ISO/TS 21219-14:2016
(Main)Intelligent transport systems — Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2) — Part 14: Parking information application (TPEG2-PKI)
Intelligent transport systems — Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2) — Part 14: Parking information application (TPEG2-PKI)
ISO/TS 21219-14:2016 specifies the TPEG Parking Information application which has been designed to deliver parking information to a variety of receivers using a number of different channels, foremost of course are digital broadcasting and Internet technologies. Parking information may be presented to the user in many different ways, including text, voice, or graphics. Today, traffic congestion has become a serious problem in urban areas. Some traffic congestion is attributed to drivers searching for parking spaces. Therefore, timely provision of parking information could help ease traffic congestion. Furthermore, parking information would be valuable for the visitor, particularly when it could be used to signal where a temporary parking facility is established for a special occasion.
Systèmes intelligents de transport — Informations sur le trafic et le tourisme via le groupe expert du protocole de transport, génération 2 (TPEG2) — Partie 14: Informations relatives aux parcs de stationnement (TPEG-PKI)
General Information
Relations
Buy Standard
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 21219-14
First edition
2016-06-01
Intelligent transport systems —
Traffic and travel information (TTI)
via transport protocol experts group,
generation 2 (TPEG2) —
Part 14:
Parking information application
(TPEG2-PKI)
Systèmes intelligents de transport — Informations sur le trafic et le
tourisme via le groupe expert du protocole de transport, génération 2
(TPEG2) —
Partie 14: Informations relatives aux parcs de stationnement
(TPEG-PKI)
Reference number
ISO/TS 21219-14:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO/TS 21219-14:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 21219-14:2016(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 2
5 Application specific constraints . 2
5.1 Application identification . 2
5.2 Version number signalling . 3
5.3 Ordered components . 3
5.4 Extensions . 3
5.5 TPEG Service Component Frame. 3
6 PKI Message components . 3
6.1 ParkingMessage . 3
6.2 MMCSwitch . 5
6.3 MessageManagementContainerLink. 5
6.4 MMCMasterLink . 5
6.5 MMCPartLink . 5
6.6 ParkingLocation . 5
6.7 ParkingSiteDescription . 5
6.8 ParkingInfo . 6
6.9 Logo . 7
6.10 Contact . 7
6.11 ParkingSpecification . 7
6.12 InformationFor . 8
6.13 SizeRestrictions . 9
6.14 GateInfo . 9
6.15 ParkingForEvent .10
6.16 ToSite .10
6.17 OpeningHours .10
6.18 PricingPayment .11
6.19 PaymentDetails .11
6.20 Facilities .11
6.21 AssociatedService .12
6.22 CurrentCapacity .12
6.23 CurrentCapacityFor .13
6.24 ExpectedCapacity .13
6.25 ExpectedCapacityFor .14
6.26 Advice .14
7 PKI Tables .14
7.1 pki001:VehicleType .14
7.2 pki002:ParkingType .15
7.3 pki003:UserType .16
7.4 pki004:FuelType .16
7.5 pki005:AvailableFeatures .17
7.6 pki006:EventType .17
7.7 pki007: Reservability .18
7.8 pki008:FacilityType .18
7.9 pki009:SupervisionType .18
7.10 pki010:SecurityType .19
7.11 pki011:AssociatedService .19
7.12 pki012:ParkingStatus .20
© ISO 2016 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 21219-14:2016(E)
7.13 pki013:PaymentMethod .20
7.14 pki014:SiteServed .21
7.15 pki015:GateType .21
7.16 pki016:ContactType .21
7.17 pki017:TransportType .22
7.18 pki018:OpeningHoursType .22
7.19 pki019:TermType .22
7.20 pki020:Advice .23
7.21 pki021:Tendency .23
7.22 pki022:FeeType .23
Annex A (normative) TPEG PKI, TPEG-Binary Representation .25
Annex B (normative) TPEG PKI, tpegML Representation .37
Bibliography .50
iv © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/TS 21219-14:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 204, Intelligent transport systems.
