enabling access control to sensitive
biometric data stored on an integrated circuit. EACv1 may be used in conjunction with either BAP
configuration 1 or PACE.
— The optional PACE protocol enables access control to the data stored on an integrated circuit. The
PACE protocol is a password authenticated Diffie Hellman key agreement protocol based on a (short)
input string that provides secure communication between a secure integrated circuit on an IDL
and a terminal and allows various implementation options (mappings, input strings, algorithms).
The PACE protocol implementation for the IDL is restricted to Elliptic Curve Diffie Hellman (ECDH)
generic mapping and can be used as a stand-alone protocol or in combination with the EACv1
protocol.
A list of all the parts in the ISO/IEC 18013 series can be found on the ISO website.
© ISO/IEC 2017 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/IEC 18013-3:2017(E)
Introduction
This document prescribes requirements for the implementation of mechanisms to control access to
data recorded in the machine-readable technology on an ISO-compliant driving licence (IDL), verifying
the origin of an IDL, and confirming data integrity.
One of the functions of an IDL is to facilitate international interchange. While storing data in machine-
readable form on the IDL supports this function by speeding up data input and eliminating transcription
errors, certain machine-readable technologies are vulnerable to being read without the knowledge of
the card holder and to other means of unauthorized access by unintended persons that is other than
driving licence or law enforcement authorities. Controlling access to IDL data stored in machine-
readable form protects the data on the card from being read remotely by electronic means without the
knowledge of the card holder.
Identifying falsified driving licences or an alteration to the human-readable data on authentic driving
licences present a major problem for driving licence and law enforcement authorities, both domestically
and in the context of international interchange. Verifying the authenticity of an IDL and confirming
the integrity of the data recorded on an IDL provide driving licence and law enforcement authorities
with a means to identify an authentic IDL from a falsified or altered one in the interests of traffic law
enforcement and other traffic safety processes.
vi © ISO/IEC 2017 – All rights reserved
---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO/IEC 18013-3:2017(E)
Information technology — Personal identification — ISO-
compliant driving licence —
Part 3:
Access control, authentication and integrity validation
1 Scope
ISO/IEC 18013 establishes guidelines for the design format and data content of an ISO-compliant
driving licence (IDL) with regard to human-readable features (ISO/IEC 18013-1), machine-readable
technologies (ISO/IEC 18013-2), and access control, authentication and integrity validation
(ISO/IEC 18013-3). It creates a common basis for international use and mutual recognition of the IDL
without impeding individual countries/states to apply their privacy rules and national/community/
regional motor vehicle authorities in taking care of their specific needs.
This document
— is based on the machine-readable data content specified in ISO/IEC 18013-2;
— specifies mechanisms and rules available to issuing authorities (IAs) for:
— access control (i.e. limiting access to the machine-readable data recorded on the IDL),
— document authentication (i.e. confirming that the document was issued by the claimed IA), and
— data integrity validation (i.e. confirming that the data has not been changed since issuing).
This document does not address issues related to the subsequent use of data obtained from the IDL, e.g.
privacy issues.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1831:1980, Printing specifications for optical character recognition
ISO/IEC 7816-4:2013, Identification cards — Integrated circuit cards — Part 4: Organization, security and
commands for interchange
ISO/IEC 8859-1:1998, Information technology — 8-bit single-byte coded graphic character sets — Part 1:
Latin alphabet No. 1
ISO 9796-2, Information technology — Security techniques — Digital signature schemes giving message
recovery — Part 2: Integer factorization based mechanisms
1)
ISO/IEC 9797-1:1999 , Information technology — Security techniques — Message Authentication Codes
(MACs) — Part 1: Mechanisms using a block cipher
ISO/IEC 10118-3:2004, Information technology — Security techniques — Hash-functions — Part 3:
Dedicated hash-functions
1) ISO/IEC 9797-1:1999 is withdrawn and replaced by the 2011 version.
