ISO 16162:2010
(Main)Continuously cold-rolled steel sheet products — Dimensional and shape tolerances
Continuously cold-rolled steel sheet products — Dimensional and shape tolerances
ISO 16162:2010 applies to dimensional and shape tolerances for all continuously cold-rolled steel sheet products.
Tôles en acier laminées à froid en continu — Tolérances sur dimensions et forme
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 16162
Third edition
2010-11-15
Continuously cold-rolled steel sheet
products — Dimensional and shape
tolerances
Tôles en acier laminées à froid en continu — Tolérances
sur dimensions et forme
Reference number
ISO 16162:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 16162:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 16162:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16162 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 12, Continuous mill
flat rolled products.
This third edition cancels and replaces the second edition (ISO 16162:2005), which has been technically
revised.
© ISO 2010 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 16162:2010(E)
Continuously cold-rolled steel sheet products — Dimensional
and shape tolerances
1 Scope
This International Standard applies to dimensional and shape tolerances for all continuously cold-rolled steel
sheet products.
Note Cold-rolled steel strip is not covered by this International Standard.
2 Dimensional tolerances
Dimensional tolerances are given in Tables 1 to 9.
Table 1 — Normal thickness tolerances for coils and cut lengths
Dimensions and tolerances in millimetres
a,b,c
Thickness tolerances for specified thicknesses
Specified
width
u0,4 > 0,4 u0,6 > 0,6 u0,8 > 0,8 u1,0 > 1,0 u1,2 > 1,2 u1,6 > 1,6 u2,0 > 2,0 u2,5 > 2,5 u3,0 > 3,0 u4,0
600 u1 200 ±0,04 ±0,05 ±0,07 ±0,08 ±0,09 ±0,11 ±0,13 ±0,15 ±0,18 ±0,20
> 1 200 u1 500 ±0,05 ±0,06 ±0,08 ±0,09 ±0,10 ±0,12 ±0,14 ±0,16 ±0,19 ±0,21
> 1 500 u1 800 — ±0,08 ±0,09 ±0,10 ±0,12 ±0,14 ±0,16 ±0,18 ±0,21 ±0,23
When International Standards that reference this standard permit sheet that is slit to less than 600 mm in width to be considered as
sheet, tolerances shall be subject to agreement.
a
The thickness tolerances for sheet in coil form are the same as for sheet supplied in cut lengths but, in cases where welds are
present, the tolerances shall be double those given over a length of 15 m in the vicinity of the weld.
b
For specified strength levels of R = 360 MPa and greater, increase the thickness tolerances by 10 %, applying normal rounding-off
e
procedures.
c
Thickness is measured at any point on the sheet not less than 25 mm from a side edge.
© ISO 2010 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 16162:2010(E)
Table 2 — Restricted thickness tolerances for coils and cut lengths
Dimensions and tolerances in millimetres
a,b,c
Thickness tolerances for specified thicknesses
Specified
width
u0,4 > 0,4 u0,6 > 0,6 u0,8 > 0,8 u1,0 > 1,0 u1,2 > 1,2 u1,6 > 1,6 u2,0 > 2,0 u2,5 > 2,5 u3,0 >
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.