ISO/TS 21219 consists of the following parts, under the general title Intelligent transport systems —
Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2):
— Part 1: Introduction, numbering and versions (TPEG2-INV)
— Part 2: UML modelling rules
— Part 3: UML to binary conversion rules
— Part 4: UML to XML conversion rules
— Part 5: Service framework (TPEG2-SFW)
— Part 6: Message management container (TPEG2-MMC)
— Part 9: Service and network information (TPEG2-SNI)
— Part 10: Conditional access information (TPEG2-CAI)
— Part 14: Parking information (TPEG2-PKI)
— Part 15: Traffic event compact (TPEG2-TEC)
— Part 18: Traffic flow and prediction application (TPEG2-TFP)
— Part 19: Weather information (TPEG2-WEA)
The following parts are under preparation:
— Part 16: Fuel price information and availability application (TPEG2-FPI)
— Part 23: Roads and multi-modal routes application (TPEG2-RMR)
— Part 24: Light encryption (TPEG2-LTE)
© ISO 2016 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/TS 21219-14:2016(E)
— Part 25: Electromobility charging infrastructure (TPEG2-EMI)
The following parts are planned:
— Part 7: Location referencing container
— Part 21: Geographic location referencing
— Part 22: OpenLR location referencing
vi © ISO 2016 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/TS 21219-14:2016(E)
Introduction
History
TPEG technology was originally proposed by the European Broadcasting Union (EBU) Broadcast
Management Committee, who established the B/TPEG project group in the autumn of 1997 with a brief
to develop, as soon as possible, a new protocol for broadcasting traffic and travel-related information
in the multimedia environment. TPEG technology, its applications and service features were designed
to enable travel-related messages to be coded, decoded, filtered and understood by humans (visually
and/or audibly in the user’s language) and by agent systems. Originally, a byte-oriented data stream
format, which may be carried on almost any digital bearer with an appropriate adaptation layer,
was developed. Hierarchically structured TPEG messages from service providers to end-users were
designed to transfer information from the service provider database to an end-user’s equipment.
One year later in December 1998, the B/TPEG group produced its first EBU specifications. Two
documents were released. Part 2 (TPEG-SSF, which became ISO/TS 18234-2) described the Syntax,
Semantics and Framing structure, which was used for all TPEG applications. Meanwhile, Part 4 (TPEG-
RTM, which became ISO/TS 18234-4) described the first application for Road Traffic Messages.
Subsequently in March 1999, CEN TC 278, in conjunction with ISO/TC 204, established a group
comprising members of the former EBU B/TPEG and this committee continued development work.
Further parts were developed to make the initial set of four parts, enabling the implementation of a
consistent service. Part 3 (TPEG-SNI, ISO/TS 18234-3) described the Service and Network Information
Application, used by all service implementations to ensure appropriate referencing from one service
source to another.
Part 1 (TPEG-INV, ISO/TS 18234-1) completed the series by describing the other parts and their
relationship; it also contained the application IDs used within the other parts. Additionally, Part 5,
Public Transport Information Application (TPEG-PTI, ISO/TS 18234-5), was developed. The so-called
TPEG-LOC location referencing method, which enabled both map-based TPEG-decoders and non-map-
based ones to deliver either map-based location referencing or human readable text information, was
issued as ISO/TS 18234-6 to be used in association with the other applications parts of the ISO/TS 18234
series to provide location referencing.
The ISO/TS 18234 series has become known as TPEG Generation 1.
TPEG Generation 2
When the Traveller Information Services Association (TISA), derived from former forums, was
inaugurated in December 2007, TPEG development was taken over by TISA and continued in the TPEG
Applications Working Group.
It was about this time that the (then) new Unified Modelling Language (UML) was seen as having major
advantages for the development of new TPEG Applications in communities who would not necessarily
have binary physical format skills required to extend the original TPEG TS work. It was also realized
that the XML format for TPEG described within the ISO/TS 24530 series (now superseded) had a greater
significance than previously foreseen, especially in the content-generation segment and that keeping
two physical formats in synchronism, in different standards series, would be rather difficult.
As a result, TISA set about the development of a new TPEG structure that would be UML-based. This has
subsequently become known as TPEG Generation 2.
TPEG2 is embodied in the ISO/TS 21219 series and it comprises many parts that cover introduction,
rules, toolkit and application components. TPEG2 is built around UML modelling and has a core of rules
that contain the modelling strategy covered in ISO/TS 21219-2, ISO/TS 21219-3, ISO/TS 21219-4 and
the conversion to two current physical formats: binary and XML; others could be added in the future.
TISA uses an automated tool to convert from the agreed UML model XMI file directly into an MS Word
document file, to minimize drafting errors, that forms the Annex for each physical format.
