ISO/IEC 11695-1:2008
(Main)Identification cards — Optical memory cards — Holographic recording method — Part 1: Physical characteristics
Identification cards — Optical memory cards — Holographic recording method — Part 1: Physical characteristics
ISO/IEC 11695 is one of a series of International Standards defining the parameters for optical memory cards and the use of such cards for the storage and interchange of digital data. ISO/IEC 11695 is specific to optical memory cards using the holographic recording method. ISO/IEC 11695-1:2008 defines the physical characteristics of optical memory cards using the holographic recording method.
Cartes d'identification — Cartes à mémoire optique — Méthode d'enregistrement holographique — Partie 1: Caractéristiques physiques
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 11695-1
First edition
2008-11-01
Identification cards — Optical memory
cards — Holographic recording
method —
Part 1:
Physical characteristics
Cartes d'identification — Cartes à mémoire optique — Méthode
d'enregistrement holographique —
Partie 1: Caractéristiques physiques
Reference number
ISO/IEC 11695-1:2008(E)
©
ISO/IEC 2008
---------------------- Page: 1 ----------------------
ISO/IEC 11695-1:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 11695-1:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Holographic memory cards – physical characteristics . 3
4.1 Dimensions. 3
4.1.1 Card height and width . 3
4.1.2 Card thickness . 3
4.1.3 Card corners. 3
4.1.4 Card edges . 3
4.2 Construction. 3
4.2.1 Card construction. 3
4.2.2 Cross-section at accessible optical area . 3
4.3 Physical characteristics. 4
4.3.1 Protective layer(s). 4
4.3.2 Storage layer . 4
4.3.3 Reflective layer. 4
4.3.4 Substrate layer . 4
4.3.5 Additions . 5
4.3.6 Bending stiffness. 5
4.3.7 Card warpage . 5
4.3.8 X-rays . 5
4.3.9 Toxicity . 5
4.3.10 Ultraviolet light. 5
4.3.11 Light transmittance. 5
4.3.12 Bending properties. 5
4.3.13 Resistance to chemicals . 5
4.3.14 Atmospheric requirements . 5
4.3.15 Durability . 5
4.3.16 Dimensional stability and warpage with temperature and humidity. 6
4.3.17 Default test environment and conditioning. 6
Annex A (informative) Holographic data storage. 7
Bibliography . 11
© ISO/IEC 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 11695-1:2008(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
ISO/IEC 11695-1 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identifcation.
ISO/IEC 11695 consists of the following parts, under the general title Identification cards — Optical memory
cards — Holographic recording method:
⎯ Part 1: Physical characteristics
⎯ Part 2: Dimensions and location of accessible optical area
⎯ Part 3: Optical properties and characteristics
iv © ISO/IEC 2008 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 11695-1:2008(E)
Introduction
ISO/IEC 11695 is one of a series of International Standards defining the parameters for optical memory cards
and the use of such cards for the storage and interchange of digital data.
These International Standards recognize the existence of different methods for recording and reading
information on optical memory cards, the characteristics of which are specific to the recording method
employed. In general, these different recording methods will not be compatible with each other. Therefore,
these International Standards are structured to accommodate the inclusion of existing and future recording
methods in a consistent manner.
ISO/IEC 11695 is specific to optical memory cards using the holographic recording method.
Characteristics which apply to other specific recording methods are found in separate International Standards.
This part of ISO/IEC 11695 defines the physical characteristics and the extent of compliance with, addition to,
and/or deviation from the relevant base document, ISO/IEC 11693.
The International Organization for Standardization (ISO) and International Electrotechnical Commission (IEC)
draw attention to the fact that it is claimed that compliance with this document may involve the use of patents.
The ISO and IEC take no position concerning the evidence, validity and scope of these patent rights.
The holders of these patent rights have assured the ISO and IEC that they are willing to negotiate licenses
under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this
respect, the statements of the holders of these patent rights are registered with the ISO and IEC. Information
may be obtained from:
Certego GmbH
Lichtenbergstrasse 8
85748 Garching
Germany
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights other than those identified above. ISO and IEC shall not be held responsible for identifying any or all
such patent rights.
© ISO/IEC 2008 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO/IEC 11695-1:2008(E)
Identification cards — Optical memory cards — Holographic
recording method —
Part 1:
Physical characteristics
1 Scope
This part of ISO/IEC 11695 defines the physical characteristics of optical memory cards using the
holographic recording method.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 7810, Identification cards — Physical characteristics
ISO/IEC 7816-1, Identification cards — Integrated circuit(s) cards with contacts — Part 1: Physical
characteristics
ISO/IEC 10373-1, Identification cards — Test methods — Part 1: General characteristics
ISO/IEC 11695-2, Identification cards — Optical memory cards — Holographic recording method — Part 2:
Dimensions and location of accessible optical area
ISO/IEC 11695-3 Identification cards — Optical memory cards — Holographic recording method — Part 3:
Optical properties and characteristics
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC 11695-2, ISO/IEC 11695-3 and
the following apply.
3.1
holographic recording method
writing and/or pre-formatting of digital data on the holographic memory card in the form of holograms
3.2
hologram
microscopic structure which can be written by optical energy into an accessible optical area causing diffraction
of a read-out beam of certain wavelength by illumination
NOTE 1 A hologram is the representation of a two-dimensional code of digital data on the holographic memory card.
NOTE 2 See Annex A.
© ISO/IEC 2008 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO/IEC 11695-1:2008(E)
3.3
amplitude hologram
hologram which modulates the amplitude of a read-out beam in the read-out process
3.4
phase hologram
hologram which modulates the phase of a read-out beam in the read-out process
3.5
thick hologram
hologram in which the thickness is n times the wavelength of the writing/reading beam, where n >10
3.6
thin hologram
hologram characterized by the thickness of the recording medium containing the hologram, whereby the
hologram has the same order as the wavelength of the writing/reading beam
3.7
holographic memory card
card containing an accessible optical area to which holograms can be written using external optical energy
3.8
accessible optical area
partition of the holographic memory card which is available to be accessed by the read and/or write beam of
the holographic read-out and/or recording system used
3.9
storage layer
specific layer of the holographic memory card, located between the protective layer and the reflective layer,
which contains specific materials to permit writing and/or reading back holographic recorded data by optical
means
3.10
protective layer
transparent layer of material within the holographic memory card which is placed on top of the storage layer
and able to provide protection against scratches, humidity and damage caused by environmental influence
3.11
reflective layer
layer of material within the holographic memory card
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.