© ISO/IEC 2017 – All rights reserved 1
---------------------- Page: 7 ----------------------
ISO/IEC 18013-3:2017(E)
2)
ISO/IEC 11770-2:1996 , Information technology — Security techniques — Key management — Part 2:
Mechanisms using symmetric techniques
ISO/IEC 11770-2:1996/Cor.1:2005, Information technology — Security techniques — Key management —
Part 2: Mechanisms using symmetric techniques — Technical Corrigendum 1
ISO/IEC 18013-1, Information technology — Personal identification — ISO-compliant driving licence —
Part 1: Physical characteristics and basic data set
ISO/IEC 18013-2, Information technology — Personal identification — ISO-compliant driving licence —
Part 2: Machine-readable technologies
3)
ISO/IEC 18033-3:2005 , Information technology — Security techniques — Encryption algorithms —
Part 3: Block ciphers
I S O/ I EC 18 033-3:20 05/C or1: 20 06 , Information technology — Security techniques — Encryption
algorithms — Part 3: Block ciphers — Technical Corrigendum 1
I S O/ I EC 18 033-3:20 05/C or2: 20 07, Information technology — Security techniques — Encryption
algorithms — Part 3: Block ciphers — Technical Corrigendum 2
ANSI X9.62:2005, Public Key Cryptography for the Financial Services Industry: The Elliptic Curve Digital
Signature Algorithm (ECDSA)
BSI Technical Guideline TR-03110-1: Advanced Security Mechanisms for Machine Readable Travel
Documents — Part 1 — eMRTDs with BAC/PACEv2 and EACv1 — Version 2.10 — 2012-03-20
BSI Technical Guideline TR-03110-3: Advanced Security Mechanisms for Machine Readable Travel
Documents — Part 3 — Common Specifications — Version 2.10 — 2012-03-20
FIPS 186-2 (including Change Notice), Digital Signature Standard (DSS), Federal Information Processing
Standards Publication, National Institute of Standards and Technology, 27 January 2000
ICAO Technical Report – Supplemental Access Control for Machine Readable Travel Documents, v1.01, 2010
[TR-PACE]
NIST/SP 800-38B, Recommendation for Block Cipher Modes of Operation: The CMAC Mode for
Authentication, May 2005
4)
RFC 2631, E. Rescorla, Diffie-Hellman Key Agreement Method, June 1999
RFC 3279, W. Polk et al., Algorithms and Identifiers for the Internet X.509 Public Key Infrastructure
4
Certificate and Certificate Revocation List (CRL) Profile, April 2002
RFC 3280, R. Housley et al., Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation
1
List (CRL) Profile, April 2002
1
RFC 3369, R. Housley, Cryptographic Message Syntax, August 2002
RFC 4055, J. Schaad, B. Kaliski, R. Housley, Additional Algorithms and Identifiers for RSA Cryptography for
use in the Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation List (CRL) Profile,
1
June 2005
RFC 5639, M. Lochter, J. Merkle, Elliptic Curve Cryptography (ECC) Brainpool Standard Curves and Curve
1
Generation, March 2010
2) ISO/IEC 11770-2:1996 is withdrawn and replaced by the 2008 version.
3) ISO/IEC 18033-3:2005 is withdrawn and replaced by the 2010 version.
4) http:// www .ietf .org/ rfc .html
2 © ISO/IEC 2017 – All rights reserved
---------------------- Page: 8 ----------------------
ISO/IEC 18013-3:2017(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC 18013-1, ISO/IEC 18013-
2 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
active authentication
mechanism that uses information stored in a secure area of a secure integrated circuit (SIC) (3.17) to
confirm that the SIC and the other machine-readable data were issued together
Note 1 to entry: See 8.2.
3.2
basic access protection
BAP
mechanism to confirm that an inspection system (IS) has physical access to a proximity integrated
circuit card (PICC) before the IS is allowed access to the data stored on the PICC and to ensure that
communication between the IS and the PICC (once access is authorized) is protected
Note 1 to entry: See 8.5 and Annex B.
3.3
chip authentication
ephemeral-static key agreement protocol that provides authentication of the secure integrated circuit
(3.17) and strong secure messaging
Note 1 to entry: See 8.6.