© ISO 2016 – All rights reserved vii
---------------------- Page: 7 ----------------------
ISO/TS 21219-14:2016(E)
TPEG2 has a three container conceptual structure: Message Management (ISO/TS 21219-6), Application
(many Parts) and Location Referencing (ISO/TS 21219-7). This structure has flexible capability and can
accommodate many differing use cases that have been proposed within the TTI sector and wider for
hierarchical message content.
TPEG2 also has many location referencing options as required by the service provider community, any
of which may be delivered by vectoring data included in the Location Referencing Container.
The following classification provides a helpful grouping of the different TPEG2 parts according to their
intended purpose:
— Toolkit parts: TPEG2-INV (ISO/TS 21219-1), TPEG2-UML (ISO/TS 21219-2), TPEG2-UBCR
(ISO/TS 21219-3), TPEG2-UXCR (ISO/TS 21219-4), TPEG2-SFW (ISO/TS 21219-5), TPEG2-MMC
(ISO/TS 21219-6), TPEG2-LRC (ISO/TS 21219-7), TPEG2-LTE (ISO/TS 21219-24);
— Special applications: TPEG2-SNI (ISO/TS 21219-9), TPEG2-CAI (ISO/TS 21219-10);
— Location referencing: TPEG2-ULR (ISO/TS 21219-11), TPEG2-GLR (ISO/TS 21219-21), TPEG2-OLR
(ISO/TS 21219-22);
— Applications: Applications: TPEG2-PKI (ISO/TS 21219-14), TPEG2-TEC (ISO/TS 21219-15), TPEG2-
FPI (ISO/TS 21219-16), TPEG2-TFP (ISO/TS 21219-18), TPEG2-WEA (ISO/TS 21219-19), TPEG2-
RMR (ISO/TS 21219-23), TPEG2-EMI (ISO/TS 21219-25).
TPEG2 has been developed to be broadly (but not entirely) backward compatible with TPEG1 to assist
in transitions from earlier implementations, while not hindering the TPEG2 innovative approach and
being able to support many new features, such as dealing with applications having both long-term,
unchanging content and highly dynamic content, such as Parking Information.
This Technical Specification is based on the TISA specification technical/editorial version reference:
SP13009/1.1/001.
viii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
TECHNICAL SPECIFICATION ISO/TS 21219-14:2016(E)
Intelligent transport systems — Traffic and travel
information (TTI) via transport protocol experts group,
generation 2 (TPEG2) —
Part 14:
Parking information application (TPEG2-PKI)
1 Scope
This part of ISO/TS 21219 specifies the TPEG Parking Information application which has been designed
to deliver parking information to a variety of receivers using a number of different channels, foremost
of course are digital broadcasting and Internet technologies. Parking information may be presented to
the user in many different ways, including text, voice, or graphics.
Today, traffic congestion has become a serious problem in urban areas. Some traffic congestion is
attributed to drivers searching for parking spaces. Therefore, timely provision of parking information
could help ease traffic congestion. Furthermore, parking information would be valuable for the visitor,
particularly when it could be used to signal where a temporary parking facility is established for a
special occasion.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO/TS 21219-1, Intelligent transport systems — Traffic and travel information via transport protocol
experts group, generation 2 (TPEG2) — Part 1: Introduction, numbering and versions (TPEG2-INV)
ISO/TS 21219-3, Intelligent transport systems — Traffic and travel information (TTI) via transport
protocol experts group, generation 2 (TPEG2) — Part 3: UML to binary conversion rules
ISO/TS 21219-4, Intelligent transport systems — Traffic and travel information (TTI) via transport
protocol experts group, generation 2 (TPEG2) — Part 4: UML to XML conversion rules
ISO/TS 21219-6, Intelligent transport systems — Traffic and travel information via transport protocol
experts group, generation 2 (TPEG2) — Part 6: Message management container (TPEG2-MMC)
3 Terms and definitions
3.1
Message Management Container
concept applied to the grouping of all message elements including Message Management Information of
a TPEG-Message together in one place
Note 1 to entry: See TPEG2 MMC documents (ISO/TS 21219-6) for full details of the Message Management
Container explanations.
© ISO 2016 – All rights reserved 1
---------------------- Page: 9 ----------------------
ISO/TS 21219-14:2016(E)
3.2
Location Referencing
means to provide information that allows a system to accurately identify a location
Note 1 to entry: The content of a location reference allows the location to be presented in a graphical or textual
manner to the end-user (e.g. coloured network graphs), as well as to be used for navigational systems purposes.
3.3
Location Referencing Container
concept applied to the grouping of all the Location Referencing elements, of a TPEG-Message, together
in one place
Note 1 to entry: See TPEG2 LRC documents (ISO/TS 21219-7) for full details of the Location Referencing container
explanations.
4 Abbreviated terms
ACID Application and Content Identifier
AID Application Identification
CA Conditional Access
CAI Conditional Access Information
CEN Comité Européen de Normalization
CRC Cyclic redundancy check
EBU European Broadcasting Union
ECM Entitlement Control Message
EMM Entitlement Management Message
MMC Message Management Container
n/a not available
SFW TPEG Service Framework: Modelling and Conversion Rules
TISA Traveller Information Services Association
5 Application specific constraints
5.1 Application identification
The word “application” is used in this part of ISO/TS 21219 to describe specific subsets of the TPEG
structure. An application defines a limited vocabulary for a certain type of messages, for example,
parking information or road traffic information. Each TPEG application is assigned a unique number,
called the Application Identification (AID). An AID is defined whenever a new application is developed
and these are all listed in ISO/TS 21219-1.
The application identification number is used within the TPEG-SNI application ISO/TS 21219-9 to
indicate how to process TPEG content and facilitates the routing of information to the appropriate
application decoder.
2 © ISO 2016 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/TS 21219-14:2016(E)
5.2 Version number signalling
Version numbering is used to track the separate versions of an application through its development and
deployment. The differences between these versions can have an impact on client devices.
The version numbering principle is defined in ISO/TS 21219-1.
Table 1 shows the current version numbers for signalling PKI within the SNI application.
Table 1 — Current version numbers for signalling of PKI
major version number 1
minor version number 1
5.3 Ordered components
TPEG-PKI does not generally require a fixed order of TPEG components, except where explicitly
modelled. The order for the PKI message components is shown in Figure 1; the first component shall
be the Message Management Container. This shall be the only component if the message is a cancellation
message. Otherwise, the MMC component shall be followed by the one or more Application Data
Container component(s) which includes the application-specific information.
Figure 1 — Composition of TPEG messages
5.4 Extensions
Future application extensions may insert new components or may replace existing components by new
ones without losing backward compatibility. That means that a PKI decoder shall be able to detect and
skip unknown components.
5.5 TPEG Service Compon
...
TECHNICAL ISO/TS
SPECIFICATION 21219-14
First edition
Intelligent transport systems —
Traffic and travel information (TTI)
via transport protocol experts group,
generation 2 (TPEG2) —
Part 14:
Parking information application
(TPEG2-PKI)
Systèmes intelligents de transport — Informations sur le trafic et le
tourisme via le groupe expert du protocole de transport, génération 2
(TPEG2) —
Partie 14: Informations relatives aux parcs de stationnement
(TPEG-PKI)
PROOF/ÉPREUVE
Reference number
ISO/TS 21219-14:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO/TS 21219-14:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 21219-14:2016(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 2
5 Application specific constraints . 2
5.1 Application identification . 2
5.2 Version number signalling . 3
5.3 Ordered components . 3
5.4 Extensions . 3
5.5 TPEG Service Component Frame. 3
6 PKI Message components . 3
6.1 ParkingMessage . 3
6.2 MMCSwitch . 5
6.3 MessageManagementContainerLink. 5
6.4 MMCMasterLink . 5
6.5 MMCPartLink . 5
6.6 ParkingLocation . 5
6.7 ParkingSiteDescription . 5
6.8 ParkingInfo . 6
6.9 Logo . 7
6.10 Contact . 7
6.11 ParkingSpecification . 7
6.12 InformationFor . 8
6.13 SizeRestrictions . 9
6.14 GateInfo . 9
6.15 ParkingForEvent .10
6.16 ToSite .10
6.17 OpeningHours .10
6.18 PricingPayment .11
6.19 PaymentDetails .11
6.20 Facilities .11
6.21 AssociatedService .12
6.22 CurrentCapacity .12
6.23 CurrentCapacityFor .13
6.24 ExpectedCapacity .13
6.25 ExpectedCapacityFor .14
6.26 Advice .14
7 PKI Tables .14
7.1 pki001:VehicleType .14
7.2 pki002:ParkingType .15
7.3 pki003:UserType .16
7.4 pki004:FuelType .16
7.5 pki005:AvailableFeatures .17
7.6 pki006:EventType .17
7.7 pki007: Reservability .18
7.8 pki008:FacilityType .18
7.9 pki009:SupervisionType .18
7.10 pki010:SecurityType .19
7.11 pki011:AssociatedService .19
7.12 pki012:ParkingStatus .20
© ISO 2016 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO/TS 21219-14:2016(E)
7.13 pki013:PaymentMethod .20
7.14 pki014:SiteServed .21
7.15 pki015:GateType .21
7.16 pki016:ContactType .21
7.17 pki017:TransportType .22
7.18 pki018:OpeningHoursType .22
7.19 pki019:TermType .22
7.20 pki020:Advice .23
7.21 pki021:Tendency .23
7.22 pki022:FeeType .23
Annex A (normative) TPEG PKI, TPEG-Binary Representation .25
Annex B (normative) TPEG PKI, tpegML Representation .37
Bibliography .50
iv PROOF/ÉPREUVE © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/TS 21219-14:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 204, Intelligent transport systems.