3.4
clone
unauthorized exact copy of a document that has the same security characteristics as the original
document and that cannot be distinguished from the legitimate one
3.5
eavesdropping
unauthorized interception and interpretation of information-bearing emanations
[SOURCE: ISO/IEC 2382-8:2015, 08.05.25, modified]
3.6
extended access control v1
EACv1
protocol used to limit access to optional signature and biometric data groups
Note 1 to entry: See 8.6 and Annex D.
3.7
input string
string of characters printed on an ISO-compliant driving licence [as human-readable text, optionally (or
by specification) accompanied by or consisting of a machine-readable rendering thereof] used as input
(either manually or automatically through the use of suitable equipment) for the non-match alert and
BAP (3.2) or PACE (3.10) mechanisms
© ISO/IEC 2017 – All rights reserved 3
---------------------- Page: 9 ----------------------
ISO/IEC 18013-3:2017(E)
3.8
issuing authority
IA
licensing authority (or issuing country if separate licensing authorities have not been authorized) which
applies a digital signature to an ISO-compliant driving licence and is responsible for the associated key
management
[SOURCE: ISO/IEC 18013-1]
3.9
non-match alert
mechanism to detect any differences between the machine-readable information and (some of) the
human-readable information on an ISO-compliant driving licence
Note 1 to entry: See 8.4.
3.10
PACE
alternative mechanism to BAP to confirm that an inspection system (IS) has physical access to a secure
integrated circuit (SIC) (3.17) on a driving licence card before the IS is allowed to access to the data
stored on the SIC and to establish a secure communication channel between the IS and SIC once access
is authorised
Note 1 to entry: As stated in TR-PACE, PACE refers to PACE v2.
Note 2 to entry: See 8.7 and Annex C.
3.11
passive authentication
mechanism to confirm that machine-readable data on an ISO-compliant driving licence (IDL) has not
been changed since the IDL was issued
Note 1 to entry: See 8.1.
3.12
pseudo issuing authority
PIA
authority that does not issue ISO-compliant driving licences [but that is similar to an issuing
authority (IA) (3.8) in all other respects] and which does not issue document keys, but which does have
a root key pair with which it can sign documents of other IAs or PIAs that it trusts
3.13
public key infrastructure
PKI
technologies and products using public key (asymmetric) cryptography
Note 1 to entry: Both passive authentication (3.11) and extended access protection use this technology.
3.14
reading authority
RA
authorized entity reading the machine-readable data on an ISO-compliant driving licence (IDL)
Note 1 to entry: Driving licence authorities other than the authority that issued the IDL and law enforcement
authorities are examples of reading authorities.
3.15
reference string
string of characters used as a reference against which to compare the input string (3.7) when using the
non-match alert (3.9) mechanism, and used for session key calculation purposes by the secure integrated
circuit (3.17) during execution of the basic access protection (3.2) mechanism
4 © ISO/IEC 2017 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/IEC 18013-3:2017(E)
3.16
scanning area identifier
SAI
one or more graphical elements that demarcate an input string (3.7)
3.17
secure integrated circuit
SIC
integrated circuit that includes both a security feature (or security features), and memory and/or a
central processing unit
Note 1 to entry: An integrated circuit card with contacts and a proximity integrated circuit card (PICC) are
examples of a SIC.
Note 2 to entry: A SIC can be embedded in different solutions, for example in ID-1 sized cards (as used for the ISO-
compliant driving licence) and in a booklet (as found in passports).
3.18
secure memory
integrated circuit (IC) memory of which the content [once populated by an issuing authority (3.8) during
the personalization process] is accessible only by the IC operating system for internal use, and cannot
be made available by the operating system to any reading device
3.19
skimming
reading data from a proximity integrated circuit card (PICC) without the card holder’s awareness
3.20
trust chain
sequential set of trust points (3.23) that a verifying authority (3.26) references to verify a specific issuing
authority’s (3.8) public root key
3.21
trust model
description of the functional and logical aspects of a traditional public key infrastructure (3.13)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.