ISO/TS 21219 consists of the following parts, under the general title Intelligent transport systems —
Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2):
— Part 1: Introduction, numbering and versions (TPEG2-INV)
— Part 2: UML modelling rules
— Part 3: UML to binary conversion rules
— Part 4: UML to XML conversion rules
— Part 5: Service framework (TPEG2-SFW)
— Part 6: Message management container (TPEG2-MMC)
— Part 9: Service and network information (TPEG2-SNI)
— Part 10: Conditional access information (TPEG2-CAI)
— Part 14: Parking information (TPEG2-PKI)
— Part 15: Traffic event compact (TPEG2-TEC)
— Part 18: Traffic flow and prediction application (TPEG2-TFP)
— Part 19: Weather information (TPEG2-WEA)
The following parts are under preparation:
— Part 16: Fuel price information and availability application (TPEG2-FPI)
— Part 23: Roads and multi-modal routes application (TPEG2-RMR)
— Part 24: Light encryption (TPEG2-LTE)
© ISO 2016 – All rights reserved PROOF/ÉPREUVE v
---------------------- Page: 5 ----------------------
ISO/TS 21219-14:2016(E)
— Part 25: Electromobility information (TPEG2-EMI)
The following parts are planned:
— Part 7: Location referencing container
— Part 20 Extended TMC location referencing
— Part 21: Geographic location referencing
— Part 22: OpenLR location referencing
vi PROOF/ÉPREUVE © ISO 2016 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/TS 21219-14:2016(E)
Introduction
History
TPEG technology was originally proposed by the European Broadcasting Union (EBU) Broadcast
Management Committee, who established the B/TPEG project group in the autumn of 1997 with a brief
to develop, as soon as possible, a new protocol for broadcasting traffic and travel-related information
in the multimedia environment. TPEG technology, its applications and service features were designed
to enable travel-related messages to be coded, decoded, filtered and understood by humans (visually
and/or audibly in the user’s language) and by agent systems. Originally, a byte-oriented data stream
format, which may be carried on almost any digital bearer with an appropriate adaptation layer,
was developed. Hierarchically structured TPEG messages from service providers to end-users were
designed to transfer information from the service provider database to an end-user’s equipment.
One year later in December 1998, the B/TPEG group produced its first EBU specifications. Two
documents were released. Part 2 (TPEG-SSF, which became ISO/TS 18234-2) described the Syntax,
Semantics and Framing structure, which was used for all TPEG applications. Meanwhile, Part 4 (TPEG-
RTM, which became ISO/TS 18234-4) described the first application for Road Traffic Messages.
Subsequently in March 1999, CEN TC 278, in conjunction with ISO/TC 204, established a group
comprising members of the former EBU B/TPEG and this committee continued development work.
Further parts were developed to make the initial set of four parts, enabling the implementation of a
consistent service. Part 3 (TPEG-SNI, ISO/TS 18234-3) described the Service and Network Information
Application, used by all service implementations to ensure appropriate referencing from one service
source to another.
Part 1 (TPEG-INV, ISO/TS 18234-1) completed the series by describing the other parts and their
relationship; it also contained the application IDs used within the other parts. Additionally, Part 5,
Public Transport Information Application (TPEG-PTI, ISO/TS 18234-5), was developed. The so-called
TPEG-LOC location referencing method, which enabled both map-based TPEG-decoders and non-map-
based ones to deliver either map-based location referencing or human readable text information, was
issued as ISO/TS 18234-6 to be used in association with the other applications parts of the ISO/TS 18234
series to provide location referencing.
The ISO/TS 18234 series has become known as TPEG Generation 1.
TPEG Generation 2
When the Traveller Information Services Association (TISA), derived from former forums, was
inaugurated in December 2007, TPEG development was taken over by TISA and continued in the TPEG
Applications Working Group.
It was about this time that the (then) new Unified Modelling Language (UML) was seen as having major
advantages for the development of new TPEG Applications in communities who would not necessarily
have binary physical format skills required to extend the original TPEG TS work. It was also realized
that the XML format for TPEG described within the ISO/TS 24530 series (now superseded) had a greater
significance than previously foreseen, especially in the content-generation segment and that keeping
two physical formats in synchronism, in different standards series, would be rather difficult.
As a result, TISA set about the development of a new TPEG structure that would be UML-based. This has
subsequently become known as TPEG Generation 2.
TPEG2 is embodied in the ISO/TS 21219 series and it comprises many parts that cover introduction,
rules, toolkit and application components. TPEG2 is built around UML modelling and has a core of rules
that contain the modelling strategy covered in ISO/TS 21219-2, ISO/TS 21219-3, ISO/TS 21219-4 and
the conversion to two current physical formats: binary and XML; others could be added in the future.
TISA uses an automated tool to convert from the agreed UML model XMI file directly into an MS Word
document file, to minimize drafting errors, that forms the Annex for each physical format.
© ISO 2016 – All rights reserved PROOF/ÉPREUVE vii
---------------------- Page: 7 ----------------------
ISO/TS 21219-14:2016(E)
TPEG2 has a three container conceptual structure: Message Management (ISO/TS 21219-6), Application
(many Parts) and Location Referencing (ISO/TS 21219-7). This structure has flexible capability and can
accommodate many differing use cases that have been proposed within the TTI sector and wider for
hierarchical message content.
TPEG2 also has many location referencing options as required by the service provider community, any
of which may be delivered by vectoring data included in the Location Referencing Container.
The following classification provides a helpful grouping of the different TPEG2 parts according to their
intended purpose:
— Toolkit parts: TPEG2-INV (ISO/TS 21219-1), TPEG2-UML (ISO/TS 21219-2), TPEG2-UBCR
(ISO/TS 21219-3), TPEG2-UXCR (ISO/TS 21219-4), TPEG2-SFW (ISO/TS 21219-5), TPEG2-MMC
(ISO/TS 21219-6), TPEG2-LRC (ISO/TS 21219-7), TPEG2-LTE (ISO/TS 21219-24);
— Special applications: TPEG2-SNI (ISO/TS 21219-9), TPEG2-CAI (ISO/TS 21219-10);
— Location referencing: TPEG2-ULR (ISO/TS 21219-11), TPEG2-GLR (ISO/TS 21219-21), TPEG2-OLR
(ISO/TS 21219-22);
— Applications: Applications: TPEG2-PKI (ISO/TS 21219-14), TPEG2-TEC (ISO/TS 21219-15), TPEG2-
FPI (ISO/TS 21219-16), TPEG2-TFP (ISO/TS 21219-18), TPEG2-WEA (ISO/TS 21219-19), TPEG2-
RMR (ISO/TS 21219-23), TPEG2-EMI (ISO/TS 21219-25).
TPEG2 has been developed to be broadly (but not entirely) backward compatible with TPEG1 to assist
in transitions from earlier implementations, while not hindering the TPEG2 innovative approach and
being able to support many new features, such as dealing with applications having both long-term,
unchanging content and highly dynamic content, such as Parking Information.
This Technical Specification is based on the TISA specification technical/editorial version reference:
SP13009/1.1/001.
viii PROOF/ÉPREUVE © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
TECHNICAL SPECIFICATION ISO/TS 21219-14:2016(E)
Intelligent transport systems — Traffic and travel
information (TTI) via transport protocol experts group,
generation 2 (TPEG2) —
Part 14:
Parking information application (TPEG2-PKI)
1 Scope
This part of ISO/TS 21219 specifies the TPEG Parking Information application which has been designed
to deliver parking information to a variety of receivers using a number of different channels, foremost
of course are digital broadcasting and Internet technologies. Parking information may be presented to
the user in many different ways, including text, voice, or graphics.
Today, traffic congestion has become a serious problem in urban areas. Some traffic congestion is
attributed to drivers searching for parking spaces. Therefore, timely provision of parking information
could help ease traffic congestion. Furthermore, parking information would be valuable for the visitor,
particularly when it could be used to signal where a temporary parking facility is established for a
special occasion.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO/TS 21219-1, Intelligent transport systems — Traffic and travel information via transport protocol
experts group, generation 2 (TPEG2) — Part 1: Introduction, numbering and versions (TPEG2-INV)
ISO/TS 21219-3, Intelligent transport systems — Traffic and travel information (TTI) via transport
protocol experts group, generation 2 (TPEG2) — Part 3: UML to binary conversion rules
ISO/TS 21219-4, Intelligent transport systems — Traffic and travel information (TTI) via transport
protocol experts group, generation 2 (TPEG2) — Part 4: UML to XML conversion rules
ISO/TS 21219-6, Intelligent transport systems — Traffic and travel information via transport protocol
experts group, generation 2 (TPEG2) — Part 6: Message management container (TPEG2-MMC)
3 Terms and definitions
3.1
Message Management Container
concept applied to the grouping of all message elements including Message Management Information of
a TPEG-Message together in one place
Note 1 to entry: See TPEG2 MMC documents (ISO/TS 21219-6) for full details of the Message Management
Container explanations.
© ISO 2016 – All rights reserved PROOF/ÉPREUVE 1
---------------------- Page: 9 ----------------------
ISO/TS 21219-14:2016(E)
3.2
Location Referencing
means to provide information that allows a system to accurately identify a location
Note 1 to entry: The content of a location reference allows the location to be presented in a graphical or textual
manner to the end-user (e.g. coloured network graphs), as well as to be used for navigational systems purposes.
3.3
Location Referencing Container
concept applied to the grouping of all the Location Referencing elements, of a TPEG-Message, together
in one place
Note 1 to entry: See TPEG2 LRC documents (ISO/TS 21219-7) for full details of the Location Referencing container
explanations.
4 Abbreviated terms
ACID Application and Content Identifier
AID Application Identification
CA Conditional Access
CAI Conditional Access Information
CEN Comité Européen de Normalization
CRC Cyclic redundancy check
EBU European Broadcasting Union
ECM Entitlement Control Message
EMM Entitlement Management Message
MMC Message Management Container
n/a not available
SFW TPEG Service Framework: Modelling and Conversion Rules
TISA Traveller Information Services Association
5 Application specific constraints
5.1 Application identification
The word “application” is used in this part of ISO/TS 21219 to describe specific subsets of the TPEG
structure. An application defines a limited vocabulary for a certain type of messages, for example,
parking information or road traffic information. Each TPEG application is assigned a unique number,
called the Application Identification (AID). An AID is defined whenever a new application is developed
and these are all listed in ISO/TS 21219-1.
The application identification number is used within the TPEG-SNI application ISO/TS 21219-9 to
indicate how to process TPEG content and facilitates the routing of information to the appropriate
application decoder.
2 PROOF/ÉPREUVE © ISO 2016 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/TS 21219-14:2016(E)
5.2 Version number signalling
Version numbering is used to track the separate versions of an application through its development and
deployment. The differences between these versions can have an impact on client devices.
The version numbering principle is defined in ISO/TS 21219-1.
Table 1 shows the current version numbers for signalling PKI within the SNI application.
Table 1 — Current version numbers for signalling of PKI
major version number 1
minor version number 1
5.3 Ordered components
TPEG-PKI does not generally require a fixed order of TPEG components, except where explicitly
modelled. The order for the PKI message components is shown in Figure 1; the first component shall
be the Message Management Container. This shall be the only component if the message is a cancellation
message. Otherwise, the MMC component shall be followed by the one or more Application Data
Container component(s) which includes the application-specific information.
Figure 1 — Composition of TPEG messages
5.4 Extensions
Future application extensions may insert new components or may replace existing components by new
ones without
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.